00:54 33leds are in parallel connection not series connection

Great looking project I indent to make myself. Could you please supply the gerber for the controller PCB, Cheers. Keep up the good work.

Your every project is very good keep it up

You did a great job brother. keep this type of work going on ❤❤

Nice

Great work... May i know the thickness of the 3d printed diffuser?

Wooow I'm love with this video u are the best 🖤

awesome work brother

I believe the second configuration may work if you had a diffuser behind. Like an aluminum sheet. The first configuration is cooler and allows a lot of effects but is too much work

Hello, cool project and i would like to make this but am i correct and is in the gerber file the controller pcb missing?

good...👍

❤️❤️❤️

Great job but so many questions. Did you provide an idea for the power supply? When you buy the Node MCU v3 does it come with the tan plastic thing that you soldered it to?

@electronautic5510

Жыл бұрын

Using 5v 5amp power supply. U can configure it in Wled by putting the output amp of your power supply. I have used the generic esp8266 module. Tan plastic is a female berg strip. not needed if u soldered directly. I have used it so that I can easily remove the esp module when needed.

@hagsmich

Жыл бұрын

@@electronautic5510 thanks for your response, many utubers don't even respond to questions.

Great video, one question, why the green wire is not used?

howw i order the same pcb as you use here????

Hi Bro, Inspired from your work I have requested the creator of Corsair iCue Emulator Node MCU to include support for LC100. So that the nano leaf sort off gets connected to the iCue. Can you please check it and make a video. I am getting my 3D printer this week and will be trying that myself as well. Thanks

you could use magnets between the lights 😀

@tinatarentino8356

8 ай бұрын

How does it work? Where can you buy such joints?

You did a great job my friend. Could you please share the pcb gerber file?

Great video! Can you please make a link for the PCB design?? I also use EasyEDA and am interested to make this project.

@electronautic5510

Жыл бұрын

Sure

@electronautic5510

Жыл бұрын

www.mediafire.com/file/48gdesry3re14w5/PCB_PCB_nano+leaf_3_2023-04-03.json/file

@SimonSaysNL

Жыл бұрын

@@electronautic5510 Thank you so much!! Definitely earned a new sub!! ;)

In every panel you have put 60 leds total in count.. But in program.. You mentioned 27 in every segment.. Hows that...? Also if I dont use pcb and directly put led strip just as ur prev project where you created small size, how should be connection. Can you please give digram of circuit? How can i stick 60 led strip in circular as you did but without pcb... Using wired connection as your project previously. Could you please give circuit connections diagram for it?

@electronautic5510

Жыл бұрын

Some led are in parallel connections that's why 27 led count. Without PCB, not possible, too much wire will make a mesh inside and it will block the light and create a shadow.

What is total cost?

hello can you please share the pcb file so we can order the custom pcb on pcbway?

How do you connect every single piece ?

@electronautic5510

2 жыл бұрын

All are connected with connector. Inside each pannel there was a connector check the video from 02:49

@immortalpg4586

2 жыл бұрын

@@electronautic5510 ohh ok and please tell me how you created the base which have imprints of solder and how much overall it cost to you

@electronautic5510

2 жыл бұрын

Check on KZread how to make pcb.each pannel cost approx rs600

What is the max number of pannels?

@electronautic5510

2 жыл бұрын

10,20,30 whatever you want just need to put the value 'number of led' in wled.

@Dr_Khanz

2 жыл бұрын

Max no of led for WLED progrms is 960 I guess, im not sure

@karlschuneman7960

5 ай бұрын

16

The green wire is not used, correct?

@weavy5476

2 жыл бұрын

I also have several other questions pertaining to the power supply. Could I email you?

@electronautic5510

2 жыл бұрын

Yes

S4S

3D printer ... ok 😂 👍

Nice