Great build and very innovative use of a drill bit with spiral flutes. There have been a lot of makers with straight flutes, but I like the spiral, and old bits are fairly easy to come by. Thanks and cheers! Someone should forward this vid to homemade tools.

@Mastermind-

9 ай бұрын

I'm so glad you enjoyed it my friend🙏👍💐

Great job my friend! You left out only one thing, tempering. it is very important that the tool is not brittle, because one wrong move can break the teeth. in the case of tool steels, they undergo multi-step hardening, which makes the material very resistant. great job by the way!

@Mastermind-

9 ай бұрын

Thanks for the watching and the tips my dear friend🙏🙏💐💐

@ALittleBitOfEverything-wd9ee

12 күн бұрын

For tempering steel that needs to stay very hard, like for a tap, sometimes just boiling water is hot enough, and if that leaves it to brittle, an oven at 150 degrees C might work

Красавчик ! Чистюля !! Приятно , когда все почти идеально !!! Успехов ❤ , за наждачку и образив минус😢

With no doubt, the very best tap. I know because I made some myself in desperation, on weekends where I need it one and every shop were shut, but the cheapest tap would do the job in good hands.

@Mastermind-

4 ай бұрын

Thank you so much my dear friend🙏🙏🙏💐

Absolute HOCHACHTUNG! Das war der Beweis, daß es noch echte Handwerker gibt! 🎉

@Mastermind-

4 ай бұрын

🙏🙏🙏💐

This video really makes me appreciate just being able to buy one.

@Mastermind-

5 ай бұрын

🙏🙏💐❤️

A handmade tool is always a reason to be proud. Congratulations and best regards 😀.

@racing_mntage1584

Ай бұрын

Exactly, I feel proud everytime I use things that I made or restored

@Mastermind-

15 күн бұрын

Thank you very much my friend I hope other friends like you will understand the value of this work and not be superficial

@Mastermind-

15 күн бұрын

🙏🙏❤️👍

@ZygmuntKiliszewski

15 күн бұрын

Thank you for the like 😀.

You should note that drill diameter are actually slightly smaller than stated size and tap diameters are slightly larger, so take care for a screw to fit the tapped hole!

Damn fine work! That was some quality stuff. It's also nice to see someone that actually does things correctly and properly when it comes to machining and metal working. Nowadays I see so many people on the interweb KZreads that cut corners, force things, and sometimes simply just don't know what they are doing. Then they make videos and pass those bad habits on to others 😢. I also appreciate that you know how to correctly grind your own lathe bits which is something that all machinist should at least know how to do whether they use indexable bits or not. That is definitely a dying art. You are quite impressive my good sir, keep up the good work! 👍👏😊

@Mastermind-

9 ай бұрын

Thank you very much, my good friend, and I will try to offer the best as much as I can🙏🙏💐💐

@samhiscox3511

9 ай бұрын

@@Mastermind- good stuff Maynard

Witaj Fachmanie młody i najwyższy Szacunek od starego zawodowca, super robota!

@Mastermind-

9 ай бұрын

Dziękuję bardzo mój dobry przyjacielu🙏🙏💐

Do I understand correctly that first you release the metal (remove the quench), and then re-quench after processing? Cool work, but for those who have a welding machine or a heating furnace.

@Mastermind-

9 ай бұрын

You almost guessed right, my friend

@wellscody86

5 ай бұрын

Heated and left to cool to a anneal the hardened metal, then after it was quenched in oil that steals some carbon from oil for hardness but it quickly cools the steel to lock in the rearranging molecules.

Very well done. I keep in mind your way to sharpen a tap drill.

@Mastermind-

9 ай бұрын

Yes, thanks👍

Instead of the Three Jaw Chuck, you should use an ER32 Collet for better grip and concentricity.

@assyholey4224

9 ай бұрын

buy us all one.

@viejojorgge

9 ай бұрын

@@assyholey4224 A mí que me compre un macho como ese, ya estoy conforme...

The old way of screw cutting took skill and a sharp brain, it's scandalous how the salary of a toolmaker or machinest was so average for such a skilled job. Dying breed nowadays

Good video. I will try this method some time. Cheers Rob

@Mastermind-

9 ай бұрын

I am very happy my good friend cheers

Magnificent work.I need to make an m20 nut. I'm going to take advantage of the idea and do it with a 22 inch drill that I have in the workshop ... ( Not inches 22 m/m diameter )

@Mastermind-

6 ай бұрын

Go for it my friend

Very good idea, and better job ... i only ask how much oxygen was used, and how much would be instead cost a commercial tap ... ( of course not to deal with taps that are really "hard to find" on the market ... ). Note : a test with a blind bore would be much more relevant, as spiral taps are expecially designed for that type of holes ... Thank you very much in any case for your usefull lesson, i really appreciated both the heat treatments of common drills ...

