“Glued On” should be hyphenated in your video title. With the way you have the title written now, you are talking about something called “on mirrors” and describing them as glued.

@NextLevelCarpentry

4 жыл бұрын

Serious-ly?! Good-grief! 🙄🙄

@KidCity1985

4 жыл бұрын

Ok mom.

@kansascityshuffle8526

4 жыл бұрын

Next Level Carpentry you never know he may have been born yesterday.

@NextLevelCarpentry

4 жыл бұрын

@@kansascityshuffle8526 Only child of English professor parents maybe?

@kansascityshuffle8526

4 жыл бұрын

Next Level Carpentry yeah or some kind of former childhood prodigy.

Having removed hundreds of mirrors in similar fashion, the rule of thumb is... If you want to re-use the mirror it WILL break, if not it will come off cleanly and in one piece.

@vidpie

2 жыл бұрын

I have a bathroom with a large mirror attached to a slanted ceiling. Any tips on removing a mirror so situated?

@matthewwarfield4302

2 жыл бұрын

@@vidpie Have never encountered one like that! I would spread a large drop cloth and get some help to support the mirror as you try to take it down. Eye protection and gloves are MANDATORY! Long sleeved shirts and maybe even heavy jackets, since it's on an angle. Heavy putty knives to slip behind and GENTLY pry the mirror loose. 4" and bigger help to spread the pressure on the mirror. Steady even pressure is the key... Don't be in a hurry. Slip 2x4 blocks, or what ever you can get behind it, to help reach deeper behind the mirror to pry up if you need to. You'll eventually get to where you can grab the edge of the mirror and pry up. That's when you know you've got it pretty close to coming off. If it breaks, it breaks. Start prying up again. Good luck!!

@vidpie

2 жыл бұрын

@@matthewwarfield4302 Thanks for the detailed response. I think this job may be too much for me given my inexperience and gravity. The mirror is 4ft wide x 5 ft long. There are a couple of clips on each vertical side that are likely driven into the rafters. They are not identical so one type might have been added later. The bottom horizontal edge abuts a large mirror on the wall behind the vanity. The other edge of the vertical mirror rests on the vanity backsplash.

@matthewwarfield4302

2 жыл бұрын

@@vidpie I would cover them both with a sheet and get the hammer out. You'll be surprised at how hard you have to hit it to break it. Clean up the mess and pry off any stuck to the wall pieces. Good luck!

@vidpie

2 жыл бұрын

@@matthewwarfield4302 Great advice. Thanks for the encouragement.

I've never seen such a patient contractor - with the work AND the teaching. great video editing as well!

When possible, I use picture hanging wire to remove mirrors secured with mastic. Thread the wire behind the mirror, then use a sawing motion to cleanly cut through the mastic/tape. This technique sometimes isn't possible due to clearance, but when it is, it works like a charm. I've never had a break. Like you, I also donate furnishings and fixtures that are in good condition after removal to Habitat for Humanity ReStore!

@NextLevelCarpentry

4 жыл бұрын

I'm glad to hear this testimony from a reliable source John... I've heard about using the wire method but just can't envision a smooth wire slicing through those big globs of time-hardened mastic. With your anecdote though I'll keep it in my 'bag-o-tricks' for the future! Thanks... Best, Matt

This video helped me finally get my mirror off my bathroom wall. Using your shimmy idea worked far better than numerous other videos I seen that recommended using a heat gun. I did make sure that I thoroughly taped the mirror. This ensured holding the mirror together if anything went wrong. I highly recommend anyone who has never done this before to tape prior to removal.

Stick on carpet protector stuck to the mirror will keep the mirror help keep the mirror together if it breaks as it covers the whole mirror. Thanks again

@NextLevelCarpentry

4 жыл бұрын

Inexpensive, easy and effective... great tip Monte! Thanks for adding it here... Best, Matt

@jonesconrad1

4 жыл бұрын

we used to do that with windows, just tape the whole thing up and wack it.

@trevorblue

4 жыл бұрын

that stuff has a bazillion uses, I hear it works pretty good at protecting carpet too

Having seen you remove a sheetrock wall with no mess on a previous video, as soon as I saw the title, I knew you were again going to deliver a new method I would want to learn! Kudos!

As another old pro I have to recommend always keeping safety goggles (the bigger plastic ones) on as I noticed you didn't have any eye protection after you removed them when you was carrying them off. Love all the great tips, thanks.

