How to remove your Ferguson TE20 Clutch and Flywheel
Автокөліктер мен көлік құралдары
Please support our channel by purchasing merchandise here: bundybearsshed.com/
Hello Im Lance (aka Bundy Bear) and doing these videos is my hobby. I do own Queensland Tractor Spares in Australia where I sell parts and offer technical advise to customers.
Parts seen in our videos can be purchased from www.queenslandtractorspares.co...
We have a lot more than we can offer on our web site available to us and in our store. If you dont see what you would like please email info@queenslandtractorspares.com.au and we will help where we can.
I do try and help with technical advise at bundybearsshed@gmail.com if you have a question or are having trouble with your project.
Пікірлер: 38
I have a 1949 TO20 that i am wanting to rebuild, looking for a couple of parts tractors. I did find an unused drawl bar that was like hitting the lottery because over here in the USA most of them have been all wobbled out of round due to pulling over weighed loads. You're a tremendous help, and you're video will be of help. Thanks.
@BundyBearsShed
Жыл бұрын
Thanks, Glad you get something useful from the videos.
As always very informative, will be a great help when I split my 1947 Fergy
@BundyBearsShed
2 жыл бұрын
Glad to help
As usual another wonderful video on the Ferguson tractor
@BundyBearsShed
2 жыл бұрын
Glad you enjoyed it
Nice job and I enjoyed the video.
@BundyBearsShed
2 жыл бұрын
Awesome, thank you!
Great video as always I am going to look a ted tomorrow love 🇬🇧
@BundyBearsShed
2 жыл бұрын
Have fun!
@ryno8547
2 жыл бұрын
Was no good still looking
Heya mate, keen viewer from over the ditch here. Can't stress enough how mint your videos are. I'm rebuilding a MF 35 petrol myself so this stuff is fantastic. Quick question: when you said this tractor has a 'stuck' clutch, does that mean it was stuck with the pedal in the depressed position (no power going to the wheels or the other way round? Cheers.
@BundyBearsShed
4 ай бұрын
Stuck as in the plate was stuck onto the flywheel and even though the pedal was feeling good the clutch would not release.
Bloody interesting Lance..........John
@BundyBearsShed
2 жыл бұрын
Thanks John.
Thank you for your helpful video! I have a Massey Harris Pony and the clutch has started sticking a little and when I took the starter off it is very oily inside. I guess I need to look at changing the rear engine seal.
@BundyBearsShed
Жыл бұрын
Yes and have a good look at the front gearbox seal while you are there, it is probably easy to do with the tractor split.
@toolreviewsandrestorations
Жыл бұрын
@@BundyBearsShed I'll have a look at that too since the goal is to have a tractor that doesn't leak. The Pony tractors actually have a frame around the engine so rather than splitting it like the tea 20 I have to take the engine out.
G'day. Was surprised to see so few bolts holding that heavy flywheel on.
@BundyBearsShed
2 жыл бұрын
Yes and they are only small. only 20hp though.
Hello from Sweden, you videos of the Fergie are very good. A question, the finger springs that hold the fingers to the pressure plate, do they sold seperatly or do they only come with the pressure plate. One more time thanks for your videos, take care.
@BundyBearsShed
5 ай бұрын
Not available separately as far as I know on the early clutches but on the 9"/11" etc they are.
@skraekken
4 ай бұрын
Ok, thanks Lance, take care.@@BundyBearsShed
gREAT STUFF
@BundyBearsShed
Жыл бұрын
Thanks Geoff.
One nice tyre on the Fergie, Olympic Gripster, a great shame they are not made here anymore, or anywhere.
@BundyBearsShed
2 жыл бұрын
Yes thats for sure.
Hello! I have oil leaking where the bell housing bolts to the engine. I have been assuming it is engine oil, but is there any way it could be the transmission/diff/hydraulic oil?
@BundyBearsShed
Жыл бұрын
Not normally, the trans oil will often leak from the little tell tale hole further back.
If you marked the position of the ring gear relative to the flywheel, removed the gear and rotated it 45deg before refitiing it would that work as a quick fix?
@BundyBearsShed
2 жыл бұрын
Yes it does, I have done that myself and the newer lead in helps. I have also re ground the lead in and that can work too if you are out on site and need to get going.
Noah says hello Lance 🤣
@BundyBearsShed
2 жыл бұрын
Ask him did he have two Unicorns on the Ark.
@JACKATTACKED
2 жыл бұрын
He said na, reckons they were taking a Fergie to Methuselah Motors to get fixed and that made them late
@BundyBearsShed
2 жыл бұрын
@@JACKATTACKED lol
Could you give me an idea of why my P.T.O. lever slides out of gear when I have it engaged? I have to keep a bungee cord attached to it while brush cutting in order for it to stay engaged. Any thoughts?
@BundyBearsShed
2 жыл бұрын
I think your PTO shaft may have a twist in it from hitting something causing it to ride out.
@randyjennings23
2 жыл бұрын
@@BundyBearsShed I never would have thought of that. Thank you!