Bro I liked the Efforts taken for explaining that indirectly helped me Understand the Code

සුපිරි බන් 😍😍❤️

Hi brother I have done everything as you said but I have used 12v motor, whenever the ultrasonic sensor detects obstacle it stops, and it is not moving, could you say what's the reason?

Bro, I have connected the sensor with the 5v of the arduino . Now there is no 5v to connect the servo motor. Where will I connect it? And do we have to make any changes in the code?

Hello plz reply i have timline to complete the project ; Obstacle avoidance + Bluetooth control i wrote the code and everything but the problem is the hc-05 module keeps powering off after 5 seconds of pairing and i am using 2*3,7 lion battery why its not working? thanks bro

the code is just makingthe servo motor spin, it is not moving. any thoughts about the code?

why mine gust keeps spinning

What a nice toturial bro keep it up , how about pant car watering robot bro? . Using arduino water pump and others its moves when swith on and water plant target has low and dry soil using soil mosture hope you notice me bro

@RobotLk

9 ай бұрын

Ok I will try

@Codecode707

9 ай бұрын

I know you can bro , ill just wait and feel excited for your next upload bro that meant that🥰

@Codecode707

7 ай бұрын

Where is it now bro

Dont have 5 volt pin in my arduino I have 3.7 volt for ultra sonic sensor in my arduino uno italian version, it will work?

@RobotLk

2 ай бұрын

Connect the GND of the ultrasonic to the GND of the Arduino board, and connect the VCC pin of the ultrasonic sensor to the 5V out of the L298n motor drive.

@itsfact5541

2 ай бұрын

@@RobotLk where should i canaect the encho pin?

Bro i connect the battery then the holder was heated and l298n motor driver also heated?

@RobotLk

5 ай бұрын

There may be a problem with the motor drive.

make remote controlled car using l293d ND NODe 8266

The servo motor output latch is not spinning but sound is coming what to do

@RobotLk

3 ай бұрын

A problem of power. Are you using a 9v battery? Use both 18650 li ion batteries

bro please my motors are the same as urs however they do not have wires on them what do i do??

@RobotLk

Ай бұрын

Solder the wires in your motors as I have soldered the wires in the motors I show

@urnonexistentlol.

Ай бұрын

@@RobotLk ok thank u so much

Should we use 2 or 3 lithium ion batteries??

@RobotLk

3 ай бұрын

Use two batteries

Is it possible to program arduino from a phone?

@RobotLk

8 ай бұрын

Yes, it is possible

Can i use arduino uno italian version?

@RobotLk

2 ай бұрын

Yes

New ping library is not found... Its not downloading... Can u please help me to complete my project...

@RobotLk

8 ай бұрын

There is a link to download the newping library below the code on the website.

@RobotLk

8 ай бұрын

This video shows how to add kzread.info/dash/bejne/YoyTtZl7nK7LXbA.htmlsi=phku-r9c-3MJtg66

The sensor is working but car is not working the battery is fully charged 3.7V

@RobotLk

9 ай бұрын

Does the motor drive have the 2pin mini connecter?

Brother i completed all the connections and i connected the battery without coading, but as i connect it the smoke comes form Arduino 🥺

@RobotLk

4 ай бұрын

What is the voltage of the connected battery?

Okata bluetooth modular ekak hai karanna barda

@RobotLk

3 ай бұрын

Mekata ba.eka wenama hadanna ona. Bluetooth Control car hadana video channel eke thiyenawa

bro my one is not working ne side wheel is going forward and other side is going backward i dont know my servo is also not working its only turning one side

@SomaRoy-pb2ie

8 ай бұрын

The side going backward... Interchange that side wires on the l298n motor driver. If out1 has red and out2 black, make out1 black and out2 red.

Our Car Is Working But Sometime It's Not obstacle avoid. What is the solution?

@RobotLk

Ай бұрын

That's normal, You can increase the distance of the sensor with the code

Sensor working but car not moving bro what can do bro please

@RobotLk

4 ай бұрын

What batteries are used?

@sambanay4218

Ай бұрын

bro check your motor driver the enA and anB should be connected to each other

I got an error in the code

@RobotLk

8 ай бұрын

Add newping library

@Money_Gamess

8 ай бұрын

can you do it yourself please?

Bro sensor working properly but car not moving please help me bro

@RobotLk

9 ай бұрын

Must be a voltage problem.use two 3.7v li ion battery

I cant open link

@RobotLk

5 ай бұрын

An update on the website. Download the code and diagram from this link drive.google.com/drive/folders/1wozM3SPN-hYxvvB6o3apKNM7Bxq-s0aR

can you send me this code please

@RobotLk

8 ай бұрын

robotlk.com/how-to-make-arduino-obstacle-avoiding-robot/

6,7,8 වසරේ හොදම යාලුවා මතකද උබට.😁❤️

@RobotLk

11 ай бұрын

Na bn, අයේශ් ❤️

@RobotLk

11 ай бұрын

KZread channel ekak karanawada,

@kuttiproductions

11 ай бұрын

ou bn krnwa, shape ake

Bro i am usw 2 gear motars

@RobotLk

5 ай бұрын

No problem. It can also be made

bro motor not moving

@RobotLk

4 ай бұрын

What batteries are used?

Bro the code is not working

@RobotLk

5 ай бұрын

what's the problem

@user-qq8et9rl4c

5 ай бұрын

Bro it solved thanku bro

@RobotLk

5 ай бұрын

Welcome

sensor working but car not moving pls reply for this problem😔😔😔😔

@RobotLk

4 ай бұрын

What batteries are used?

@enjoyr3046

4 ай бұрын

7.4v battery @@RobotLk

the project is infeasible, the 4 volt hubby motor will take more than 12 volt in output, and you are just giving 9 volt in supply.

@RobotLk

2 ай бұрын

9v battery cannot be used. You can use rechargebale 9v battery. 9v battery amperage is not enough. Many people who have built using 9v battery have commented that it does not work properly.

@debabratadas9762

2 ай бұрын

@@RobotLk even if you will use 12 volt li-ion battery, it will still not suffice the voltage requirements. The output rating of 4 motor is more than 12, also you have to give power to servo and sensor. And you are using l298 instead of l293d

The sensor is working but the car not moved

@RobotLk

5 ай бұрын

9v battery is used?

@enjoyr3046

4 ай бұрын

7.4v battery bro @@RobotLk

Hi bro 1stly please respond to my query Ive used (L293D. Motor driver) Everything is fine I'm using 2 ×3.7 v cells but sensor is working but motor is not working please help i can give you my mail id if you want to respond

@RobotLk

6 ай бұрын

If l293d motor shield is used, the arduino code must be completely changed. I am using a l298n motor drive. The code I used and the circuit diagram do not match the obstacle avoiding robot made using the l293d motor shield.