Had a friend of mine almost loose an arm when the mirror shattered and sliced thru his forearm. The bleeding was extensive. Put sticky carpet protector on the mirror face before you remove it or invest in Kevlar shirt/sleeves so we can watch the rest of your vids with you having both arms.

Dang, Boy! I needed that video a couple of years ago. Being a total novice DIY homeowner, I made every possible mistake taking done a big mirror. Lucky I didn't sever an artery. Now I know a number of techniques to prevent disaster due to the Master. Thanks!

Nicely done! Recently used shims to remove an under mount sink. It was stainless steel with silicone caulk as an adhesive to marble top. It worked great! David

Years ago I removed about 35 4'X8' mirrors off a condo gym wall the same way. Great job as always.

Great stuff!!! A very good way to remove glued mirrors. I'll use this method when I need it, no doubts. Thanks for sharing.

This is another great illustration that faster is not always better. Those who think they save time by bashing the mirror into tiny pieces will spend more time cleaning up said tiny pieces than they saved. Gotta love the thoughtful, methodical approach.

Thanks for the awesome video. My wife and I removed a large mirror using the techniques we learned from your video. Worked like a charm. Thank you for taking the time to make and post the video.

Thank you for taking the time to make this video. It was really helpful with our bathroom project!

Matt... You're fast becoming my favorite KZread channel. Well done.

@Peter-.H

4 жыл бұрын

Nathan: i agree 👍 Awesome videos.

This is one of the most well thought out, comprehensive and brilliant home-improvement videos I've seen on KZread.

@NextLevelCarpentry

2 жыл бұрын

Thanks for sayin Doug... if you like this video I think you'll find more equally informative ones here at Next Level Carpentry 😁😎 Best, Matt

Love this! I see all too many smash it up demos - this is brilliant!

Matt, awesome level of work, love you repurpose the old hardware and cabinets with habitat for humanity. Another level of additional work on your side benefiting others is a mark of a good man. Thank you for the video. Never thought about using shims, excellent. Hooked on your channel. Thank you for great 👍 inspiration in solving problems.

Great stuff, as always! "Electricianizing"....now I have another thing to call my trade =) We did a minor update on our hall bath several years back. Basically a taller vanity with a granite top. There was a mirror mounted pretty much identical to the way yours were, but larger - it's about 40" tall, but 8' wide. Goes from the end wall of the sink all the way to the tile for the shower. I had no idea how to remove this and really wanted to save it if possible, but figured that was very unlikely, as even pro glaziers say "good luck". My granite guy (who is awesome) had just done my kitchen and was going to do a cheap granite top on my craigslist vanity. I mentioned the mirror and he said no problem very confidently. I was doubtful he would be successful, but his confidence was unwavering. So bathroom remodel day comes. Josue (my granite guy) breaks out 2 of those suction cup handles - pro ones though, and puts them on the mirror roughly in thirds. I'm like are you sure; what do you need me to do? he said "nothing, I got it". so he just grabs both handles and starts pulling and jiggling the handles in and out and in about 10 seconds he has the mirror off without a scratch on it. It was held on with huge blobs of black mastic-looking adhesive. He put the mirror in the other room. We set the new vanity. He revised the floor tile a little bit, and cut and installed the new top and splash, complete with a beautiful hand -cut hole for the sink. He then set the mirror with new adhesive and it was done. Looks great and took like 1-1/2 to 2 hours. I had all the prep work done before we started - vanity and sink removed, light fixture removed and box relocated, new vanity drilled for plumbing, etc...Just another technique to throw in the toolbox of ideas...I do like the shim idea, though ;-)

Excellent video and advice. We used shims and glass lifting suction cups as you suggest and were able to remove a 4'x6' bathroom mirror without breaking it. There aren't even any cracks! Thanks so much for posting this video.

Second favourite MJ tip after the sheetrock removal video. Nice work matey.

Glazier here that's put in hundreds of mirrors like this. Really well done, great method, I'll definitely be using this method in the future. Your videos are always great!

Good work 👍 I contracted with a glass company to remove wall to wall mirrors, that went to the ceiling. Flashback to the 70s. They used a lot more tape and brute force pulling on the vacuum suction cups, to detach the mirrors from the walls. Copious amounts of broken mirror had to be cleaned up when it was over.

