Just replace the union hardest part is done to remove union replace with new union, just friendly advice 🤙
@jamesknightreading2 жыл бұрын
I think it's a mistake to use sealant. The gutter needs to expand & contract in the fitting, but sealant will lock it in place. Just put a new seal in IIWY.
@PaintingandDecorating
2 жыл бұрын
OB1 sealant will flex and is perfect for this type of job where slight expansion can occur...
@raydavison2972
5 ай бұрын
@@PaintingandDecorating The whole reason you shortened the gutter length is to allow sufficient expansion. The OB1 won't allow that much expansion
@Ramblingpete
3 ай бұрын
👍🏿👍🏿👍🏿correct
@user-mh1ec4wd9p4 күн бұрын
Before you cut the old gutter to length, make sure it fits into any other union or running outlet. Might just need re positioning
@marklittler7843 ай бұрын
"Here's a seal ! " Reminds me of Blue Peter and Play School "Here's one we made earlier !" 😅 Amazing how you just happen to have a seal 😊
@chaddamp28942 жыл бұрын
another great vid thanks
@PaintingandDecorating
2 жыл бұрын
Thank you.
@yorkshiresfinest61024 ай бұрын
Put a screw in the union otherwise it will leak under continuous strain from rain water. And the union should have rubber gaskets in not just some silicone. Far easier to replace old union for a new one at a cost of around £3
@markbucsenac583516 күн бұрын
The sealant that you used was probably more expensive than a new union
@GretatheEvilGremlin2 жыл бұрын
Really not worth messing around, union brackets are less than £3! Can tell by the easy way the clip snapped on, that there's not much meat on that gasket for it to clamp tight.
@Ramblingpete3 ай бұрын
Just by a new one man Job done 5 mins
@margaretjones4192 жыл бұрын
Dear sir could you give me advice on how to use dulux easycare with a brush I found that the paint is dragging when you blend in and pulling the previous brush strokes off making patches. I have watered it down slightly but it is still doing it , I hope the next coat rectifies this . I am painting fresco paper Thank you.
@PaintingandDecorating
2 жыл бұрын
If it's first coat on wallpaper.. this can happen best to ignore and just get first coat on even.. second coat should go on better and leave s great finish.. thanks
@margaretjones419
2 жыл бұрын
Thankyou.
@richardscotchmer5922 жыл бұрын
Surely it would be easier to put a brand new joining bracket on the spend time cleaning it and siliconing one side
@PaintingandDecorating
2 жыл бұрын
Not really... this fix will last for years... extra time wasted going getting one and fuel.. fix and repair will always save you money.. people just want easy fix even if it costs them more money... and trust me the way thinks are going we all need to save..
@johnnyoldskool65042 жыл бұрын
Another job well done 👍
@PaintingandDecorating
2 жыл бұрын
Thank you.
@joshlehan80572 жыл бұрын
Excellent so satisfying to watch 👍
@PaintingandDecorating
2 жыл бұрын
Thank you glad you enjoyed.
@mariaescosura3972 Жыл бұрын
Do you work in London? My gutter wasn't fixed properly so when it rains the water falls in the windowsill.
@ttsstt1000
Жыл бұрын
Get adecent handy man will do it for a 40 ish quid charge its easy
@mariaescosura3972
Жыл бұрын
@@ttsstt1000 thanks!
@TapelessDrywallFinishing2 жыл бұрын
👍👍👍
@PaintingandDecorating
2 жыл бұрын
Thank you.
@davidbrown257110 ай бұрын
A new seal does not always work, ive found even a new fitting can leak,annoying when youve put new joints on.
@saudilass2 жыл бұрын
Legend 👌👍🏻
@PaintingandDecorating
2 жыл бұрын
Cheers
@paulf25292 жыл бұрын
The labour involved in messing about cleaning the old bracket etc really isn't worth it. Better to just buy a new coupler and change it. I've never seen this sort of repair to last long term no matter what sealant etc used. If I had to do a quick fix then In my opinion denso tape is hard to beat and will cope with expansion and contraction.
@PaintingandDecorating
2 жыл бұрын
It is these days.. tape would look terrible.
@paulf2529
2 жыл бұрын
The denso tape goes inside the joint so you would never see it.
@Ramblingpete3 ай бұрын
There note made for sealant no no just saying
@truckman41752 ай бұрын
Why when a new one is £2.50 drrrrrrrr
@PaintingandDecorating
2 ай бұрын
Kill the planet. 😅
@adl200511 ай бұрын
and the union should be screwed to facia to stop it moving.
