How to install these pesky Teflon seals. Ford power steering line seal
Автокөліктер мен көлік құралдары
Fords are known for using this type of seal. it works excellent when installed correctly
#keepwrenching #wesselmotorworks #wrenchingwithkenny
power steering leak power steering fluid Ford Focus ZX2 Focus ZX4 Focus ZX3 Fusion Seering pump rack and pinion rack & pinion fluid leak
Пікірлер: 30
The snap on socket seal/washer tool got have one! Fomoco approved! Great tip!
Thanks, good tip! I was tired of seeing my line leaking on my serpentine belt.
Kenny thank you so much for posting this video it help a lot
You can the same thing with a sharpy cap, difference is a sharp cap will slip over the threads nice and easy and the seal slides right on!
Great tip!. I just made the mistake of putting a Cardone pump on a 09 focus which lasted all of two weeks.Was second guessing if I installed the washer wrong.Second time around will be a proper pump and this trick.Thanks!
Thanks Kenny Great info
Great Job Kenny ...Oscar from Colorado @ 68 years
Great problem solving idea. I would have tried soaking the teflon washer in warm water about the same temperate as a hot cup of coffee. Making it more pliable.
@northpoint1039
Жыл бұрын
I was thinking the same thing. Of course, I would have probably got mad and put some rubber washer in there. That way I can spray steering fluid all over my driveway and tick off the wife. :)
Bravo old mate that was a trick werth learning Fantastic great job 💯👍
@WrenchingWithKenny
4 ай бұрын
I appreciate your reply. Thanks for watching & keep wrenching 🔧
@Bok2022st
4 ай бұрын
@@WrenchingWithKenny truly was my pleasure I have an FG Falcon have not had one but the man before changed the power steering high pressure line. But now that the car is mine the power steering pump is making a crappy noise I like put oil behind it it's quiet four little time and also when I took the cap off it made a little pop sound but with pressure in the oil tank I'm going to leave the top off and turn the steering wheel left and right a few dozen times hopefully get the air out of the system and then I'm going to figure out how to take some pressure off the belt. Maybe too tight live and learn I guess. Cheers mate will keep watching
@WrenchingWithKenny
3 ай бұрын
It's doubtful that the belt "being too tight" is the problem. I suggest a powersteering flush. It may solve the issue for you 🔧
Good tip. I wonder if a heat gun might allow it to expand a little to allow installation.
@WrenchingWithKenny
Жыл бұрын
Quite possible
@californiadreamin8423
Жыл бұрын
@@WrenchingWithKenny. Hi from across the pond and my Transit nut onto the power stearing pump. This nut also has a seal on the internal diameter , so there is potential for 2 leeks to occur. Yes you’ve guessed….I have both !!
I watched ford Tech Makuloco channel and all he did was stretch it with his fingers and installed one thread at a time until it seated at the bottom. Also Rich Pin Channel used the cover on a sharpie to install the seal.
we put in water and put in microwave then stretch it be hand works great
I use a “lady finger”.. or tapered alignment bar. It works well as well.
@WrenchingWithKenny
Жыл бұрын
Good idea !! Ill try that next time
I went to Ace Hardware and got a 11mm viton o-ring. The nylon seal from Autozone broke.
Why can’t I find this Teflon seal o ring for a 2012 Ford Taurus. I can’t find it anywhere
Do you know where I can get these
Can you use brings better
Could you heat it up..heat gun...boiling water ..??
@WrenchingWithKenny
Жыл бұрын
I would think hot water would help. Ive never actually tried it that way
The size of the seal?
@WrenchingWithKenny
5 ай бұрын
I don't know but I believe Ford only used 2 sizes. They are both in a kit available at the parts store. Usually, it's a "HELP" pack. I hope that helps. Keep wrenching 🔧
Fords, no wonder the company is going tits up. Smart arse dady boys get to design big boy stuff
@70ixlr86
16 күн бұрын
Flare and nut just wouldn't work? Like say, it did for 40 some years?