#lathe #automotive #racing this is how to turn a material piston into a ready-to-use piston using a material film piston
Жүктеу.....
Пікірлер: 70
@TheGreatInquisitor Жыл бұрын
То чувство, когда у тебя капремонт, а поршней на старый двигатель в продаже нет...и ты натыкаешься на это видео. Вы, таки, дарите людям надежду, мой друг.
@AmrinderSingh-zx9hr Жыл бұрын
Good job
@Kostya1984. Жыл бұрын
Хорошая работа,коллега!)
@z1lla4
Жыл бұрын
Водка
@nyakpatria02142 жыл бұрын
Muantep jost
@marque7583 Жыл бұрын
Impressive...
@kamtoputra8414 Жыл бұрын
this is already costing me double, i laughed at this
@den3171 Жыл бұрын
Короче говоря, был изготовлен нормальный поршень, с хорошей юбкой, красавчик!
@kuswelderart2 жыл бұрын
Good job👍👍
@llewvirtue8612 жыл бұрын
it is scary but I suppose it may run. this much machining, where I live would make this A golden piston
@rinimemasak2 жыл бұрын
How to modif piston so good
@MrApmotos Жыл бұрын
hard work
@davidshelton8762 жыл бұрын
Can't believe I've just sat and watched someone destroy a piston!
@scottyjones27
Жыл бұрын
I'm not experienced in piston making I'm just DIY fix my stuff man this man here lives on a rock in the middle of the Pacific ocean he has had to make stuff work Not as intended if I was needing my scooter fixed on said rock i ask this man how to !! I'm sure his scooter is the fastest on rock
@trxtech3010
Жыл бұрын
@@scottyjones27 Deffinatly not. As someone who has biuld many engines here this guy has no clue what he is doing. Also using a Cast Aluminum Piston o make a high compression piston is a horrible idea.
@eduardonostalgia1643
Жыл бұрын
Como você acha que as coisas são fabricadas? Principalmente em lugares onde não há recursos tecnológicos! Lembrando que tudo em seus primordiais eram feitos em máquinas manuais operadas por humanos e o produto final funcionava sim...
@trxtech3010
Жыл бұрын
@@eduardonostalgia1643 Farts
@thefreedomguyuk2 жыл бұрын
Where would one be able to buy the Eyeball Dialling-in Precision Tool you seemed to use ??
@leoarc1061
2 жыл бұрын
You can find it in most hardware stores. Hit Or Miss Ltd, Close Enough Retail, Screwed Again, etc.
Morten it's called experience which I'm sure you lack
@vilivilian9751 Жыл бұрын
Muy bueno!
@Arifinsyahpratama Жыл бұрын
Mantaap bang. Sy ikut nyimak bang,
@primangoprek86272 жыл бұрын
Kerja bagus kawan
@fernandezcastilloguzman4126 Жыл бұрын
Que hay del revestimiento del cabezal. Si lo a cepillado vastante. Tercamente no resiste. La comprensión
@Haya3usaGsxr9 ай бұрын
You can build a set for me ?
@heetecht9974 Жыл бұрын
แข่งกับ สจ.นัมเบอร์วันป่าว ร้านเอ็งอ่ะ
@peterh76052 жыл бұрын
How thick is the piston crown after that much machining?
@KULITEHNIK
2 жыл бұрын
approximately 5mm , with this shape the valve part is very close to the piston ring ( people order )
@thefreedomguyuk
2 жыл бұрын
Not thick enough....
@hiperformance71
Жыл бұрын
@@thefreedomguyuk it depends of the application, from what I see, 5mm can be enough for a Naturally Aspirated engine
@horahore5175
Жыл бұрын
@@thefreedomguyuk it's enough. Use 13:1 compression ratio. Huge valve, stroke up, extreme camshaft profile upgraded Ignition, porting polish, proper cooling will boost the horsepower from 14 to 30HP minimum
@den3171
Жыл бұрын
@@thefreedomguyuk при нормальной эксплуатации хватает.