This is a very helpful video! I own my own glass shop and in the past glued on mirrors were always taken down by breaking them up. I don't use a hammer though. I cut them up with my glass cutter and take them off in pieces. Next time I have a call for this I'll give your method a try. Thanks for the idea.

Just found your site and as a life-long amateur with a decent eye I am excited to find the kind of help you are providing. Thank you.

@NextLevelCarpentry

4 жыл бұрын

Glad to hear it Michael.. welcome to Next Level Carpentry! Feel free to comment on other videos you find helpful... you sound like my prime demographic so I'm interested in what resonates and what is irrelevant. Best, Matt

Intriguing method, thanks for the insight - glad to know all the furniture will get another life where its needed.

Another well presented lesson. Thanks Matt.

Wonderful comment on Habitat for Humanity. It speaks volumes of your character and your stock just went up a lot in my book! Bravo!!

Nice tip. That looks like a pretty nice bathroom. I am surprised they are ripping it out and redoing it. Glad you recycle them.

@GeorgeMinton-jb8ky

4 жыл бұрын

When you have money you can change any bathroom no matter what the cost. Someone probably bought the house and did not like the previous owner's taste maybe.

Once again, very slick, very smart and safe. Thank you.

Whatever this guy charges, IT'S WORTH IT! Great, Great, Great!

You are just SUPERB "SIR " AWESOME SKILLS.

Very ingenious! I use lots of Duct tape, Gloves, and a long sleeve Shirt, and where possible a Hand Saw slipped behind to help cut the Glue. Getting up above the Mirror the way you did is a lot safer incase the Shards fall.

He was clear and to the point! Great job!

I was extremely happy to find this video, my house has a few of those mirrors and I want to fancy them up. But after watching the video I'm just going to dress them up with door casings and call it a day. Great information though, thanks!

Nice work Matt!

Having watch more than a few of your videos it hit me that if you had an extra long or tall mirror you could take one of your super shims cut it into sections that would fit between the top of the mirror in the ceiling and gradually send the shims down stacking the sections on top of each other to eventually get the mirror completely loose with that cream and putting your hands behind it. Great video always learn some something when I watch your videos. My take away today was too soon old too late smart. That might make an amazing T-shirt as well. As always thank you man wish you the best.

Great method, Matt. Better and safer than one I have used extensively. In another lifetime, I removed thousands of square feet of mirror as we toured the country remodeling a mall store chain as they transitioned from one architectural model to another. Each store had a wall of full length mirrors, each about 3' wide x 7' tall, and very well adhered with the original blobs of mirror mastic applied years before. The stores also had chrome rolling fixtures, which happened to include removable flat hanging bars, about three foot long with sectional size, 1/4" x 1". In the heat of battle on one of the first jobs, I discovered that I could slide one of these thin bars behind the mirror with its 1" flat side against the wall and use it extremely gingerly as you would a crow bar to gradually work the mirror off the wall. Because these bars were not rigid enough to keep from bending, their flexibility made it possible to gradually work a mirror off the wall without breaking it. I don't recommend this method without reservation to others, as it requires practice and a very sensitive touch to avoid causing a sudden crack, which can be dangerous. But back in the day, I got proficient enough through all the repetitions to remove enough mirror to equip two dance studios and one martial arts dojo wall to wall after I started hauling the undamaged pieces back home to make a little bonus cash.

@NextLevelCarpentry

4 жыл бұрын

Great anecdote 'from the trenches' Michael! Glad to hear you're able to repurpose them because it always pains me to toss a perfectly good mirror for the fact it has glue on the back and it's a custom size... Best, Matt

HGTV would have used the hammer...and then spent 3 hours off camera cleaning up the shards. Good work Matt. I've had good luck removing mirrors that way too.

I'm glad that no shims were harmed in the making of this video. I was quite worried that they may have splintered or split. I've been hoping that you would show a video removing a wall mirror ever since your closet makeover when you said that you wished you had filmed it. I also have three that I want to remove, and if possible, have them cut down and put into a frame for reuse.

Matt, these tips are absolutely golden. These are the kinds of work methods the separate the good contractors from the best. I wish you lived closer to me. I’d gladly pay for you to some work for me like my next task... replacing a broken 5’ X 8 ‘ window on the back of my house. Not too bad but I have full shutters inside (that have to be removed) and brick outside (that was installed after the window). Thanks for posting.

