How To Install & Wire Auxbeam Switch Panel, Fuse Block, & Driving Light
Автокөліктер мен көлік құралдары
Install and Review of the Auxbeam AR820 8 Gang Switch Panel and fuse block as well as a set of V-Series 5" Driving lights w/ side shooters and DRL's. This video will show you how to install and wire an Auxbeam Switch panel as well as how to wire a pair of driving lights to the switch panel and fuse block.
(These are affiliate links - no extra cost to you, but I do get a commission on qualifying purchases)
Buy an Auxbeam Switch Panel Here: shrsl.com/4e7d7
Purchase Auxbeam V-Series 5" Driving Lights: shrsl.com/4e7dd
Other Tools Shown in the video:
As an Amazon affiliates/associates member, I earn referral fees on qualifying Amazon purchases.
Rivnut Gun + Nutserts (Similar): amzn.to/3SfLO6j
Soldering Gun: amzn.to/3u8VozG
Heat Gun: amzn.to/42mO547
Longer Battery/Power Wire: amzn.to/3Sy2lnc
Wire Stripper/Crimper: amzn.to/49aHPi5
Ratcheting Screwdriver: amzn.to/48TUHcH
Nilight Bar Clamps:amzn.to/3Of6zhi
Electrical Connectors: amzn.to/42mO547
Wire Loom: amzn.to/3vNEZ4d
Extra Wire for Lights: amzn.to/3OiDMZ4
Grommets: amzn.to/3SwBWq3
Drill +: Impact: amzn.to/42hkyZE
Heat Shrink: amzn.to/3Sdobep
Knife: amzn.to/496Ho8v
Battery Terminals: sdhqoffroad.com/products/sdhq...
Пікірлер: 25
Thanks for putting this together. The most comprehensive video I’ve come across.
@208Tyler
4 ай бұрын
Thank you! I appreciate it.
Excellent tutorial. I will be picking one up. Also those SDHQ terminals. Thanks!
@208Tyler
Ай бұрын
Awesome! Glad the video helped
still missing the r50 content. i still go back and look at your posts when i have questions :’)
@208Tyler
4 ай бұрын
I appreciate it man!
This is great content 👌🏼 will need to order this kit asap! You lost me on the DL splicing. But I’m sure I can figure that part out.
@208Tyler
3 ай бұрын
Thanks! Do it. Just needed a “ignition-fused” source for the DRL, so I used the same wire that powers the switch panel (the one that tapped the fuse in the interior). It worked great!
Thank you for this video, very informative!
@208Tyler
4 ай бұрын
Thanks! Glad you liked it
Great video, It's exciting to see the next episode
@208Tyler
4 ай бұрын
Thank you!
Great video, buy some automatic wire strippers! They’re worth every penny, trust me!
@208Tyler
4 ай бұрын
That would be nice! Might have to get some
Love the Tacoma🔥
@208Tyler
Ай бұрын
The tundra? Thanks!
@markwillmsen9679
29 күн бұрын
Bro so thought that was a Tacoma but I also didn’t watch the whole video
Nice!!
Quick question, I’m new to this, how did you know which amp fuse to use for these lights? You used the 30amp fuse I think correct?
@208Tyler
Ай бұрын
You can do math to guess it. A 30A fuse on a 12V system will work for up to 360 Watts of power (Power = Amperage * Voltage)
Question - When I ran the SwitchPro9100 on my old truck, say to some rear bumper lights, I was able to ground the lights on the chassis at the back of the truck and simply run 1 hot wire up to the control box. As the Aux Beam box has both + and - terminals for each switch....do you HAVE to run the second wire (ground) up to the box or can you leave that open and just ground the accessory on the chassis somewhere? I've looked fro the answer, but no joy. I liked only having to run 1 wire to the SwitchPro box vs 2 wires (if required) to the Aux Beam. Or perhaps you can combine all of the grounds from the box to a single ground near the box..and ground the accessory at the location where it's mounted. I suck at electrical things....not sure if you experimented with it.
@208Tyler
11 күн бұрын
Ground is ground. So run it to the box or to the chassis, both should work
@benjaminharvey2229
11 күн бұрын
@@208Tyler Thanks man...just ordered it. I just wasn't sure if the ground from the box not being...ground would cause an issue. Much appreciate the reply.