Looks perfect. Best video l have seen yet showing how these work.

You inspired me to try this but I will be putting two clamps per spring

You didn't have to remove the front wheels?and why did it take you so long on the first wheel?and r they still holding up? Im asking bc im about to go get the same for my endeavor but im gonna do 4 on each coil..to make sure its safer..ok u do have to remove wheels

How Are the clamps holding up?

I did this on a 2015 honda civic and it made no difference. maybe the strut is preventing it from going lower?

How long do they last

Is it 14mm or 13 for the bolt

i used these before,my stock springs arent the cut type so had to put these,quick fun way of getting low..had no problems at all, 2 on each spring and you good to go,thats if you not racing or going over humps fast,tbh i enjoyed the bouncy effect

@Ricky50scJustalil6cylinder

5 жыл бұрын

Ohh yeah love the bouncy effect but also the car looks alot better

@josevelarde4113

5 жыл бұрын

henry vdub junkie so you used 2 clamps on each spring??? So it will be 8 clamps in total??

@hassangooner233

5 жыл бұрын

yep,,but mine were abit different than these but just dont drive over bumpy stuff too fast,and make sure you tight them hard,2 clamps opposite each other on one spring in a way that ey dont touch your car body if that makes sense,but wont get so low as cutting springs :/

@hassangooner233

5 жыл бұрын

and you might get em squeaky noises but i honestly dont care about that my sound system replaces that sound xD, i dont really drive fast,and makes my car look better,atleast for now till i find ways to cut my springs or save for lowering springs and cut them, and i took off my front springs to put them clamps on,just to be safe

@moeezirfan6900

5 жыл бұрын

@@hassangooner233 does this harm the suspension/springs? I am thinking of it because I just want my car lowered for a show. Suggestions?

Se ve perron keep up the good work

thats amazing and for so cheap! definitely doing this to my G5!

@EuroTrashTV.

Жыл бұрын

If you do this to a g5 upload a video I got a g5 and wonder how it would look

Well this work for a grand Cherokee?

How are they holding up any luck?

Looks so much better

Yes I am going to use this method for a temporary fix on level in the truck but yes it is true clamps for spring one on each side to evenly lower them down and keep the pressure the same time that you lower it so you lower one then you go to the other one you lower that one when you go to the other one you lower that one so on so forth. I wish you the best brother go buy yourself another set of clubs and redo it two clams per spring and yes Jack your car up on cement. Do not mean any disrespect I am also going to do the same thing on a 4 x 4 suburban Z 71 go on and let the comments begin for those off-roader freaks!

I put them on but i only had them go arojnd 2 springd u had them around 3 springs how did u get them to be like that

How does she ride?

good video, pls use jack stand next time youre working under your car

How was it when you install these clamps looks great I’m not trying to spend crazy money on some springs or coilovers how was the ride

@jedbeach5284

3 жыл бұрын

It'll be bad because the spring rates will be the same, but if it's for aesthetic then ig go for it

@automachinehead

2 жыл бұрын

@@jedbeach5284 as bad as stock?

❤️❤️❤️ Plz tell me that Can it brake spring or any rubbing on speed breakers Thanks ❤️

@Ricky50scJustalil6cylinder

3 жыл бұрын

No it wont brake ur spring

What kinda car is that

Where did you bought that lowering instrument

@edwardmartin4068

2 жыл бұрын

Autozone has them

These clamps can change the driving caracteristics from car. And when you load the car and the wheels drop in potholes the moved around the coils??? Answer me plz because I want to instal to my car!

@Ricky50scJustalil6cylinder

6 жыл бұрын

Anstasis Golf2 you dont have to worry about the clamps moving aroung the coil because no matter how much weigh you have in the car the coil never compresses all the way. But you will notice a different handling

@user-gu4mj6pk1

6 жыл бұрын

Ricky 5.0s/c οκ thank you

Are the clamps safe and won't break when driving at 40-60Mph?

@automachinehead

2 жыл бұрын

driving 60mph on potholes will destroy any sedan with or without the clamps

I have those exact rims MR142’s

Where did you get the product?

@edwardmartin4068

2 жыл бұрын

Autozona has them

isnt better to use two jacks one to raise the car up and the other to raise the whole suspension using jack under the rotors, with wheels off? i said this because it had to be hard to screw the clamp screws the way you did it

@Ricky50scJustalil6cylinder

5 жыл бұрын

Yeah bro that would be a better idea😂 I never though of doing that

Bro did this on my 2014 kia forte sedan, on the rear dropped it everything it can go with the clamps but it hits hard on like bumps or something it that supposed to happen or did i do something wrong?

