Source Code and 3D stl files - www.pcbway.com/project/shareproject/Quadruped_Spider_Robot_3D_Printed_Parts_SG90_Servo_Motor_Arduino_Nano_10107fe3.html Required Components: 12x SG90 Servo Motor - amzn.to/3TYPrgj 1x Arduino Nano V3 - amzn.to/3FBhApv 3x Capacitor 100uF 16V - amzn.to/3DNbcJt 1x LDO Voltage Regulator 5V/3A (Similar: MIC29310-5.0WT, LM1085IT-5.0, LM323T) 12x Header Male 2.54 1x3 - amzn.to/3fybH1A 1x 6 Pin Self-Locking Switch 8x8mm - amzn.to/3SWbQcU 1x Screw Terminal Block Connector 5mm - amzn.to/3FC8EQB 1x LED 3mm - amzn.to/3FBj6rH 1x Resistor min. 220 Ohm - amzn.to/3TZdR9J 2x 18650 Li-ion Battery - amzn.to/3zYvKO3 1x 18650 Battery Case 2 Slots - amzn.to/3fu5sMr Required Tools: Soldering Station - amzn.to/3TVvZkQ Soldering Wire - amzn.to/3ST5ElX Wire Cutter - amzn.to/3h2APy6 Silicone Soldering Mat - amzn.to/3SXpDA5 Isopropyl Electronics Cleaner - amzn.to/3frlG93

@dayzbrk

Жыл бұрын

merhabalar mert bey, eldiven ile robot el projesinde elin parmaklarını tek tek hareket ettirdiğimde hiç bir sıkıntı olmuyor ama tüm parmakları aynı anda hızlıca kapattığımda arduino kafayı yiyiyor ve donuyor. Resetleyince tekrar kafası yerine geliyor. Bunun sebebi ne olabilir, yardımcı olur msuunuz?

@ayoubhsaine6060

Жыл бұрын

the code is empty

Looks like a funny robot project. At this rate, Mert Arduino's robots will take over the world :)

@maker101io

Жыл бұрын

Grateful for your nice comments! ❤🚀

Good job! Good video! I am really stunned by this great robot!!!

@maker101io

Жыл бұрын

Woow! thanks for your nice comment ❤️🚀

Awesome project, I like it very much. Definitly will make something like this.

@maker101io

Жыл бұрын

Thanks for your nice comment 💯🚀

The coolest project

@maker101io

Жыл бұрын

thanks 😇

Amazing creation

@maker101io

Жыл бұрын

Thanks 🤖

@armantape

Жыл бұрын

@@maker101io ok

Bro can you please tell me the specification of the screw that you have used.

Amazing I always like to come to your channel and learn thank you...

@alvarobyrne

Жыл бұрын

Me too

@maker101io

Жыл бұрын

Thank you very much, I hope I can contribute a little! 🚀

hi i have a question concerning the voltage of robot, what is the range of the voltage and current to supply the spider

Hey, Can you please help me my motors are doing anything they want one of them goes up some another goes down but they follow the same walking pattern

hi! great video and project by though bro :). I want to ask something by the way. if i want to use a bluetooth like HC05/HC06 will the schematic be the same as yours?

Hey can I get the PCB file for this project you have shared only the picture of the connections because we are using bread board instead of PCB

Bro my ardiuno is not getting power from motor driver shield, when I connect to computer it’s ardiuno is working , when I connect it with battery it’s stops working

do you have any computation for its legs lengths and size, how do you come up with those sizes?

I can’t make this robot slow down. servos are at high stress. how to slow down it’s walking?

are your li ion batteries connected serial or parallel? I’ve two batteries

This is super cool! Any chance you could drop the 3D print files along with the links? I’m planning on making something similar to this for a project. Thanks!

@maker101io

Жыл бұрын

Thanks for your nice comment ❤️ ok I will be add as soon as possible 💯

Please make something like that with HC-05 for manual controls

@maker101io

Жыл бұрын

thanks for idea, I will try to make it 🙂

how many month for you to complete this project ?

canyou do this code for adafruit pca9685 by any chance?

How much euro is it all

100th like! 😉🙂

@maker101io

Жыл бұрын

Thanks 💯🚀

Bro there are too many servos, Great vid though 🤯

@maker101io

Жыл бұрын

yeah 🥴It was a bit of a hassle! 🤫😆

🌟🌟🌟🌟🌟👏yine süper.

@maker101io

Жыл бұрын

This is my mom! I love you mom ❤️❤️❤️😃

What is uses of the spider robot