@williamgilchrist8577 Жыл бұрын
I understand what you did and the methodology you used to reach the end point. What was the piston used for to begin with and what did you modify the piston to fit into for use? Unless I know that then all I see is someone just cutting some aluminum. Maybe I am just thick or something or something but I do not see why you modified the piston. I have to assume you modified the piston for a racing application.
@hiperformance71
Жыл бұрын
from what I see, he has a "sporty" piston damaged (is broken in the crown, first 3-5 seconds of the video), took a piston with huge compression height (distance from the compression ring and the top of the piston), and made some machining to copy it the crown. from a machining point of view, the guy has amazing manual skills, no doubt. From a thechnical point of view, if the objective is to make this engine more "compressed" instead of buying expensive forged pistons (the one he copied is clearly a forged piston) it may be good considering the costs involved, but for performance point of view, is no way, the sporty piston is lighter and stronger, the piston he used to modify is cast aluminum, it is heavy compared to the sporty forged one, but, I can understand, when you do not live in a rich country, you need to adapt at what you have, is like "made it in a budget" but more extreme way.
@Hydrogenblonde
Жыл бұрын
He is just making a replacement. The engine maybe getting bored to the next oversize.
@92gashaulass43
Жыл бұрын
Yes for modified cam and bigger valve size,need more valve lift clearance due to modified cams
@azka_family0424 Жыл бұрын
Boleh boleh bang
@ardianjodi8950 Жыл бұрын
Wah hebat ya
@mirzamirza2180 Жыл бұрын
Bengkelnya daerah mana mas
@shandykurniawan9517 Жыл бұрын
Pisau bubutnya kurang center mas
@faridprayoga5215 Жыл бұрын
Saya pastikan itu piston goyang, kurang presisi
@joramotorsportteam3277 Жыл бұрын
Where you get pistons for tuning?
@92gashaulass43
Жыл бұрын
Buy raw dome pistons,LHK brand is most popular hyperteutic piston choice With great quality but limited in pin size
@dianbedee8855 Жыл бұрын
Bang itu piston jenis apa dan punyanya motor ap?
@seregasergeew1253 Жыл бұрын
От какого автомобиля поршень?
@user-fn3nl9mx7q
Жыл бұрын
.. мопед..
@dufus7396 Жыл бұрын
Thank you..I do Lada...Brmmm mmm
@ormasoren5051 Жыл бұрын
lain kali kalo bubut piston jgn di tekan gitu,lebih bagus di buat dudukan ke pen piston saolnya nya kalo di tekan diameter berubah,pengalaman ku
@KULITEHNIK
Жыл бұрын
Skill operator beda2 boskuh ini piston masih lunak , pake dudukan pen itu juga sama klo k tetekan aga kuat jg berubah dia meter belakang, al hasil yg honing ketipu karna doer bagian belakang, terimakasih masukanya boskuh 👍 🙏
@ormasoren5051
Жыл бұрын
@@KULITEHNIK ga pernah berubah kalo makek pen,kalo kek kerja kau tu iya berubah
@ironmike742
Жыл бұрын
@@ormasoren5051 I guess he told you. Keep watching and you may learn something
@michaeliovine2462 Жыл бұрын
I'll just buy a Wiseco piston
@hiperformance71
Жыл бұрын
the problem probably is, that the country where the guy lives is not as rich as US or the EU, probably he can buy 8-10 sets of pistons with the money you can buy Wiseco pistons, some peoples need to adapt to their economy/environment.
@ironmike742
Жыл бұрын
@@hiperformance71 I don't understand why people can't see that. They use what they have to make what they need. Which is lost in this new millennial Era. People can be nasty
@trxtech3010 Жыл бұрын
Just seeing the title makes me realize this guys engines arent very powerful lol
@victormanuelavilasantoya7931 Жыл бұрын
no resistirá la comprensión, además no me gustó tampoco la manera de tornear, el torno girando para atrás, no es necesario para hacer éste trabajo, la reversa del torno solo se utiliza en ocasiones exclusiva, cuando sea muy necesario porque es la única opción. pero no es muy recomendable. Soy especialista en operador de máquinas y herramientas, con muchos años de experiencia. Saludos desde Moscú.
@progaragechinskiemotorki2 жыл бұрын
co to jest za tłok ?
