Dry ice would be the best way to take the undercoat off and it’s really good cleaning anything

Bodyshop owner here . Strip undercoat by heating and scraping . Once you get the bulk off thinner cleans it up great or if you dont have any brake cleaner or wax and grease breaks it down .

Y’all need some S1 in your life, he fabs all that AWD eat up and he does some of the best work out there

Please undercoat the entire Tim next time. I would buy a pair! 😂😂

Kevin did it. (Glizzys)💯🔧🚗🏁®

I love that you constantly ask him, "what are you doing?". I don't know much about the AWD setup so I am curious and you ask pretty much for a novice who just watches videos and didn't grow up with any knowledge about cars.

The S1 built billet carrier bearing mounting bracket for the wagon you wouldn't have to cut that lil section out.

Bro this shit so clean and jroc legitimately goes hard asf. Dude really cares about his craft fr

Keep cleaning the wire wheel after each pass on a 2x4 spray some wd40 or brake cleaner the wood should clean the wire wheel

We make a one-stop-shop full front to back AWD kit as well, simple to install, no extra custom parts needed, straight forward set up.

Damn that's a lot of work. Good stuff! the glizzy stenciled on the tims is hilarious.

This video !! Straight fire feels like I’m there with yah especially laughing to 😅🤞🔥

Crazy y’all brought up fueltech u just got mines installed with the jumper on my stock k24. Got a k20z3 head going on now and just got in touch with Jaime for the tune 💪🏽 love the content bro been watching for some time now appreciate what ALL of y’all are doing for the Honda game 🫡💯 continue fucking these guys up👍🏽

Air craft remover is the best thing to strip basically anything to bare metal in just a few minutes. Also try easy off oven cleaner.

For the Undercoating: Get yourself a heatgun and a spatula. Its tedious, but I did my whole wheel houses that way :D

YES!!!! This is the shit I love!! Step by step!! Grinding, scraping, you guys cut this video together very well with the work you did! Thanks so much!!

Great job guys jrock be killing it.

To remove the undercoating use a propane torch and scraper. You don't want to burn or melt the coating you just want it to heat up and become softer. You can go to home depot and ask for a 5-n-1 tool which is in the paint aisle. It's a type of scraper with 5 uses (different shapes to scrape in different ways). You can also use a 1000watt-1500watt heat gun. Use acetone to wipe off any residue after. Acetone is a good solvent to use for prepping surfaces for weld. Removes a lot of types of paint, wax, grease, oil etc. As far as the actual welding. You would have much better success with dual core Flux shield wire. The Flux in the wire constantly cleans the metal and pull the contaminants to the surface of the weld puddle. Dual shield is commonly used for structural metal welding like buildings and the metal can actually be welded in a fairly rusty state without having to be cleaned prior. Using solid mig wire and 75%/25% mix isn't a good idea with something as dirty as that undercoating sub frame

Finally a long video. Thank you 🙏🏽

Wow just hands down amazing 👏

i want to see it all boys! and you guys are a hoot!

Great content...dope video

Jroc for president

More of this videos please!! fire video

Love them matabo cutting disk

Dry ice blaster would knock it out quick. Not sure what kind force the viscous puts on the actual frame but switching the plates 180° where the overhang is on the notched side might help rigidity

Y’all for sure explained it right and did it right 👌🏼

Undercoating - fire and wire wheels. Takes about 10 sec to remove Driveshaft length would be hard to make across the board. Their are too many variables involved. You would have to make like 100s of combo. Also you don't have to notch the tunnel with the S1Built billet carrier bearing because they are offset upward. In all off our videos we never had to notch the tunnel.

@sonic_203

Жыл бұрын

going to try them for the next build for sure, thank you!!

Love your work gents. Thank you for these videos. It’s very helpful. God bless

Y'all all killing it homies maybe time to start looking into fabrication. Maybe the next chapter in your story. Love the content fellas keep hustling!

