No one else has explained this to me so straightforwardly. Thanks!

I actually like reprogramming the AR636 and have no trouble getting them to do what I want them to do. It was FlightEngr on RC Groups who figured out how to reprogram them and provided the software that we use. It is a little easier to set up the Smart AS3X/SAFE receivers with Forward Programming, but a person still needs to understand how a gyro works.

@dennishallman7783

Жыл бұрын

Are older 636a and 636b capable to forward programing

@txkflier

Жыл бұрын

@@dennishallman7783 None of the AR636’s support Forward Programming..

@ItAintMeBabe99

3 ай бұрын

Please make a video explaining each page and what they mean in Telemetry.

Thank you for the video

Thoroughly enjoyed your NX six transmitter help, I just upgraded to a NX eight, I wish you would add comments for higher channel radios in your NX six videos

Thank you for this video! You have certainly answered my question as to why I could not find the forward programing function on my DX 8 Gen 2. transmitter.

I had no idea the dx9 would do it. Got one used couple years ago just left it on the shelf until I saw this video. Had to register and update the dx9 but it works 👍thanks so much. I have quite a few rxs from bnf planes laying around you probably saved me few hundred bucks.

@GRIFFINRCPLANES

Жыл бұрын

That is the whole point of my you tube venture. Glad that helped

Another useful video, Thanks Sean.

I have the older gen 1 . I was able to bind it to my aeroscout which is the rtf version. I was able to get safe to work, still unclear on expo settings on different rates as far as sensitivity. Your videos always informative!

@txkflier

Жыл бұрын

On the AeroScout, the expo and rates are set up in the receiver by Horizon.

Great vid! Helped me navigate my new NX-8 You are awesome!

Thanks Sean.. Amazing video as always 👌

Thanks for an interesting and informative vid. I am new to Spektrum and have been using aftermarket recievers but recently purchased an AR630 for a new build. It was worrying when I couldn't find Forward Programming on my DX7 while I was reading up on how it worked before installation. The instructions weren't clear that it had to be bound and on before the F P menu showed in the main menu. Your explanation cleared my confusion. Thank you. 😊

Does the spektrum dx6e not able to do forward programming?? I'm losing my mind after updating both the radio and the receiver (ar631). Can't figure out what I'm doing wrong.

@c70char

2 ай бұрын

Same here. Have you found anything?

Are older 636a and 636b compatible to forward programming? Do you have a video on how to do forward programming . Step by step. Thanks

@GRIFFINRCPLANES

Жыл бұрын

I do have several forward programming videos. HOWEVER THE AR636 does not use forward programming it can only be custom programmed by using the AS3X PROGRAM APP OR THE PROGRAMMER ON A COMPUTER

Thank you for your vids New to spektrum NX10 and all is a great help.

My issue I’m having is my dx6 g2 won’t read a single sd card I have. Not sure what else I can do? Any help

Can you answer me a question?? when you are setting up your transmitter and when it comes to aircraft type one wing and one aileron screen or other options, on the wing type screen and then you click down next and it shows that screen and it shows to activate 3 position gimble should you in that screen activate it that on the new receiver setup or not and just leave it alone? and then when you click down on that screen it asks what type of picture you want for your aircraft. you know what Im saying bud? Id like to know if I should set the 3 axis gimble to active on that screen on a plug and play receiver?

It seems like my DX8e will have forward programming. Not sure if I need to update it or it will be there once I'm bound to my 8063T receiver. We'll see when it gets here. Thanks for good videos, keep it up.

My Aeroscout rtf has ar631. I just got a dx6 gen2 and updated it to 2.08. Whenever I follow directions to bind it with safe and reverse the aux1 channel, I get 2 different safe modes to the switch I set for gear channel (B) but I can’t get safe to turn off and I have almost zero elevator. If I switch aux1 back to the same as other switches in reverse menu, I gut full elevator travel but no safe and only as3x. When I hold panic button with aux1 reversed, it turns safe off and has only as3x active. I try enter forward programming and it says connection failed. Any suggestions? I’ve been trying to figure this out for over a week now.

👍👍

Show us how to setup Safe Select please. I have the DX18 and a AR8360T receiver. Can't figure it out!

I have Dx6e and ar630 and forward programming wont show up at all

@AlpineCorpus

3 ай бұрын

Same boat haha

@c70char

2 ай бұрын

​@@AlpineCorpussame here

@AlpineCorpus

2 ай бұрын

@@c70char I got it to work by updating the firmware to one of the older builds, I think 2.07, then it popped up when I bound my 630

@mastaajbomb

2 ай бұрын

Same here just bought them new and updated the dx6e. No forward programming

@c70char

2 ай бұрын

Good News!! turns out version 2.10 doesnt work, but reverting back to 2.9 makes itwork@@mastaajbomb

I have an nx8 and sport cub with ar636. When I select forward programming it says connection failed. Help please

How about how to program AS3X settings to any plane...thanks

Jesus Christ brother get to the point LOL. That was a long video I think it was about five minutes longer than it needed to be.

You did not talk at all about how to program one of these receivers. I guess this video was intended for something else?

My gosh, we don't need a history lesson, get to the info man.

8 minutes of utter garbage rabble to get to a 4 second simple explanation

@BubbaB43

10 ай бұрын

Damn, was somebody holding a gun to your head making you watch the whole 8 minutes? I could have swore there was a fast forward and next button here on KZread 🤔. I think it's hilarious when I see grown ass men crying about something so petty. Notice your the only one complaining about the video, that should be your first clue who the real problem is here!

If you unlock your ar637ta then you get forward programming. But the open stock ar637t is unlocked from factory and forward programming is available..