@KULITEHNIK
2 жыл бұрын
we take from the piston fim brand, the material is adjusted to your needs
@progaragechinskiemotorki
2 жыл бұрын
@@KULITEHNIK ale gdzie dokładnie taki tłok kupię :D
@boboyboooyyy5177
Жыл бұрын
@@progaragechinskiemotorki online shop Indonesia
@johnhoylessceptreofself-so6214 Жыл бұрын
What's with all these foreign lathe operator videos where they stop the chuck with their hand. Foot way to break a few fingers... Or an arm, or lose them.
@garykarenmcgruther6386 Жыл бұрын
He has to be extremely poor with a friend with a machine shop or stupid. I would order a blank then start there but not at that shop. Nope, notta
@dull2114 Жыл бұрын
kbanyakan tukang bubut motor benda kerja blm center udh hajar
Пікірлер: 70
То чувство, когда у тебя капремонт, а поршней на старый двигатель в продаже нет...и ты натыкаешься на это видео. Вы, таки, дарите людям надежду, мой друг.
Good job
Хорошая работа,коллега!)
@z1lla4
Жыл бұрын
Водка
Muantep jost
Impressive...
this is already costing me double, i laughed at this
Короче говоря, был изготовлен нормальный поршень, с хорошей юбкой, красавчик!
Good job👍👍
it is scary but I suppose it may run. this much machining, where I live would make this A golden piston
How to modif piston so good
hard work
Can't believe I've just sat and watched someone destroy a piston!
@scottyjones27
Жыл бұрын
I'm not experienced in piston making I'm just DIY fix my stuff man this man here lives on a rock in the middle of the Pacific ocean he has had to make stuff work Not as intended if I was needing my scooter fixed on said rock i ask this man how to !! I'm sure his scooter is the fastest on rock
@trxtech3010
Жыл бұрын
@@scottyjones27 Deffinatly not. As someone who has biuld many engines here this guy has no clue what he is doing. Also using a Cast Aluminum Piston o make a high compression piston is a horrible idea.
@eduardonostalgia1643
Жыл бұрын
Como você acha que as coisas são fabricadas? Principalmente em lugares onde não há recursos tecnológicos! Lembrando que tudo em seus primordiais eram feitos em máquinas manuais operadas por humanos e o produto final funcionava sim...
@trxtech3010
Жыл бұрын
@@eduardonostalgia1643 Farts
Where would one be able to buy the Eyeball Dialling-in Precision Tool you seemed to use ??
@leoarc1061
2 жыл бұрын
You can find it in most hardware stores. Hit Or Miss Ltd, Close Enough Retail, Screwed Again, etc.
@ferrumignis
Жыл бұрын
Always remember: 1) Measure twice 2) Cut once 3) Discard 4) Repeat
@Hydrogenblonde
Жыл бұрын
It's called experience.
@dull2114
Жыл бұрын
he called es cream 🤣
@ironmike742
Жыл бұрын
Morten it's called experience which I'm sure you lack
Muy bueno!
Mantaap bang. Sy ikut nyimak bang,
Kerja bagus kawan
Que hay del revestimiento del cabezal. Si lo a cepillado vastante. Tercamente no resiste. La comprensión
You can build a set for me ?
แข่งกับ สจ.นัมเบอร์วันป่าว ร้านเอ็งอ่ะ
How thick is the piston crown after that much machining?
@KULITEHNIK
2 жыл бұрын
approximately 5mm , with this shape the valve part is very close to the piston ring ( people order )
@thefreedomguyuk
2 жыл бұрын
Not thick enough....
@hiperformance71
Жыл бұрын
@@thefreedomguyuk it depends of the application, from what I see, 5mm can be enough for a Naturally Aspirated engine
@horahore5175
Жыл бұрын
@@thefreedomguyuk it's enough. Use 13:1 compression ratio. Huge valve, stroke up, extreme camshaft profile upgraded Ignition, porting polish, proper cooling will boost the horsepower from 14 to 30HP minimum
@den3171
Жыл бұрын
@@thefreedomguyuk при нормальной эксплуатации хватает.