@Mastermind-

4 ай бұрын

🙏🙏🙏💐

Nam știut ca din burghiu poate sa facă asa ceva tarod bravo meseriasule

@Mastermind-

9 ай бұрын

multumesc prietene

Now if you only had a twist drill that was left hand You could have the chips fall down Well done And I love the fact no crappy music Thanks

@Mastermind-

9 ай бұрын

Thanks my friend🙏👍

19:26 why this way? Use drill machine 18:25 for perfect coaxial hole.

Atelier propre, machines outil propre et enfin un travail effectué dans les règles de l’art. Je respecte et admire les personnes comme vous qui exécute des travaux frisant l’excellence, je remercie ceux qui vous ont transmis leur savoir et je ne doute pas une seconde que à votre tour un jour vous le transmettez à votre tour…… Cordialement

@Mastermind-

3 ай бұрын

Merci beaucoup mon cher ami et j'apprécie votre point de vue différent et j'espère que vous avez apprécié la vidéo🙏🙏🙏

Hello, have a good time, don't be tired, thank you for your good video, it was very good

@Mastermind-

9 ай бұрын

Thank you! You too! سپاسگزارم سانازگل

Pensa num cara treinado! Belo trabalho! Valeu muito obrigado!!!

@Mastermind-

6 ай бұрын

Muito obrigado meu bom amigo🙏

OLÁ. Gostei de ver. Acredito que o primeiro aquecimento foi para "temperar" a peça. A sugestão é a de um esfriamento mais lento colocando-a no mesmo recipiente porém envolta de grossa camada de "Carvão MINERAL". No final, a forma como foi feita a "CIMENTAÇÃO" é muito provável que a peça se torne 'QUEBRADIÇA". ABRAÇOS... Roberto Udo Krapf

@Mastermind-

4 ай бұрын

Olá meu bom amigo Muito obrigado🙏🙏🙏💐

Most TiN-coated drills are not real M2 or M3 HSS, so your tap is probably alloy. HSS is air-hardening, so it's very difficult to anneal.

@rameezsheikh7576

9 ай бұрын

HSS or Cast iron can be easily (not- really) Annealed by Submerging it into Limestone powder just after Reaching Red hot temp.

@VINOGRA

9 ай бұрын

Для HSS требуется температура закалки 1250 Цельсия. Это невозможно обеспечить газовой горелкой. Твердость будет маленькая.

@glennschemitsch8341

9 ай бұрын

This cannot be a cheap drill to start with,as some are just coated to make them look expensive.

@kieranh2005

9 ай бұрын

@@VINOGRA that is oxygen-acetylene torch which is up to 3200°C.

@arthurhuskins910

8 ай бұрын

@@kieranh2005 yes can reach those temps but this one was bearly turned on (still hot but not that hot)

Great job really! Only time I got was holding on to the part by hand during the drilling process. 🎉

@elisancere3578

4 ай бұрын

Worried*

@Mastermind-

4 ай бұрын

Glad it helped!👍

Good work. We shared this video on our homemade tools forum this week 😎

@Mastermind-

8 ай бұрын

Wow, thanks🙏🙏💐💐

Bonjour,quel beau travail. Très bien filmé. Mes respects 👍👍👍😉

@Mastermind-

9 ай бұрын

Merci mon bon ami et je suis si heureux que cela ait été agréable pour toi🙏🙏🙏💐

Спасибо. Идея которая лежит на поверхности. Можно изготовить метчик с направляющей. Его иногда так не хватает.

4:03 which insert are you using for turning???

Jak ja dawno nie ostrzyłem noża oprócz przecinaków do plastiku

Bardzo dobra robota!!!

@Mastermind-

9 ай бұрын

🙏🙏🙏💐

@NarinderSingh-bw9gv

8 ай бұрын

709

@KrugerdlyaMoisha-ce2xg

5 ай бұрын

Слышишь лях, а в где добрая работа??? Точность + километр -километр. .а цена 1 штуки 1 скудо.

Superb skills and hat off to someone’s that really deserve It.

@Mastermind-

6 ай бұрын

Thanks my dear friend

Just a quick question. Doesnt the reheating blunt the cutting edge of the tap?