@baylertolman9910

3 жыл бұрын

It's bc ur spring rate is still the same witch meas that ur car thinks it at stock height so the weal will try to travel the same but lowering springs are stiffer so it don't do that I just rides a little harder

@deep7889

3 жыл бұрын

You need to cut your bump stop. Its the yellow/black cushion thing. U need to do that when u lower your car in any way including this way.

is this safe?

What’s the best way to remove these

@backyardburnouts8846

3 жыл бұрын

Angle grinder

Anyone knows the easier way to lower a x5 bmw. Could i heat the coil springs ?

@gbodysbc

4 жыл бұрын

Horace Samuels don’t ever heat springs. If you must, use clams but 2 on each spring 180* from each other

@horacesamuels2052

4 жыл бұрын

@@gbodysbc thanks alot i havnt do nothing yet due to covid 19&20 .but i was thinking to buy drop springs but i cant see the right ones to give me that 1"drop at the front.im only seeing 1 1/2" .

How long did you have these on your car for ? Asking for a foo ?

@Ricky50scJustalil6cylinder

4 жыл бұрын

Had this for like 2 months

So I’m thinking about doing this to my Mazda 3 to drop it slightly like 05” to 1”maximum using 2 clamps per spring, you think I should do it? How do you feel about it to lower the car slightly

@sethschlientz2000

3 жыл бұрын

I’m not all to sure on doing it this way I got a 2017 Mazda 6 and want to lower it the same amount but using just clamps unless it’s some kind of high grade unbreakable steel it looks like it could break shoot off on a wrong bump and with all the force of the coil break shit.

I have the same car and i got some 18's as well & was thinking of using this same exact method, what's your take on it ??

@Ricky50scJustalil6cylinder

6 жыл бұрын

Raul GARGOLA Rivera if you dont care how it rides then go fot it. the car bounces all over. What i did instead was to cut the springs. i think it rides better than stock now and it looks really nice.

@GARGOLASPERFORMANCECOATINGS

6 жыл бұрын

Full Throttle how much of the spring did you cut and was it from the bottom or the top ?

@GARGOLASPERFORMANCECOATINGS

6 жыл бұрын

Full Throttle thanks for the update !!

@Ricky50scJustalil6cylinder

6 жыл бұрын

Raul GARGOLA Rivera you cut from the bottom. And it also depends on how mich you want to lower the car. Message me on instagram i can show you pictures of how it looks now.

@Ricky50scJustalil6cylinder

6 жыл бұрын

This is my instagram ricardoboumrad

Where did you get these clamps at? I need to get some for my car now. Great video

@e.tgotvintage602

3 жыл бұрын

O’Reilly’s auto parts

You put one on each side or two

@sivel5589

5 жыл бұрын

Jose Velarde both. Other wise one side would be regular and the other would be lowerd

Nice 👍🏼

Hey so I used these and I still have a huge gap but I’m afraid of tightening more because it’s getting hard to turn did you encounter this? And do I turn more?

@Ghost5.4

3 жыл бұрын

I wish someone was nice enough to respond to this because I'm still looking for an answer💀

@AB-rs1qh

3 жыл бұрын

Will be hard just keep goin

@deep7889

3 жыл бұрын

You can lift up the suspension by jacking from the lower control arm to your desired hight. Then remove the wheels and tighten the clamps. Make sure to put red lock tight so it doesn't come off.

@BadTV1993

Жыл бұрын

@@deep7889 you can also dab a bit of silicone where the clamps sit on the spring so you wont get the scrapy noise from them slightly changing position

Did u use 1 clamp on each spring or 2

@Ricky50scJustalil6cylinder

5 жыл бұрын

2 on each spring

@sugestive371

3 жыл бұрын

@@Ricky50scJustalil6cylinder does one pack come with 4 in it ?

@Ricky50scJustalil6cylinder

3 жыл бұрын

@@sugestive371 2 on each pack

@ronnydisalvo80

3 жыл бұрын

They still holding up?

@Ricky50scJustalil6cylinder

3 жыл бұрын

@@ronnydisalvo80 nah bro i got them replaced like 2 months after for lowering springs lol it felt like i was riding in a trampoline

Wait but I would imagine the car would sit crooked if you don’t tighten them all evenly

@mudzy9820

2 жыл бұрын

tighten the shit out of each one thats how you know ahaha

@okcerx

Жыл бұрын

@@mudzy9820 another way is to measure or count how many threads you’ve gone on each side, bouta do this to my Camry, i know the dangers but tbh it’s a camry and it’s MINE.

How many clamps did you place on each sides?

@Ricky50scJustalil6cylinder

6 жыл бұрын

2 for each wheel

Is this safe to do?

@Ricky50scJustalil6cylinder

3 жыл бұрын

I dont see why not . I got coilovers about 3 months after that

Is this safe 😳??

