this is the BEST video on the topic so far on the internet. Thank you brother. ❤

@TheDutchGarage

5 ай бұрын

No problem, glad to help.

You're a good teacher. You explain very well. And you even entertain us by throwing grease to your mouth. 10/10 content 🤣❤

@TheDutchGarage

20 күн бұрын

I'm glad you find it entertaining 😑😉

@joaorovira

20 күн бұрын

@@TheDutchGarage eheheh ❤

This video is first class especially the info about jacking up the opposite wheel. Instead of removing the ball joint I removed the two bolts just behind the ball joint. It took me hours and much anger to get the bolts back in, then I watched this video and followed your advice about levelling the wheels and bingo it all came together easily. Thank you.

@TheDutchGarage

Жыл бұрын

Glad the video was of use. If you don't lift the other wheel you are fighting a massive spring. Good job and some money saved, life is expensive enough.

Thank you! I have benefited from some points that you have showed by replacing my CV joint of my car.

If you want to get the c-clip on without too much hassle, you can wrap a cable tie around it and when you push on the CV joint, if pushing the CV joint pushes the cable tie away from the c-clip, it will be away from the recess and you can cut the cable tie when it's done it's work. Good video - thanks for putting it up.

Excellent presentation, + excellent English, i nearly ordered the complete shaft, now i save a lot by just ordering the CV joint kit. special thanks for sharing.

@TheDutchGarage

Жыл бұрын

Thank you for the compliment!

Great video and good tip with the zip tie, I love the Dutch accent which made it so interesting. Thank you

@TheDutchGarage

2 жыл бұрын

Thank you! Its a Gronings accent (a part of the Netherlands) to be exact. But glad you like it!

Very good..had my cv boot clips done 8 mths ago.and had to have nsf wheel bearing replaced along with cv boot clips again!! Wrong boot clips put on my car..Fed up

Great work! Nice tip to ge the joint in! Thanks!

@TheDutchGarage

3 жыл бұрын

Thank you, It's indeed handy tip.

This is a brilliant video! Top bloke 👍🏻👍🏻

@TheDutchGarage

2 жыл бұрын

Thank you 😊

Nice video. One tip. Put some grease in the joint before putting in on. That way jou lubricate the joint right away.

@TheDutchGarage

3 жыл бұрын

Thank you. I mostly do it when installed less messy. Also I rotate the cv joint to get the grease in. I do think I cut that out.

excellent explanation and job!

@TheDutchGarage

8 ай бұрын

Thank you.

Great video! I am also recommend beforehand put all the grease in the joint and then put it on the car. Love your working style! Success!

@TheDutchGarage

3 жыл бұрын

Thank you! Sometimes I indeed do that also. But most of the times I don't. I just spin the cv joint around a couple of times. It's less messy.

I learnt a lot that's good video l am sure my problem is going to be over

Thx, nice video, we need more video for all cars.

@TheDutchGarage

Жыл бұрын

Thank you, it's alot of work but we do our best.

Thanks! Now to do this on my 2005 Nissan Kubistar, which is actually a rebadged Kangoo.

@TheDutchGarage

Жыл бұрын

Good luck!

Love your channel👍

@TheDutchGarage

Жыл бұрын

Thank you, appreciate it.

Thanks!Great vid.

@TheDutchGarage

2 жыл бұрын

No problem!

I did yesterday complete shaft , it was pain in the ass... they told me it's gonna take around 1hour. That work take 7 hours with 2 experienced guys (some friends walk around with smile on face to ,,help" us😃) ... I never heard that much rude words about French car's 😂 . We did it and it's working well. Renault Megane

@TheDutchGarage

Жыл бұрын

Friend can be assh#ols. 🤣 But 7 hours... that thing must have been really stuck. O well job well done 👍.

That's a great tip - using a cable tie to squeeze the circlip :)

@TheDutchGarage

3 жыл бұрын

It is a good tip indeed.

@moali9316

2 жыл бұрын

Did you cut it off ?

My right axle shaft won't come out of the transmission for some reason? Is it just stuck? 1994 Twingo 1

Hi pal I need cv joint and seen this ring was that 26 abs ring or 44 please. My car is Renault Clio 1.2L petrol manual 07 plate

cool, thank you!

@TheDutchGarage

2 жыл бұрын

No problem.

I tried popping the ball joint out of my e46 years ago and thors hammer wouldn't release it. I could never figure out why mechanic did it with no problems. I think you've just solved that mystery with your comment about lifting both sides!!!

@TheDutchGarage

2 жыл бұрын

That's just the thing sometimes. Bloody Swaybar doing the thing it's designed to do...