@Mastermind-

9 ай бұрын

I don't think it has any effect, but to be sure, I resharpened the edges after reheating

@glennschemitsch8341

9 ай бұрын

no, he is now re-heat treating the tap as he annealed it at the start of the video.

Excelente trabalho e muito conhecimento parabéns

@Mastermind-

9 ай бұрын

obrigado meu amigo🙏👍💐

I'm already subscribe from some previous ridiculous video I watched of yours. Love the innovations!

@Mastermind-

9 ай бұрын

🙏👍💐

Can an Acme hand thread tap be made in the same way? Would any modifications to this protocol be needed?

@Mastermind-

5 ай бұрын

yes it will

Great job 👍

@Mastermind-

9 ай бұрын

Thanks for the visit🙏👍

Materiał zachartowany powinien być odpuszczony czyli jego twardość trochę się zmniejszy ale nie pęknie gdy przez nie uwagę spadnie, czy gwintowanie pójdzie trochę bokiem, lub inne sytłacje. Prosty sposób na chartowanie byłby taki jak zrobiłeś na początku. Grzanie jeśli możliwe całego elementu (najlepiej przez 1h) lub chociaż 30minut w szamot (cegły piecowe) i potem zachartować w całośći ale zostawić do czasu aż ostygnie w całośći. (Może w wodzie ale z dodatkiem soli (są osoby które dodają też sól do oleju ale efekt mi nie jest znany ??). Następnie czysty gwintownik wkładamy do piekarnika na 1h z tem 100⁰C (tu bywa różnie od metalu i odpuszczanie może być nawet w tem 250⁰C-ale jak dla mnie temperatura bezpieczna jest tem max 150⁰C. Tak naprawdę wszystko zależy od stali.) Czasami trzeba jeszcze raz włożyć do piekarnika po całkowitym ostygnięciu na kolejną 1h-100⁰C. Dobrym wyznacznikiem twardośći są koncówki (igły,szpilki wewnętrzne wtryskiwacza) i próba nabicia na główce małego punktu. Przy normalnym uderzeniu, głebokość punktu, lub uszkodzenie szpilki wew. wtrysku. (Sam czubek jest utwardzony . I nie polecałbym mocno bić młotkiem ,czy z boku gwintownika czy innego utwardzonego elementu). Na wpływ twardośći materiału ma też wpływ gaz jakim grzejemy materiał. ACETYLEN -powoduje że powierzchnia elementu staje się bardziej twarda !!!!!!!. Pozdrawiam

@Mastermind-

4 ай бұрын

Dziękuję bardzo za dobre informacje, mój dobry przyjacielu🙏🙏🙏💐

@piotrwaalk705

4 ай бұрын

@@Mastermind- ważne aby wymieniać się informacją ;)). Mam nadzieję. Że się przyda. Pozdrawiam i POWODZENIA 👍😉. I najlepszego na Te Święta 🎅🎅👝👝🍲🍲😀😀 i na nowy rok 🍾🍾🍻🥂🎉🎊☃️

@Mastermind-

4 ай бұрын

🙏🙏👍💐

Gran Bel Lavoro da professionista e con stile. Complimenti sei Bravissimo.

@Mastermind-

9 ай бұрын

Grazie mille mio buon amico🙏🙏🙏

Nice 👍👍🤝 Dear friend so amazing🌹☺

@Mastermind-

9 ай бұрын

Thank you so much 👍🙏🙏💐

Buen trabajo aunque pensaba, sí, en el costo beneficio. Pero es un trabajo artesanal a costa de ingenio , paciencia y habilidad. Es una satisfacción para el que lo hace. Vaya mis felicitaciones para Master y gracias por compartir conocimientos.

@Mastermind-

15 күн бұрын

Gracias por tu valioso comentario, mi buen amigo, y me alegra mucho que lo hayas disfrutado.🙏🙏🙏👍❤️

Bom trabalho que fez com a broca quebrada, parabéns

@Mastermind-

9 ай бұрын

Obrigado meu bom amigo e fico feliz que tenha gostado

Un artista!. Si señor

@Mastermind-

8 ай бұрын

🙏💐🙏

Parabéns pelo trabalho e pela organização e limpeza durante o trabalho.

@Mastermind-

9 ай бұрын

Obrigado, meu amigo Eu espero que você tenha gostado🙏

Complimenti!!! bellissimo e perfetto lavoro👍👋 Un saluto da Roma

@Mastermind-

15 күн бұрын

Grazie e sono molto felice e onorato che ti sia piaciuto, mio ​​buon amico🙏🙏🙏👍❤️

Sangat menakjubkan kawan. Hand trhead yang mantap

@Mastermind-

9 ай бұрын

terima kasih kawan🙏🙏💐

Ficou muito bom!! Parabéns

@Mastermind-

6 ай бұрын

Muito obrigado meu bom amigo

La pregunta es. Quien tornio las parte del primer torno creado ???