@NextLevelCarpentry

4 жыл бұрын

I'll let you know when I take my dog-and-pony show on the road Dwight... I'll plan a stop in your fair city along the way! 😁😎 Non-typical non-routine window replacements are a bit of a specialty service I offer. Clients appreciate it when requirements and conditions require more planning and outside the box thinking than common new window upgrade jobs. Best, Matt

Good work good tips and good introduction of tools to be used during removal process. thank you.

Matt. Great Video. I always wondered the best way to do this.

I've never seen the shims being used like this. I have always used wire to saw thru the adhesive. Then again, I have not come across a mirror hard up against a wall or cabinetry. This, I will try on my next reno. Thanks

Matt, your videos are amazing now compared to your first efforts! Thanks for all your tips and tricks, I have learned a lot from your videos. Keep up the good work!

@NextLevelCarpentry

4 жыл бұрын

Hey Chris; thanks for noticing and commenting on video quality here. Learning video production skills (such as they are) has been one of the toughest challenges I've taken on in recent years. It can still be frustrating but it's encouraging to know at least a little progress is visible! From one Jackson to another: Best, Matt

Awesome job! I've removed mirrors like this also, though those longer shims make it look easier! I use the Wood Powr-Grip suction cups but these look like they worked just fine! Awesome job on presentation, love watching your videos!

I did this about a year ago, when I went to change out a bathroom light fixture and found a splice just living in the wall, which led to finding 3 hidden j boxes behind the drywall, and redoing the bathroom's electrical. Fun times.

Ingenious Matt awesome work👌🏽👌🏽

Watching from Scotland gid video pal keep them up 👍

Great tips, thank you for sharing! That wallpaper looks like Medusa's hair if she went to a luau.

Great work, thanks for the video

Thank you for the great tips and well made instructional video(s)

Thank you very much for sharing this video with me. I really need to get this done and I have to do it by myself.

Very helpful and nice tools. Thanks for sharing.

Great video, very informative.

This helped so much! luckily the Mirror was stuck with double sided tape so no wall damage! Thank you!!

Great job, pal, I will use it right away, thanks.

Outstanding presentation. Your ability to do the work and also narrate the video is commendable. Old video but thanks for the lesson on removing a mirror!

@NextLevelCarpentry

Жыл бұрын

You're quite welcome Robert... thanks for watching and commenting! Best, Matt

Nice job n great information. Thank you

Great job! By your video I can see this job may be too challenging for a ONE “OLDER” person job. For that I am grateful! I like doing DYI’s but I won’t be tackling this one by myself.

Watched your tutorial and removed my mirror with no issues and in one piece 🤗 Slow is key, for sure .. and PPE. Thank you so much!!!!

@NextLevelCarpentry

Жыл бұрын

Very cool... thanks for letting me know and kudos for grasping the key takeaway from the video: slow is the way to go!

Great video, this will help in our remodel !

Always a helpful interesting video.

I like your style big man, keep shooting your videos, (a beginner wood worker from scotland)

In this bathroom there was a lot of space above the mirror so you can make some custom long shingles at the same 1/4" per foot bevel, (ie 1/16" to 9/16" for a 2' shingle, or 1/16" to 13/16" for a 3' shingle). That reduces bending of the mirror and allows it to be pushed out from the middle as the shim is pushed down and not just at the top.

You had me at "Too soon old and too late smart"

This really helped me, thank you

Gotta get me a "Whimmy-Jimmy" screwdriver!! Great video, thanks!

I don’t know why you said you did it by yourself; there were always two and I saw as many four workers in there at one point. Matt, Chip, Chap, and Chump. Thanks for the great lesson Matt!

@frankherring6253

4 жыл бұрын

If you would have used a sky hook on that mirror it wouldn’t have fallen like that!

Total pro Matt......always !

@NextLevelCarpentry

4 жыл бұрын

Thanks for watching and commenting Don... hope all's well in your world... or acceptable at least? Best, Matt

That was pretty cool, thank you

Great video Matt! I watched because I'm going to remodel the bathrooms in the house we bought. They have floor to ceiling mirrors on the sink and vanity side for some unknown insane reason. I cant use shims. Can you suggest an alternative method? Thanks

Hey Matt great Video! I've recently found your channel. Really enjoy it and your humor cracks me up. I've learnt so much from your videos already. Thank you!

