Great. Thank you.

@SpiritedWrenchers

29 күн бұрын

Thank you Sam for watching and sharing the kind words. We appreciate it. Cheers!

@samdalia01

29 күн бұрын

I ​never removed a broken bolt before. Broke the bolts off my oil pan. I urchased everything you had in the video and with some patience and praying I was able to extract the broken bolt thanks to you

@SpiritedWrenchers

29 күн бұрын

@@samdalia01 Thank you so much for sharing. This is awesome. Love hearing that we were able to help you out. You nailed it, it's all about patience when it comes to getting these out. Congrats on getting it done all on your own!!!

That was absolutely amazing- congrats sir. I have a couple of bolts that have a years long need to be done-

@SpiritedWrenchers

Ай бұрын

Thank you Vic for watching and sharing the kind words. We really appreciate it. Good luck with getting your bolts out as well. Cheers!

Aahhh! Murphys law my friend!! I expect that every day pays to be prepared, thanks for great vid

@SpiritedWrenchers

2 ай бұрын

Sounds like you're familiar with him as well. LOL. Thank you for watching and sharing the kind words and laugh. Both greatly appreciated!

That's awesome! I usually break at least one extractor before I get a bolt out.🤣😳

@SpiritedWrenchers

Жыл бұрын

Thanks for watching brother. Yeah, that's exactly the way I thought this would go knowing our luck. Fortunate for once. LOL.

Do you drill clockwise or counterclockwise?? On the harbor freight screw extractor set says to drill counterclockwise

@SpiritedWrenchers

Жыл бұрын

Thank you for watching and asking. We greatly appreciate it. Yes, these drill bits are backwards compared to your normal bit. You would run it counter clockwise as if you're backing a bit out. Hope that helps.

This is great to see that they work so well. You just never know with less expensive tools. Thanks for sharing. Need to add these to my tool box now.

@SpiritedWrenchers

Жыл бұрын

Thank you for watching and sharing the kind words. We appreciate you.

so you hammer in the extractor as opposed to drilling it in? Is that piece you re hammering in the same as a left handed drill bit? i m so F n lost time to pay a pro to get broken bolt out

Perfection

@SpiritedWrenchers

11 ай бұрын

Than you for watching and sharing the kind words. Much appreciated!

My cotter pin broke into the metal shaft so i attempted to drill it out. the titanium drill bit broke and now its stuck in the hole, does anybody know how to get that out?

so why do you need a left hand drill bit? can't you use a regular one and then use the bolt extractor?

@SpiritedWrenchers

Ай бұрын

Hi Jack. Thanks for asking. We appreciate it. It's the direction of the threads that are different. It all works together to extract it. Hope that helps.

Sulute ✊🏾🔥💯

@SpiritedWrenchers

11 ай бұрын

Thank you for watching and sharing the kind words. We appreciate you.

I have a set of those, but find myself using the welder to extract them more often.

@SpiritedWrenchers

Жыл бұрын

Thanks for watching Evan. We appreciate it. Yeap, that's certainly a great option. I decided to take the dive and add a small one to my list this year and I guess Santa thought I was nice after all. LOL. Now I need to teach myself how to use it. 🙂

@EvanWells07

Жыл бұрын

@@SpiritedWrenchers one of the best tools you can have around the shop! Not only will it help with working on vehicles, but you can also fab up other tools and make stuff you wouldn't even have thought of before.

What’s the difference between a left hand screw extractor & a right hand? Or is there not a right hand?

@SpiritedWrenchers

6 күн бұрын

Hi Whatshisface. Thank you for watching and asking. We really appreciate it. So the bits are left handed, not the extractor. The bits are fluted in a counter-clockwise direction so it doesn't tighten the broken bolt any further. It's a good first step with the hopes that it might loosen it before using an extractor. Hope that helps.

@whatshisface1390

6 күн бұрын

@@SpiritedWrenchers thank you for responding!

@SpiritedWrenchers

6 күн бұрын

@@whatshisface1390 our pleasure.

Strong work. How much pressure did you have to apply on the hand drill and how long did it take to drill? I find the bit doesn't want to bite on the bolt

@SpiritedWrenchers

Жыл бұрын

Hi siegeperilous. Thank you for watching and asking. It's one where you have to have patience. I've also discovered recently that if the bolt or screw is incredibly hard steel, they won't bite. I had to start the hole with a titanium bit and then switch over. Little pressure and patience is when I was successful or you run the risk of braking the bit. Hope that helps. Cheers!

@jackmorgan709

Ай бұрын

might need to use a cobalt bit - much harder than titanium or high speed stel

Would you recommend this for extracting a screw from a tailgate actuator that is stripped and stuck?

@SpiritedWrenchers

Жыл бұрын

Hi 133thefallen. Thank you very much for watching our video and asking. We appreciate that. It's very difficult to say as it's dependent on the size of the screw and location. If it's big enough to drill into without hitting any electronics, it could be possible. Without seeing it, I'm cautious to advise with a certain yes. There may be better products for stripped screws.

@133thefallen

Жыл бұрын

@@SpiritedWrenchers thank you for taking the time to reply. It doesn't seem that using this would hit any electronics from what I saw. I will try it though

Why the need for left handed drill bits? Isn't a hole a hole? Thanks!

@Guitarfollower22

5 ай бұрын

Because if it grabs the material enough to spin it during it, it will be backing it out each grab rather than tightening it

@SpiritedWrenchers

5 ай бұрын

Thank you Guitarfollower22 for contributing to our community and helping others. We really appreciate it!

@Goonies-xh3qr

5 ай бұрын

@@Guitarfollower22 Gotcha! That did cross my mind. I have 4 bolts that broke off my sewage pump basin lid I need to back out and replace. Going to pick up a combo set at the local Harbor Freight. Thanks and Merry Christmas!

A 16 sided socket works easier than a cresent wrench.

@SpiritedWrenchers

Жыл бұрын

Hi DeeJay, thanks for watching and sharing the tip with everyone. Much appreciated!

I have the same problem. NO PATIENCE!

@SpiritedWrenchers

Жыл бұрын

LOL. Thank you for watching and sharing Floyd. Glad to hear we share a same trait. Hahaha. Cheers!

This took too long and uninformative

@SpiritedWrenchers

8 ай бұрын

Thanks for taking the time to watch and share Christian.