@Mastermind-

9 ай бұрын

No te pillo

@latinotvsa

9 ай бұрын

@@Mastermind- ósea quien hizo tornio las partes del primer tornó creado. Si no existia un torno

muy bien para fabricar machos de roscas poco comunes parece una idea genial, para roscas comunes no merece mucho la pena acabo de compara un M11x1 por 4 euros( igual solo hace una rosca pero va a cumplir)

Well done that man.

@Mastermind-

9 ай бұрын

Thanks my dear friend👍💐

Compla ali na China, balatinho né?😂 Excellent job, congrats.👍👍

@Mastermind-

9 ай бұрын

merci moninga na ngai👍💐

Schöne Arbeit, aber lohnt sich der Aufwand.

@Mastermind-

15 күн бұрын

👍👍🙏🙏

Super jest to pomysł pozdrawiam serdecznie 👍👍👍👍🏻

@Mastermind-

6 ай бұрын

Dziękuję mój dobry przyjacielu i bardzo się cieszę, że Ci się podobało🙏💐

I like what you did fella, but taps are not that expensive. But you did prove one can make it happen. Nice work Master Mind.

@Mastermind-

9 ай бұрын

Thank you for your opinion, my good friend, and thank you for watching🙏

@Bob_Adkins

9 ай бұрын

Correct, except for large high-quality HSS taps in odd sizes.

@victoryfirst2878

9 ай бұрын

@@Mastermind- I enjoy the show. Thank you Sir.

@victoryfirst2878

9 ай бұрын

@@Bob_Adkins Got it Bob.

@Mastermind-

9 ай бұрын

Thank you my good friend and I am very glad that you enjoyed it🙏🙏🙏👍💐

Exelente me gusto la idea grasias por compartir

@Mastermind-

9 ай бұрын

Muchas gracias mi buen amigo y me alegro mucho que te haya gustado🙏💐

Grand Travail, bravo 👍

отличный мастер молодец

@Mastermind-

9 ай бұрын

🙏🙏💐

How did you know how fast you need to rotate the piece and how fast to move the cutter in order to make the thread`?

@Mastermind-

5 ай бұрын

No matter how hard the tool steels are, they are still harder than normal steels and must be machined at a relatively lower speed.

very good job,thx!

@Mastermind-

9 ай бұрын

Glad you liked it!🙏🙏🙏💐

Why you applied heat before machining the bit??

@Mastermind-

6 ай бұрын

For reversibility and softening of machining angle

When you just have many cool machines.))))

@Mastermind-

9 ай бұрын

And when you have great ideas and machining skills😉

@Ma_X64

9 ай бұрын

@@Mastermind- Look at @Mehamozg. I'm shure you'll like it.

@Mastermind-

9 ай бұрын

I saw it and just👏👏👏👏👏

Молодец! Работа на высоком уровне. Продолжайте повышать свои навыки.

@Mastermind-

9 ай бұрын

🙏🙏💐

@papa58857

8 ай бұрын

Резьбу бы резать более полого на конус. Метчик будет так работать успешнее.

@KrugerdlyaMoisha-ce2xg

5 ай бұрын

Зачем заниматся целы день одним метчиком с очень низкой точностью, хуже китайских из 90х, если он стоит копейки, чисто хайпануть на восторженных дурачках, или если живёшь на северном полюсе в полной автономке.

Eso está bien saber hacerlo , pero si iba a una tienda de metal mecánica, y lo compraba, se hubiese ahorrado todo ese trabajo y hubiese gastado mucho menos😅😅

Muito bom excelente parabéns

@Mastermind-

6 ай бұрын

Muito obrigado meu bom amigo

Great video just a little note when lighting a gas tourch you should use a sparker instead of a lighter as the lighter fluid can have a blow back and cause the lighter to blow up in your hand

@Mastermind-

9 ай бұрын

Thanks for the info!🙏

@assyholey4224

9 ай бұрын

1million lights still hopping it blows me.

Все прекрасно. Мастер рукастый, но вопрос зачем? Метчик можно купить, а не тратить на это весь день

@user-hc6gb9oq9m

Күн бұрын

Работа занимает от силы пару часов, вполне адекватное решение, если нет доступного магазина инструментов.

