This is such a good way to make an instruction video. Your explanation is the best I've ever seen on this topic.

@RicardoLino

5 жыл бұрын

🙏🏻🙏🏻🙏🏻🧡 thank you soooooo much

@xblumentopfx

3 жыл бұрын

i agree

@Sketchmedic

2 жыл бұрын

@@RicardoLino hello good sir, so I’m looking at doing doing this for my FR3s, now you said to put the insole in first yea? So I’m a 271mondo (10.5 / 45) 11/11.5US normally. With your super feet I saw you have there, I’m curious if you have space between the end of the insole to the footbed/toe end in your boot like I do if I took my insole out of my liner and put it underneath? Wouldnt this cause you insole and foot to move around once you get to sweating in there? Would you recommend taking the glued in insole under my liner? And replace that with either my gamechanger or a super feet (I think they have lower profile)

Very inspiring video! We do this because it's fun! I am excited to try this out with some F2's where the lining is taking a while to stretch!

Hi Ricardo. I really enjoy your video's but i'm not into in lines ( yet } ... I've been skating on quad's for year's and i'm getting better.... Skating for me has been an absolute joy but I've had to over come life threatening injury and illness, my legs - left arm - shoulders are all full of pin's, plates, screw's and staples... Hopefully once i've got my full confidence on quads i will give in lines a go. But until then thanks for making these awesome video's

I appreciate all your videos man, keep going!

@RicardoLino

5 жыл бұрын

:) thank you. i really really appreciate it :)

Another good tip instead of cutting a liner just wear thicker socks when you put your foot in. Worked really well for me.

Hi Lino, I didn't understand the meaning of this thing but I bought a PS Fatboy liner, for pain in the malleolus, and I got the confirmation, you don't need a hot modeling liner, but a hot modeling boot.

In case anyone would like the written instructions by Intuition, you can find them here. They apply for Intuition Skate as well as other Intuition liners for skii boots: intuitionliners.com/home-fitting/

Thanks Ricardo! Just bought some Intuitions, but I don't have a microwave oven... does it work in a normal oven?

All my skates have Myfit liners. I'm interested to see if that works for them.

Yo moldee mis botas intuition v2 con un secador de pelo y perfecto! 💪😜

Hi Ricardo, the tongue of the intuition liner causes a lot of pain in my shin. Is that normal? ANyway to avoid that? Thanks man!

Do you think the Intuition liners are the best liners you have seen

How about using a hair dryer?

Super super helpful. Tried it myself and it made a huge difference. I have two questions though: 1) Can you heat mold the liner multiple times? 2) What is the difference between putting the insole between the boot and liner vs replacing the intuition insole? I just ordered some superfeets. Thank you!

@RicardoLino

4 жыл бұрын

Thank You!! You can do it multiple tines and I usually put the insole outside to that it does not change the original height if the liner. Ut that's just me. Best is depending on the skate playing with it and see what feels better. 👊🏼

@vinsongotingco5753

4 жыл бұрын

@@RicardoLino Thank you for the reply! I'll definitely try both. What kind of insole do you use? I ordered Superfeet Carbons. So if I put the insole between the boot and liner, I'm wondering if the plastic heel of the insole will break, if I land too hard, since it will be up against the boot.

One question, the insole under the linner????? I only changed the insoles once, and I puta some USD honey comb but i put those inside the linner....

Hi Ricardo, perfect lightning and audio, but my question is something that you have probably forgotten! For how long do you need to keep your feet inside the skate meanwhile they are molding the liners? Regards mate! And keep going!

@RicardoLino

5 жыл бұрын

thanks man. usually, you let them cool down... i would say around 10minutes should be ok :) thank you for the feedback.. its really important:)

@hansbrommer3143

5 жыл бұрын

You’re welcome!

Is that the intuition dream liner and is the thinnest volume. Lots of people say Roces need thin liners??????

Did you use the microwave on full power ?thanks

Hey guys, if I put the size small intuition V2 liner (Foot length: 25-26.5 cm Liner size: S Shell size: US 7/EU 40) into a Medium US 9/10 sized THEM 909 skate, will the liner wiggle and move around in the THEM shell? Would the liner be too small for that shell? Thanks in advance!

I just got my V2 in the box. I was wondering if I could skate them without heatmolding. At least to try them out at first. FYI FR1 boot here.

@RicardoLino

3 жыл бұрын

Yes for sure. They are awesome but a bit hard at first.. this was just to make them more my fit quicker but most people don’t heat mold them

@cubul32

3 жыл бұрын

@@RicardoLino thanks Ricardo, reddit came to my help as well: I found out it's wise to heat just the toebox area if the liner fits well (it could generate more unwanted space). Google-fu gave me this info: heatmolding reorganizes the foam (like dough) filling in the spaces and keeping the foam soft, while breaking in pushes/presses the foam in and cam get hard spots in the foam.

did someone try this out with a myfit liner? How did it work? Last time trying to heatmolt my liner the myfit way, i messed it up absolutely.

Very interesting (and wierd with rice xD) BUT! Whats up with that shirt of yours? It has the dreamcast logo

Ricardo how long do you leave the rice in there before you switch to your foot?

@iSmiley.

3 жыл бұрын

He said 5-7 mins

Hi Ricardo, I saw that the top part of your m12 looks like widen up, I mean the space between the eyelets. Did you work it out like that? Because back in the old days I had to cut down all around the eyelets and make new ones, there was too much pressure on the top of my feet, let's call it the horn of the foot

@art0nblades

5 жыл бұрын

I have that problem with my Razors Shift 2... :-( Somebody told me to heatgun the area and ply it back, but I'm a bit anxious to try...

Axel te ama

The microwave company is watching. That 10 year warranty isn't going to be honoured. Hahahahahah

^^nice vid and a sweet wife btw.

Anyone know if you can heat mould the new reign v3 HT

@TheGrumbliestPuppy

3 жыл бұрын

Google

So does it fit better now ? I've just bought intuition liner and use it with imperial supercruiser. For now, it kind of hurts, like if my feet were too wide even if they are narrow !

@RicardoLino

5 жыл бұрын

well i didnt had any problems before but the foams do feela bit softer.. like if i skated them for a month or two

"I wanted to eat mold" I love auto-subs :D

What temperature?

@cuestaabajoysinfrenos.1826

11 ай бұрын

It's said (written) in the video.

What liner is that between the intuition and wheels ?

@jaylow759

Жыл бұрын

Do you mean the insole or the skate boot (plastic hard boot)? If insole: it's SuperFeet Yellow and they are really great, i'm using them myself.

The rice method seems like its be easier but could you so it by foot heat and naturally break em in?

@AndyRipley42

5 жыл бұрын

This may not be super helpful since mine are only a week old at the point of writing this (maybe 4 hours spent skating). I haven't heat molded mine but I can tell you they're starting to form to my feet more. They stretch quiet a bit as well.

What if I fave heat moldable insoles? Inside or outside the liners? Should I buy biger insoles if I put them between boot and liner?

3 жыл бұрын

Should be inside, according to Intuition. Detailed in step 9 of their home fitting instructions PDF. To be inserted in the liner when putting your foot inside the heated up liner. See intuitionliners.com/home-fitting/

I just burn my liner , 200 dollar in trash