I understand what you did and the methodology you used to reach the end point. What was the piston used for to begin with and what did you modify the piston to fit into for use? Unless I know that then all I see is someone just cutting some aluminum. Maybe I am just thick or something or something but I do not see why you modified the piston. I have to assume you modified the piston for a racing application.
@hiperformance71
Жыл бұрын
from what I see, he has a "sporty" piston damaged (is broken in the crown, first 3-5 seconds of the video), took a piston with huge compression height (distance from the compression ring and the top of the piston), and made some machining to copy it the crown. from a machining point of view, the guy has amazing manual skills, no doubt. From a thechnical point of view, if the objective is to make this engine more "compressed" instead of buying expensive forged pistons (the one he copied is clearly a forged piston) it may be good considering the costs involved, but for performance point of view, is no way, the sporty piston is lighter and stronger, the piston he used to modify is cast aluminum, it is heavy compared to the sporty forged one, but, I can understand, when you do not live in a rich country, you need to adapt at what you have, is like "made it in a budget" but more extreme way.
@Hydrogenblonde
Жыл бұрын
He is just making a replacement. The engine maybe getting bored to the next oversize.
@92gashaulass43
Жыл бұрын
Yes for modified cam and bigger valve size,need more valve lift clearance due to modified cams
Boleh boleh bang
Wah hebat ya
Bengkelnya daerah mana mas
Pisau bubutnya kurang center mas
Saya pastikan itu piston goyang, kurang presisi
Where you get pistons for tuning?
@92gashaulass43
Жыл бұрын
Buy raw dome pistons,LHK brand is most popular hyperteutic piston choice With great quality but limited in pin size
Bang itu piston jenis apa dan punyanya motor ap?
От какого автомобиля поршень?
@user-fn3nl9mx7q
Жыл бұрын
.. мопед..
Thank you..I do Lada...Brmmm mmm
lain kali kalo bubut piston jgn di tekan gitu,lebih bagus di buat dudukan ke pen piston saolnya nya kalo di tekan diameter berubah,pengalaman ku
@KULITEHNIK
Жыл бұрын
Skill operator beda2 boskuh ini piston masih lunak , pake dudukan pen itu juga sama klo k tetekan aga kuat jg berubah dia meter belakang, al hasil yg honing ketipu karna doer bagian belakang, terimakasih masukanya boskuh 👍 🙏
@ormasoren5051
Жыл бұрын
@@KULITEHNIK ga pernah berubah kalo makek pen,kalo kek kerja kau tu iya berubah
@ironmike742
Жыл бұрын
@@ormasoren5051 I guess he told you. Keep watching and you may learn something
I'll just buy a Wiseco piston
@hiperformance71
Жыл бұрын
the problem probably is, that the country where the guy lives is not as rich as US or the EU, probably he can buy 8-10 sets of pistons with the money you can buy Wiseco pistons, some peoples need to adapt to their economy/environment.
@ironmike742
Жыл бұрын
@@hiperformance71 I don't understand why people can't see that. They use what they have to make what they need. Which is lost in this new millennial Era. People can be nasty
Just seeing the title makes me realize this guys engines arent very powerful lol
no resistirá la comprensión, además no me gustó tampoco la manera de tornear, el torno girando para atrás, no es necesario para hacer éste trabajo, la reversa del torno solo se utiliza en ocasiones exclusiva, cuando sea muy necesario porque es la única opción. pero no es muy recomendable. Soy especialista en operador de máquinas y herramientas, con muchos años de experiencia. Saludos desde Moscú.
co to jest za tłok ?
@KULITEHNIK
2 жыл бұрын
we take from the piston fim brand, the material is adjusted to your needs
@progaragechinskiemotorki
2 жыл бұрын
@@KULITEHNIK ale gdzie dokładnie taki tłok kupię :D
@boboyboooyyy5177
Жыл бұрын
@@progaragechinskiemotorki online shop Indonesia
What's with all these foreign lathe operator videos where they stop the chuck with their hand. Foot way to break a few fingers... Or an arm, or lose them.
He has to be extremely poor with a friend with a machine shop or stupid. I would order a blank then start there but not at that shop. Nope, notta
kbanyakan tukang bubut motor benda kerja blm center udh hajar