@PaintingandDecorating
11 ай бұрын
Yes you're correct.
@adl200511 ай бұрын
just get a new union
@PaintingandDecorating
11 ай бұрын
Why waste money?
@mastervidzsoundz910511 ай бұрын
keep life simple and replace the union couple quid save all the faffing about all together 5 min job instead of...6.minutes 52 secs of yr precious time 😆😆😆😁😁😁😁
Пікірлер: 41
Just replace the union hardest part is done to remove union replace with new union, just friendly advice 🤙
I think it's a mistake to use sealant. The gutter needs to expand & contract in the fitting, but sealant will lock it in place. Just put a new seal in IIWY.
@PaintingandDecorating
2 жыл бұрын
OB1 sealant will flex and is perfect for this type of job where slight expansion can occur...
@raydavison2972
5 ай бұрын
@@PaintingandDecorating The whole reason you shortened the gutter length is to allow sufficient expansion. The OB1 won't allow that much expansion
@Ramblingpete
3 ай бұрын
👍🏿👍🏿👍🏿correct
Before you cut the old gutter to length, make sure it fits into any other union or running outlet. Might just need re positioning
"Here's a seal ! " Reminds me of Blue Peter and Play School "Here's one we made earlier !" 😅 Amazing how you just happen to have a seal 😊
another great vid thanks
@PaintingandDecorating
2 жыл бұрын
Thank you.
Put a screw in the union otherwise it will leak under continuous strain from rain water. And the union should have rubber gaskets in not just some silicone. Far easier to replace old union for a new one at a cost of around £3
The sealant that you used was probably more expensive than a new union
Really not worth messing around, union brackets are less than £3! Can tell by the easy way the clip snapped on, that there's not much meat on that gasket for it to clamp tight.
Just by a new one man Job done 5 mins
Dear sir could you give me advice on how to use dulux easycare with a brush I found that the paint is dragging when you blend in and pulling the previous brush strokes off making patches. I have watered it down slightly but it is still doing it , I hope the next coat rectifies this . I am painting fresco paper Thank you.
@PaintingandDecorating
2 жыл бұрын
If it's first coat on wallpaper.. this can happen best to ignore and just get first coat on even.. second coat should go on better and leave s great finish.. thanks
@margaretjones419
2 жыл бұрын
Thankyou.
Surely it would be easier to put a brand new joining bracket on the spend time cleaning it and siliconing one side
@PaintingandDecorating
2 жыл бұрын
Not really... this fix will last for years... extra time wasted going getting one and fuel.. fix and repair will always save you money.. people just want easy fix even if it costs them more money... and trust me the way thinks are going we all need to save..
Another job well done 👍
@PaintingandDecorating
2 жыл бұрын
Thank you.
Excellent so satisfying to watch 👍
@PaintingandDecorating
2 жыл бұрын
Thank you glad you enjoyed.
Do you work in London? My gutter wasn't fixed properly so when it rains the water falls in the windowsill.
@ttsstt1000
Жыл бұрын
Get adecent handy man will do it for a 40 ish quid charge its easy
@mariaescosura3972
Жыл бұрын
@@ttsstt1000 thanks!
👍👍👍
@PaintingandDecorating
2 жыл бұрын
Thank you.
A new seal does not always work, ive found even a new fitting can leak,annoying when youve put new joints on.
Legend 👌👍🏻
@PaintingandDecorating
2 жыл бұрын
Cheers
The labour involved in messing about cleaning the old bracket etc really isn't worth it. Better to just buy a new coupler and change it. I've never seen this sort of repair to last long term no matter what sealant etc used. If I had to do a quick fix then In my opinion denso tape is hard to beat and will cope with expansion and contraction.
@PaintingandDecorating
2 жыл бұрын
It is these days.. tape would look terrible.
@paulf2529
2 жыл бұрын
The denso tape goes inside the joint so you would never see it.
There note made for sealant no no just saying
Why when a new one is £2.50 drrrrrrrr
@PaintingandDecorating
2 ай бұрын
Kill the planet. 😅
and the union should be screwed to facia to stop it moving.
@PaintingandDecorating
11 ай бұрын
Yes you're correct.
just get a new union
@PaintingandDecorating
11 ай бұрын
Why waste money?
keep life simple and replace the union couple quid save all the faffing about all together 5 min job instead of...6.minutes 52 secs of yr precious time 😆😆😆😁😁😁😁