Very Helpful and Informative video 👍✌️❤

@Mastermind-

15 күн бұрын

Glad it was helpful!🙏🙏🙏👍⚘️

Muito bom!

@Mastermind-

9 ай бұрын

obrigado meu amigo🙏

@taejin821

6 ай бұрын

나사 작업후에 탭 열처리 안해도 됩니까?

Genius!! The possibilites are endless!

@Mastermind-

15 күн бұрын

🙏🙏🙏👍🌹

Adamın dibisin kardeşim 🎉❤

@Mastermind-

9 ай бұрын

sağ ol, kanka Umarım eğlenmişsindir

@hayatsanayi1238

9 ай бұрын

@@Mastermind- hem eğlendim hem öğrendim eline sağlık

super good work !!!

@Mastermind-

8 ай бұрын

Thanks a lot!🙏🙏💐

Super podoba mi się

@Mastermind-

9 ай бұрын

Dziękuję, przyjacielu🙏🙏👍💐

круто , но уж очень заморочено . 👍

Shouldn't you grind a relief at the back of the flute thread?

@Mastermind-

6 ай бұрын

It's done my friend

Красавчик

The card is great, but the quality of your camera😢😢😢

That is my kind of recycling!!

@Mastermind-

9 ай бұрын

👍👍👍💐

@quincylui95

9 ай бұрын

Sorry, not worthwhile at all. Btw, you should use grinding machine instead of lathe to make thread. HSS steel doesn't need oil as a cooling medium. Liquidifed Corbin dioxide can work.

10:54 First time i see a SHCT… Socket-Head Cap Tap

Very good idea.

@Mastermind-

9 ай бұрын

Many many thanks🙏💐

Great 👍👍👍

@Mastermind-

9 ай бұрын

Thank you my friend 👍

Slick! Great video thumbs up.

@Mastermind-

9 ай бұрын

Thanks for the visit

Toll gemacht … !

@Mastermind-

9 ай бұрын

Danke mein Freund🙏🙏🙏💐

Very nice mate.

@Mastermind-

9 ай бұрын

Thanks for the visit

Bro i appreciate how clean you work ! Great job!

@Mastermind-

8 ай бұрын

Thanks for watching Thank you very much and I am glad that it was enjoyable for you, my good friend

HI !!!! FROM MEXICO !!!!! ME PARECE MUCHO TRABAJO PARA UN MACHUELO QUE PUEDES COMPRAR EN LA FERRETERIA POR POCO DINERO, THANKS BY SHARE

@Mastermind-

9 ай бұрын

gracias mi amigo🙏

Excelente trabajo🙏🤗

@Mastermind-

15 күн бұрын

🙏🙏👍🙏🌹

Bellissimo lavoro

@Mastermind-

15 күн бұрын

Grazie e sono molto felice e orgoglioso di te, mio ​​buon amico

Verynnice, but wasnit worth the time and money?

@Mastermind-

6 ай бұрын

There is more value for creativity and love than this, my good friend

@JonSpink

5 ай бұрын

You got value out of watching the video

GOOD STUFF 👍 THANKYOU

@Mastermind-

5 ай бұрын

Glad you enjoyed it🙏💐

Bravo Bravo Türkiye İzmir selamlar ve abonelik 🎉

@Mastermind-

9 ай бұрын

Merhaba değerli arkadaşım Eğlendiğine çok sevindim🙏💐

Carbon Steel drill - if you can find them these days.

How much is the price? I like it

@Mastermind-

4 ай бұрын

Free for you my good friend and glad you enjoyed🙏🙏💐

Sei in Italia?

@Mastermind-

9 ай бұрын

Non ora amico mio Ma voglio immigrare in questo paese con tutto il cuore E spero di incontrarti un giorno nel tuo bellissimo paese

@tuscanland

9 ай бұрын

@@Mastermind- Sarai il benvenuto, buona fortuna.

@Mastermind-

9 ай бұрын

🙏🙏🙏💐

Good work👍

@Mastermind-

9 ай бұрын

Thank you so much 🙏👍

Great teacher.

@Mastermind-

5 ай бұрын

Glad you think so🙏💐

Nice work piece

@Mastermind-

9 ай бұрын

Thank you so much🙏👍💐

Excelente trabalho

@Mastermind-

15 күн бұрын

🙏🙏🙏👌❤️

Сколько стоит метчик на 8 ?

Buona fattura però l'hai temperato troppo e i primi dentini si sono scheggiati subito e facevi fatica a filettare Comunque bel lavoro 👍

@Mastermind-

9 ай бұрын

grazie mio buon amico🙏💐