My GAWWWEEED THAT FUCKIN MUSIC 😮😮😮😮😮JEEEEEZUSSSS😊

Hey where do I buy the lowering clamps ? Thanks get back to me

@Ricky50scJustalil6cylinder

4 жыл бұрын

Autozone

How does it ride?

@Ricky50scJustalil6cylinder

6 жыл бұрын

1973primetime hi the car looks nice but it rides pretty bad it bounces all over when you go over bumps😂😂. i just cut the spring 2 weeks ago it looks nice and it rides better than stock. You should just buy lowering spring and if you dont want to spend alot of money just cut your spring way better than this clamps

Bro, is that second wheel missing a whole ass wheel stud?? wtf

Does it rub ?

@Ricky50scJustalil6cylinder

5 жыл бұрын

No rubing

@marsaylus3466

5 жыл бұрын

What size wheels and tires do you have and did you lower it 2 inches or 1

@Ricky50scJustalil6cylinder

5 жыл бұрын

@@marsaylus3466 1 have 18x8 with 225 tires an yeah about 2 inches lowerd

Bro you need smaller wheels

What happens if you driving & one of them pop?

@EhvoOnGo

3 жыл бұрын

worst case the car moves back to ride height on that side

@seanhill1164

3 жыл бұрын

That’s it?

@sirenz_

3 жыл бұрын

Don’t listen to Ehvyn, if one pops, it will force the spring to its “normal” form, and with the amount of force bc of it randomly popping will cause force to the wheel and it’ll most likely cause you to lose sudden traction, and then you’ll lose control. Don’t even use these stupid ass clamps. They’re dangerous.

@fraided88

3 жыл бұрын

@@sirenz_ Equal to hitting a pothole or a speedbump. It won't make your car fly to the moon if it breaks.

@Immad1337

3 жыл бұрын

@@sirenz_ you're an idiot. It will simply return the wheel to stock height. It won't break anyway, considering they're made from mild non-hardened steel. There are NO cons to running spring clamps. The only thing it hurts is your feelings for some odd reason.

Nevermind I'll stay quit on this one

bro this is. dangerous

Dude, you really need to buy some more tools. Maybe a ratchet and some deep well sockets.

just get coilovers at this point bro it would be so much easier💀

@purkeyy4019

Жыл бұрын

we’re poor

@anthonymacaluso1488

Жыл бұрын

get real, coil over installs take alot longer and are probably 10 times the price

@BadTV1993

Жыл бұрын

@@anthonymacaluso1488 facts

@DragSlicks

Ай бұрын

For my car coilovers are anywhere from $2k-$3.3k bags are $4k-$5.4k lowering springs are $800-$1.5k but only bring you down 1-2.5 inches so I said fuck it and cut my springs and it’s actually smooth as fuck actually the same if not less bouncy😂

When you forget that that spring rate is a thing, and you use these stupid things that shouldn’t even be a thing.🙃 Sure it lowers the car super cheap, but it’s dangerous.

@goathimself5613

3 жыл бұрын

Compression of a spring is dangerous but only when you compress them enough. Do you know Forsure what happens if one malfunctions or do you have a prediction? I bet none have malfunctioned for someone to know. But everyone has they own way of thinking

Damn thats not safe foo

@aguevara557

3 жыл бұрын

Idk foo

🇵🇷😎👍

This is the most ghetto unsafe shit you could possibly do to your car.

Bet they make creeking noises. Don't be a cheap bastard and get some good coilovers

@Ricky50scJustalil6cylinder

3 жыл бұрын

Callese alv

And these shitboxes drive on the same road as my 80 thousand dollar alfa romeo giulia

@Ricky50scJustalil6cylinder

9 ай бұрын

😂😂 yes we all drive on the same road. Dont be surprised when u get smoked by one of these shitboxes😂 u drive a slow car

why tf do people feel the need to put on gay ass christmas music sounding like shit on their videos like damn makes me not wanna watch it cuz i dont wanna watch it muted anways

So much wrong in one video. This us why youtube needs to bring back the dislike button.

How does it ride ?

@Ricky50scJustalil6cylinder

5 жыл бұрын

It rides bad😂😂 it bouces all over lol

@marsaylus3466

5 жыл бұрын

Ricky 5.0s/c really, I just got mine in the mail today to try out. I’ve got a 2010 genesis 3.8, idk how it’s gonna go

@Ricky50scJustalil6cylinder

5 жыл бұрын

@@marsaylus3466 I bough coils for mine last year and it ridea better with the coils

@marsaylus3466

5 жыл бұрын

Ricky 5.0s/c thanks for the help bro

@Ricky50scJustalil6cylinder

5 жыл бұрын

@@marsaylus3466 no problem bro