@NextLevelCarpentry

4 жыл бұрын

Welcome, Tom. Glad you discovered NLC and get a chuckle or two while learning. I question putting 'silly stuff' in the videos for fear it will cause viewers not to take me seriously so I'm glad to know it's not a detractor for you. Even if it negatively affects KZread view stats there's little chance I'll quit including 'humor'... I just can't seem to help myself when it comes to ad-lib silliness. 🤡🤡 Best, Matt

@tomgilberg8038

4 жыл бұрын

Is there anywhere where we can ask you questions about our own projects?

@NextLevelCarpentry

4 жыл бұрын

@@tomgilberg8038 not on Next Level Carpentry... unfortunately it's just not feasible. There's plenty of woodworking forums where you might find answers. For me, personally, I do a bit of consulting on an hourly basis but, for most projects, the cost would be impractical/prohibitive. I might consider adding an hour of consulting for Patreon Patrons at some level but haven't had the time/need to do so as yet. Best, Matt

Great information!

YOURE THE MAN!!

Great idea.

I'm about to do this again... I wish I had seen this video. SOOOO much safer and easier. Great content.

Good tip. I had success using fishing line in the past

Good job! Now I know how to take the mirror backing off my St Michael deco.

I was guessing at the beginning of the video (before you showed the shims) that you would use a thin wire or twine to run behind the mirror to saw through the adhesivie. I'm suprised that the mirror could flex that much without breaking. Maybe the mirror backing helps to reinforce the glass? Another great video!

Very informative Matt. I have to admit, I had a slight case of puckeritus as you were working those mirrors off. I hate glass, to many bad experiences with it. Though, as usual, you make it seem easy. Oh, and you are correct about that wall paper. That might have looked good from the back of a galloping horse tho.

Great video. Thanks!

Worked geat!! Thank you so much!

Just for the sake of future mirror installations. It's recommended to apply the glue in vertical stripes not blobs. Adhesive should be applied thoroughly in the corners to prevent possible cracking. Remember not to push the mirror to hard when installing because it will be curved.

Great tips thank you

Great tip!

Great video thank you for sharing

Great video. You answered my question.

I tried out your technique using shims and duct tape to removed mirrors for a wet bar nook remodel and it worked perfectly, thank you

@NextLevelCarpentry

2 жыл бұрын

Glad to hear it thanks for letting me know! Best, Matt

Great job

Lol 😂 he had me for a sec with the rubber hammer.

@inezae.eliane798

3 жыл бұрын

Same 😂😂

I'm wondering if you made flat shim extensions that were like open-ended crest wrenches on one side and you used them to drive the first shims further down. The extension shims could be used in series to drive each other and ultimate the first shim. could probably peel the glass complete away from the wall even if lots of adhesive was used.

Great advice

Wow great idea thank you for sharing 😀 🇬🇧

can you go into some detail on how you would repair the glued areas after removing mirrors? thx

This video will be very useful as I have a bathroom remodel coming up in a bit. Thank you Matt for the class

@NextLevelCarpentry

4 жыл бұрын

You're welcome Tom. I'm sure there's a mirror 'out there' that won't come off with this method but its definitely what I'd use as a first attempt. BTW I figure that using the longest shims possible with similar taper would give you a better chance if your mirror doesn't seem to yield to removal like the ones in the video did. You probably noticed the photo at 2:35 which was the first mirror I did using shims. That thing was REALLY stuck with both mastic and strips of doublestick tape. Luckily I was able to slip shims in from all 4 sides because otherwise I don't think it would have come off without breaking... but longer shims might have made a difference. Best, Matt

@tomtruesdale6901

4 жыл бұрын

@@NextLevelCarpentry I have used dental floss to remove emblems from car/motorcycle parts, I wonder is something like that would work if you had room the saw it back and forth behind the mirror? Might have to give it a try one day

@NextLevelCarpentry

4 жыл бұрын

@@tomtruesdale6901 I like the floss/emblem tip... thanks again! Best, Matt

@tomtruesdale6901

4 жыл бұрын

@@NextLevelCarpentry works well and does not scratch the paint

Love your show, my only suggestion would be to line up the shims with the studs especially if the mirror is really stuck to the wall.

Great video. How much does the mirror weigh? I plan to remove one that size. Thanks