Nice video thanks!

Mickey Andrade and the dudes from Throtl made that Front engine RWD EK named the FREK.. it's unique af but idk how well driveability/reliability would be

Would love to see more on how the rear diff, axles, rear hubs, and rear suspension is done on the awd setups. I’ve never seen a video done on that part of an awd build before.

@obezzyjohnson9680

Жыл бұрын

U can go to boosted boiz n they do it on there ek hatch when they did the awd setup

Stepping on his boots after spray painting them 🤣🤣🤣🤣

I had Goodluck with dry ice and then after the ice I put some aircraft paint stripper and then scraper or pearl pad on a grinder.

Saludo desde PR 🇵🇷🇵🇷🇵🇷💪🏽💪🏽💪🏽💪🏽🔥🔥🔥

i love so much this channel you guys are awesome keep the great work i would like so much you guys to tune my ep3 k20 but you are far away!!

to get the undercoating off, definitely heat gun on high, and a putty knife. That will get most of it as long as the surface is -relatively- flat or uniform. Then take some Xylene to it with a stainless steel pot scrubber (chore boy) I've had good luck with this.

i was gonna like this but i dont like the number that its currently at atm. but this is a great vid with good info. here in nz for it to be street legal we’d probably have to go extra and weld in those plates crush tubes so it goes all the way up into the floor, then have through-bolts with an extra plate and nut on the end.

🔥🔥

You guys build high quality shit!! I would love to see you guys build a ek 4dr hatch with a G23 h2b and rbc manifold…

Damnnnn🔥🔥💥💥🤑

I’m betting in the next few weeks s1 another company’s maybe even ktune lmdao will have them brackets made ready for sell lol

@sones1built196

Жыл бұрын

It been out for years now. S1Built billet carrier bearing and billet carrier bearing brackets doesn't need to notch the tunnel. They are offset upward.

U shld look into making ur own parts and take ur brand an ur boys 2 the next level

Loving the vids guys. Keep ‘em coming. It is about time someone does a detail install of this👏. Question, does the angle of the driveshaft from the diff to the viscous coupler matters? From the vid, it seems that the driveshaft from the diff has a downward slope to the viscous. Would appreciate it if you guys could go more into this aspect of the install. Thanks.

@sonic_203

Жыл бұрын

it has a downward slope

Kev did it not JROC 🤣🤣🤪 remember that 😂 Great vid I always watch all the way through very entertaining… Y’all had me dieing laughing painted the new tims because your brother brought brand new tims to the shop 🫡🤣

The people at S1 built just heat the surface 1st with torch then hit it with wire wheel comes right off watched them do it in real time

Kev did it 😂

Looks super clean so far !!!

Looks like it's possible to shorten the ends of that front carrier bearing bracket, drill new holes and move the bolts and then you wouldn't have to notch the frame

The reason you're able to break a factory camshaft is because it's made from a casting. They pour liquid metal into a mold. If you look at the ends where the cam fractured you will see the metal looks like small grains of sand. There's no uniformity in the grain of the metal. If you tried to do that with a billet camshaft you'd more than likely hurt your hand and chip the sidewalk. But the cam wouldn't break. It all has to do with the metallurgy and science behind how the metal is made. You could also break a cast cam shaft with a specific sound frequency at a loud enough volume level. Kinda like how you can shatter a glass with a speaker making a specific sound frequency. I've been a machinist for 20 years. So I've learned a lot about metallurgy and castings over the years.

Diablo flapper discs, I remove vinyl from sc40 pipes all the time it takes a good amount of pressure, but I would assume it could take care of some undercoating.

Crazy that it takes that long. I took my car to the people who changed the game with the best awd kit HUB CITY PERFORMANCE & it took less then two weeks to get everything done even make the driveshaft, mount the vis with mountain the diff basically everything. Even the price was great. I had called you guys like 3 times & left my info & you guys never called me back sucks because you guys are literally like an hour away. I drove all the way to Maryland because everyone that I called had some excuse about taking the work in.

