No video
how to replace a rear wheel bearing Honda Civic
what's up guys in this video I'm replacing a rear wheel bearing really easy to do don't pay a shot $500 to do this simple job with the right tools you can do it yourself and save money
what's up guys in this video I'm replacing a rear wheel bearing really easy to do don't pay a shot $500 to do this simple job with the right tools you can do it yourself and save money
Пікірлер: 29
You rock man! Straight to the point. I wish everyone was like you.
@luckysdiygarage
5 ай бұрын
Thank you so much!!🙏
Exactly what I’m looking for! This help me out a lot thanks!
No mention of torque values🤔,
Hey what are the exact tool sizes for the bolts needed?
@juang.7309
7 ай бұрын
12 mm x2 for the small bolts holding the line 17 mm x2 for the bolt caliper 17mm x4 for the 4 bolts holding the bearing. Make sure your hammer screw is set to lose lmao. 😂
Made it look easy thanks
Straight to it no bs 30 minutes video 🫡👌🏻🔥
"Wiggle wheel bearing off"... someone's got jokes!
@luckysdiygarage
10 ай бұрын
😂😂
How much should it cost for a bearing replacement? I have brand new 2022 civic with 19k kms on it. Is it ever covered for new cars?
do you have a video for doing the front hub? I don't have a press for just the bearing
@luckysdiygarage
11 ай бұрын
Yes but not for this specific car but similar ones.. if you don't have a shop press autozone rents out the bearing removal and installer tool set 🙂
How are all the parts so clean and no rust? My canadian civic which is 7 years old has rust on all parts. Concernted the bearing will be stuck in the nuckle. Perhaps I should just let a mechanic take care of it.
@luckysdiygarage
Жыл бұрын
If you got a big ass hammer 🔨 to shock it off .. you'll be ok.😁
Thanks for the info, now go get those rims resurfaced god
What are the tools needed to complete this repair?
@luckysdiygarage
Жыл бұрын
I believe I used a 12 mm , 17 mm and Philips socket for the rotor ,and a 3/8 long rachet ...but a good 3/8 8mm to 19 mm socket set 3/8 long rachet blue thread lock will get the job done
@BeatingthePress
Жыл бұрын
@@luckysdiygarage Thank you
No high heat grease between the bearing and nuckle needed?
@luckysdiygarage
Жыл бұрын
Not really but you can apply anti seize between barring and knuckle for easy removal for the next time
@raczyk
Жыл бұрын
@@luckysdiygarage whats the rule when to apply grease or anti seize? For example between the brake pads and caliper bracket, would you use grease or ani seize? People seem to use eaither. What you recommend?
@luckysdiygarage
Жыл бұрын
Yeah for brake pads and caliper bracket I usually never put any brake Grease I only put grease on the slide pins after cleaning them.. and I just installed a new hardware and install the new pads... Some technicians use Grease some technicians use anti-seize some don't add any Grease...
@luckysdiygarage
Жыл бұрын
Depends on the technician
No need to remove ABS sensor?
@khairulanwar9134
Жыл бұрын
Problem abs sensor..
wiggle bearing off 😂🤣... I had to use a low profile hydraulic ram to get mine out 😄
You didn’t have to take out the abs sensor
@ericbaylis1017
Жыл бұрын
??