@matthewnicholas6365

2 жыл бұрын

@@TheDutchGarage thing is, my mechanic friend didn't have an answer as to why he did it so easily either. I was on the drive way for hours my. Ears are ringing 6 years later from hammering the control arm and the ball joint splitter lol. Guess he did it on a full car lift and he never realised that was why it was easy. 👏

Thanks 👍

@TheDutchGarage

Жыл бұрын

No problem.

Great video as always what would you do without mums car. I am a little confused as to why you did not pull the driveshaft out? I recently had to replace the starter on my Kangoo and needed to pull the right hand driveshaft to get access and did not have a problem. My van is a right hand drive so does this make a difference? I really cannot believe how few people seem to watch your videos and comment but its a good day when you have a new one. All the best to you and your mum.

@TheDutchGarage

3 жыл бұрын

I think it is a force of habit. Most cars if you pullout the driveshaft the gearbox starts leaking. But that's not the case with this car. I appreciate the comment and best wishes. Do something fun today!

@davidauld4854

3 ай бұрын

OK​@@TheDutchGarage

Show us how to change the left side outer joint!

My car has a buzzing sound , seems the wheel bearing is making noise but can not pin point where the sound is comming from .do you have a video from changing bearings

@TheDutchGarage

Жыл бұрын

kzread.info/dash/bejne/YpuVl7KPetfgpZM.html

@michael0192

Жыл бұрын

@@TheDutchGarage Thanks a lot

Great vid , and good english 😆

@TheDutchGarage

Жыл бұрын

Trying my best!😅

I think mines the CV joint. It makes a clunking noise when turning but can't find anything when looked at or replace the noise. Only when moving too

@TheDutchGarage

2 жыл бұрын

If it is clunking you hear its probably one of the cv joints.. if its a grinding noise its probably a wheel bearing.

Toch een hele operatie mooi gedaan ,wat kost zo'n klus nou bij een garage ?

@TheDutchGarage

Жыл бұрын

Exact durf ik niet te zeggen maar rond de 300 vermoed ik.

Vraagje, ik moet de Ashoes van mijn Kangoo vervangen maar dacht de as er geheel uit te halen.. Jij zegt je wilt de as er niet uit halen. Waarom niet? Loopt de bakolie er dan uit? Ik wil niet gaan rammen op de kineet daar die nog perfect is. Hoor het graag van je😀

@TheDutchGarage

2 жыл бұрын

Klopt, de bak loopt dan leeg. Dit in natuurlijk geen groot probleem. Je zou hem dan bij moeten vullen of verversen.

@Hombrewrx

2 жыл бұрын

@@TheDutchGarage ok top, opnieuwe vullen met verse olie is geen probleem, ander vraagje, iets vreemds.... Onder m'n koppeling pedaal ligt was olie.. Van de koppeling dus want komt uit het gat waar de koppelingskabel naar buiten gaat... Nooit eerder gezien.. Heb jij een idee? Koppelt verder prima en geen rare geluiden.

@TheDutchGarage

2 жыл бұрын

Kan het zijn dat het rem olie is?

@Hombrewrx

2 жыл бұрын

@@TheDutchGarage ja heb ik ook gedacht ja maar dat reservoir is netjes op pijl... Dankje 😀

@TheDutchGarage

2 жыл бұрын

Mischien eens naast gegoten door iemand.

What if you pop the shaft out the gearbox

@TheDutchGarage

3 ай бұрын

No panic. You only lose some oil. So be sure to add some to the gearbox if that happens.

moi video en echt goed reparatie , now forgive me for my netherlands .

@TheDutchGarage

Жыл бұрын

Your dutch is better then mine I have a heavy groningen(part of the Netherlands)accent.

@lampros1911

Жыл бұрын

@@TheDutchGarage next week I ll be in Groningen, I would love to see your place , plus jij kunt gereedschappen vonden bij HBM voor echt goed prijs

280nm aanhaalmoment van je aandrijfas??? Is dat serieus Renault specificatie?? Volvo S40/V50/C30 is slechts 35nm en dan 90 graden.

@TheDutchGarage

Жыл бұрын

Torque specs kunnen inderdaad veel verschillen vanuit diverse boeken. De specs die jij geeft zijn " torque to yield" specs. De kans is aanwezig als je het zou na meten dat je dan ook rond die 280 uit komt.

I try everything I can’t find cv join for my Renault Clio

@TheDutchGarage

Жыл бұрын

Try autodoc or ebay.

this is not for Twingo, just separated the joint by shattering the parts side of that joint!!!!!!!!!!!!! Watch out what name of car models you put on the youtube title.

@TheDutchGarage

5 ай бұрын

Really, that's odd. The parts numbers are the same for the twingo. I will look into it, Sorry for the situation you are in, and thank you for the feedback.

I'm single. Where do I find a wife's favourite potato peeler?

@TheDutchGarage

2 жыл бұрын

Well then you can't do this job.