Your vid is the only one that stated to tap the extractor into the hole at around the 27 minute mark. Guess what? That is what saved the day for me. I was applying pressure on the extractor to the bolt and it wasn't doing a thing. Used the hammer with light pounding on the extractor, turned counter clockwise and removed the broke stud like butter. Thank you for the great vid!!

@Abletrot

Жыл бұрын

Glad it was helpful.

you did a VERY VERY GOOD JOB demonstrating and explaining THANK YOU!!!!!!!!!

A++ video! Really good information. Thanks for taking the time to provide this.

Excellent reference. Thank you.

Awesome video, awesome skills !

You save my day, Thank you!!!!

Just what I needed , thank you.

@Abletrot

Жыл бұрын

You're very welcome

Amazing! Best vid on the subject! After watching, I'm gaining confidence to tackle my broken stud!

Accurate first step

Thank you.

@Abletrot

3 ай бұрын

You're very welcome.

Where can I buy the left-handed drill bit set not that bothered about the extractors as I have a decent set just can't find decent left hand drill bits

@Abletrot

Жыл бұрын

If you just search left handed drill bits, the results should have a number of good options. Some of the better brands are Irwin, Cleveland Twist Drill, and Cle-line. But those are not the only ones out there.

.... PRICELESS.....

If I was looking for someone to extract a rounded off bolt that holds my drive belt tensioner in who would I look for? I've tried pretty much every method but welding because i don't have a tig weld and theres little to no space in the area. It is a completely round e12 that sits in the hidden part of the tensioner ( you have to pull it back to see it).

How much will it cost if I bring this problem to the bike/car center?

@Abletrot

3 жыл бұрын

It depends on their experience and cost of labor. A base charge of 35-50 USD per bolt is a common range.

Where can I order this magical stud remover?

@Abletrot

2 жыл бұрын

Google "16023 Stud Extractor" I've used the Titan and Performance Tools brands with great success. They are also sold a many auto parts stores.

Much more difficult when the bolt is broken off below the surface and the part is not aluminum but cast iron or steel.

@ambread1

3 жыл бұрын

When ye end mill broke did you replace it or pocket the doh?

@Abletrot

3 жыл бұрын

You are absolutely right, but sometimes you can build up the bolt by welding it. And in the case of cast iron or steel an oxy fuel torch can be used to blow out the bolt.

@Abletrot

3 жыл бұрын

If an end mill breaks it usually shatters and the pieces can be blow out of the hole then I'll give it another try with an end mill before I go to EDM removal.

@jasondjenkins

2 жыл бұрын

@@Abletrot where you located Matt? I have broken head stud in block I need to get out I’m located in OKC.

@jasondjenkins

2 жыл бұрын

@@Abletrot 405-641-6297

Gee, I figured in Texas they would use a 12 gauge slug and lots of cus words. I am shocked they would resort to using rinky dink tools

@Abletrot

Жыл бұрын

Who's to say I didn't soften them all up with the 12ga. Honestly I try the fastest and least invasive techniques first, but sometimes it gets to the point where it looks like a shot gun was used then I have to fix it all back to original.

i NEED A TOOL TO EXTRACT A HONDA BELT CONTROL MODULE,IT WAS A ALLEN BOLT.

@Abletrot

3 жыл бұрын

Sometimes if the hex of the Allen bolt is rounded you can use a Torx bit by tapping it into the rounded hex.

First view 😎

@djmellow5011

3 жыл бұрын

onlyy view