@sonic_203

Жыл бұрын

it took that long to get Aluminum drive shaft or carbon, Im very sorry, we are slammed atm especially with H day coming up! Agreed hubcity is the best

Air scraper is what you need. Harbor freight sells them for cheap.

Yeah I remember when I made my eg awd it sucked doing it in my driveway took me about 2 weeks

Yoo SONIC Yea boosted boiz had the fluid changed in there viscous IN THE VAN changed to a better fluid n they had the clutches in viscous changed in it n it ripped it's ass off. Get up wit Kyle n ask him about the fluid for the viscous Sonic.

best removal for the under coat is gonna be a dry ice blaster.

Arron with the h22 awd ek has something on his rear driveshaft that basically disconnects off a pull of a lever and it makes the DS FREE SPIN so its fwd

Mr.Clean magic eraser will do the trick

💪👍

Paint stripper in the undercoat with a little heat and a scrapper Unless you have an Infinti AEM they pretty much have stopped support for it Link Ecu is a very very good unit but none of them have the display/all in one like FT

@uknterror508

Жыл бұрын

Also love the sort of walk through yall did with this!

You guys need to spray paint a 🌭on the intercooler

i fawkng agreed with that driveshaft concept. It needs to be a Mainstream Oem Honda aftermarket placement part with 1310 joints and chassis specify. so people can just but the driveshaft and slap it on.. I then it'll be a Good business Opportunity for NewEnglandRacing to come out with Those concept Parts for AWD. i'm down for it. because I have 2 different sets up right now on hand for a 92-95 Eg hatch/Ej coupe chassis with Awd K series motor(k24a2) and trans( crv trans) and b series(b18c1) motor and trans(crv rd1). A freelander with Crv rear and a Wagon full driveshaft and rear.

S1 built does it all one stop kit

Dope build. What brake lines are those?

Throtl did a rear wheel drive ek hatch with a k20 motor

Jroc innocent till proven guilty in the court of law

Dry ice ( which I guess isn’t “terrible “ on pricing to get the machines )… but if your doing it at home soda blasting it is way more convenient and easier to set something up and blast.

@swift__

Жыл бұрын

*Asked a friend since he’s done it more so then myself….dry ice works better then soda blasting because your freezing it but either way apparently your going to go thru a ton of it to get the coating off. 😔

Lol, they’re definitely brothers. 😂

hmmm have u try paint thinner cause under coating just a style of paint

Aircraft Stripper to get the undercoating off

🌭🐐🐐🌭

You guys make templates and I can make those plates for ya.

Kev did it

Bro if you can find some way to get some dry ice to hold up against the bottom it would come off so easy

I’m curious as to why you guys don’t look into S1 built awd kit.

Sp tuning made his awd crx rwd

Ef rails are the real nightmare to do this on 😭

S1built make billet AWD components

What viscous did he go with so that you don’t have to cut much?

I'm looking at those weilds but I'm guessing he's weilding to 22 gauge steel.

Is the Viscous coupler the same as pinning the clutch pack for a locked differential?

Heat it up

Dry ice or oven cleaner should work.

People been doing that with the audi quattro.

How’s ground clearance with those brackets sitting so low.?

Freeze under coat with keyboard cleaner?

use goof off for undercoat

First

Down side is until it is refined everyone is the test dummy Another 5 years & I recon it will be a direct bolt up kit

Try some air craft stripper

Ice blasting

Use paint thinner with a brush

Ice

Brake cleaner !!!

S1 KZread channel

Not the glizzy timbs

Is that the stock wagon viscous coupler? Have you tried the AKD or Gear-X one??

@sonic_203

Жыл бұрын

yeah with new fluid

Portable media blaster from harbor freight

Heat gun and a scrapper/puddy knife