Good job Bro🤘

This is exactly what I was looking for. I have the very same table saw and, needless to say the very same accuracy problems. Gonna watch carefully. Thank you!

I put a new top and fence on mine, I scribed a line right across from the blade as a reference datum. I also used a over centre clamp and French cleat system on the fence -all work well.

TC TS 2025/1-U Nekem is ilyen van, és ezek a hibái. Nagyon jó videó, sok embernek segít a probléma megoldásában. Én még szereltem bele "soft start" elektronikát, mert nagyon dúrván indúl, nagyon megterheli a fogaskerekeket. 👍👍

@robertkeresztes1758

2 ай бұрын

Szia! tudnál esetleg segítséget linkelni ehhez az elektronikához hogy hogy smint stb? én kb jobban félek a bekapcsoláskor mint vágáskor:D tényleg durván indulnak

Don't forget your riving knife! Make room for it on your new zero-clearance cut. Using the table saw without it is asking for trouble, as you probably know.

Ha, just the model i was looking for! Thank you!

👏👏👏👏

I have a table saw exactly like this. I have been worried about its Accuracy. Thank you for the video, I can't wait to see how you make a fence, a sled and other accessories

muito top

I learned more about how to use tools from this guy than I would watching 12 other videos!

@HandmadeCreativeChannel

Жыл бұрын

Thanks for the comment 🍀👌👍

@michaelbrowne8469

8 ай бұрын

Very careless with the angle grinder, if that slipped his todger was gone

When you seen one hole drilled you've seen 'em all.

Very good idea. I want to do the exact same. Thank you very much for this video. Kind regards from germany.

Good idea and execution but a very bad quality of the plywood used., it would be better a phenolic plywood.

Can you make a video please with "how you can align the blade to this type of table saw??"

I'd sooner go to work earn a days money and buy a better saw in the first place 🤷🏻‍♂️but that's just me

One thing you should never do is on your first pass go so deep? You will burn your router bit out in know time.

Should never ever ever go full depth on your first pass with a router

@mitch3384

Жыл бұрын

Agree. It should never be at a depth where you have to force it through a cut.

Jjrlamas its not plywood if you look careful at the wood chipings you will see it is chip board.

@darlioliveira5765

6 ай бұрын

E um aglomerado isto logo esfarela aí trabalho perdido mas quem não tem cão apela pelo gato

nice, only problem is that you lost some cut depth.

@HandmadeCreativeChannel

2 жыл бұрын

Yes, but it's also 5cm deep.

Bad Idea useing chip board will warp in time as it will draw in dampness. Far better use good ply wood..

Why would you want to put a chipboard top on machine

@Wen6543

Жыл бұрын

It´s cheap, bigger area, you can screw fences, etc. for special projects and warp problems are practically insignificant. The original tops of this cheap machines are too thin so they can warp too much ruining even the basic cuts and the only option is to replace them.

@andrespeary2202

Жыл бұрын

Personally I would have gone with plywood, that would have been a better option in my opinion, but if its not readily available to you then I think you've done a good job using what you have 😊

chipboard is the worst possible material to use as a table top...it will absorb moisture and warp ....you are wasting your time

@walterpickford3204

Жыл бұрын

It won't matter . He can always use the garden / coffee table. It's already predrilled.

Seriously just buy a better saw!