❤ If you liked this video, 🙏 share this video with your friends 📈 it will help the development of the channel! ❓ ask your questions

Excellent video. Thanks for not talking / playing music / doing a ten minute rambling intro / talking about sponsors etc. I’ve serviced my bottom bracket based on your video and the difference is amazing. I know a new unit wouldn’t break the bank, but there is something satisfying about keeping things going.

Very nice to see you repair things instead of just throwing away. 40 years ago when I worked in a bike shop, we had a solvent tank to clean parts. The tank makes it easy to get all the grit out of the parts.

This is the way real mechanics do things !

My noisy year old BB is now clean and well lubed. Thank you for this tutorial

@NiceBikeService

3 ай бұрын

Thank you for your comment! 😍 if you liked this video, share this video with your friends ❤️ it will help the development of the channel! 📈

I can't help subscribing you because there are plenty of bike building videos but not many bike maintaining videos, but I prefer maintaining than buliding. And your videos are so well-made!

I just completed installing one of these bearings on a very old Giant brand Canyon bicycle. I just bought a new bearing. It was pretty inexpensive and was very simple to install since I had the proper tools. I just saved myself some money.

@NiceBikeService

7 ай бұрын

✊👍👍

7:03 the important thing is to make the right noise when torquing-up ;-) Good video, thanks!

Good for the planet and will work for some time like anything else so great work.

Konuyu çok güzel tarif ettiniz. Teşekkür ederim. 👍👏

Wow you are amazing, impressive work and thank you so much!!!

👏👏👏👏👏 Gracias por compartir este excelente video.

Nice! Very good job 😎

Very cool your video, thanks for sharing knowledge. 🇧🇷

Parabéns! Muito bom. Att Bazoti Brasil

Great job.

很不錯的影片,一般4方軸bb都不修了,因為零件很便宜,都直接換新的了

Otima dica amigo

Ich hatte keine Lust und habe auch nicht das handwerkliche Geschick, alles auseinander zu schrauben. Ich habe auf gut Glück am Tretlager und am Übergang von der Pedale zum Rad alles mit gewöhnlichem Sprühöl geölt. Ich hätte keinen Pfifferling darauf gesetzt, dass es was bringt, aber siehe da, nach vielleicht 10 Pedalumdrehungen beim Losradeln war das Knacken zu 100 % weg. Vermutlich pures Glück, dass das bei meinem Kreidler-Fahrrad funktioniert hat, aber man kann es ja mal versuchen! 😀

@NiceBikeService

Ай бұрын

Ich danke Ihnen für Ihre Geschichte. Das Öl aus der Dose ist eine vorübergehende Lösung, in Zukunft müssen Sie entweder reinigen oder ersetzen Sie das Tretlager

Good video

Been watching your vids and liking 'em. I was curious as to what cleaner you have in your little pump bottle and the type of grease you use?

Otimo trabalho amiga

Teşekkürler

@NiceBikeService

5 ай бұрын

hizmet verebildiğimize sevindim! geri bildiriminiz için teşekkürler 😘

thank you

Sweet!

Dziś wpadłem na ten filmik, a dwa dni temu szlag mnie trafiał jak wymieniałem suport. Pomyślałem, że mam jakiś klucz do suportu do dupy. A tu patrzę na patent ze ściągaczem do korby. No maksakra. Dzieki :)

Parabéns pelo vídeo. Aqui é do Brasil

@NiceBikeService

8 ай бұрын

Obrigado. Bem-vindos ao nosso canal, desfrutem do vosso visionamento.

@user-kh6zp8pt4k

8 ай бұрын

Thật tuyệt vời cám ơn một video bổ ích.

@NiceBikeService

6 ай бұрын

Cảm ơn bình luận của bạn! Hãy chia sẻ video này với bạn bè của bạn, nó sẽ giúp ích cho sự phát triển của kênh! 📈😘

full support idol 🙏 God bless 🙏 very nice 6👍🚲🙏

I wonder opinions. Would it be nice to apply grease to any screws on bike prone to dust in order to unscrew easier later on?

No grease on cranks, you bended the aluminum and the crank going loose after some kilometer. The bearing was the same destroy like before 😂

@Reflec999

Жыл бұрын

Grease on cranks 😂😂😂😂😂

b dias es necesario requintar el ajusto del eje pedalier gracias

Fajne filmiki. Oglądam wszystkie 🙂. Z centrowania by się przydał filmik 🙂.pozdrawiam i dużych oglądalności życzę

❤❤❤❤❤❤fantastisch

Bonne vidéo pour qui connait le sujet. Il faudrait préciser que du coté gauche ( manivelle simple ) c'est un filetage pas à droite et du coté droit ( manivelle avec les plateaux ) c'est un filetage pas à gauche donc sens de dévissage inversé par rapport au sens habituel. Les vieux vélos des années 1970 et moins ont certaines fois des pas à droite des 2 cotés. Personnelement je coince l'ensemble cadre avec son axe monté plus l'outil de démontage à l'étau juste pour le premier tour de dévissage pour être sur de ne pas riper et endommager les cannelures qui si elle sont en plastique ne survivent pas à 2 ripages. Si les cannelures de démontages sont foutues il reste la méthode de scier le plastique dépassant du cadre le plus possible d'un coté, de caler le cadre sur du bois et de frapper sur l'axe jusqu'à son extraction. La douille plastique vissée de l'autre coté étant facilement détruite en place sans endommager le cadre. La réfection montrée est faite sur un type assez rare de cassette ( les plus légères soit dit en passant ) et qui sont démontables en un axe central plus 2 vrais roulements mais de dimension difficilement disponibles dans le commerce ( Ø 16 Ø 31 x 10 ) plus un tube entretoise entre les roulements. Pour le remontage il est bon de visser un peu chaque coté avant de bloquer le coté droit en premier puis le coté gauche. C'st en tout cas une très bonne vidéo, bravo.

Buenas tardes, veo en tus videos que usas un aceite verde no grasa, ¿es el aceite usado en la refrigeración automotriz?, porque se parece mucho y es bastante fino, ¿Es mejor usar ese aceite que usar grasa?

Bike repair ASMR 😂

@NiceBikeService

9 ай бұрын

🐱

I agree with most comments and critiques, but nevertheless you have a new subscriber :) Are you from Eastern part of Europe ?

Que bonito

@NiceBikeService

Ай бұрын

Obrigado pelo seu comentário! 😍 se você gostou deste vídeo, compartilhe esse vídeo com seus amigos ❤️ isso ajudará no desenvolvimento do canal! 📈

سبحان الله وبحمده سبحان الله العظيم سبحان الله وبحمده سبحان الله العظيم سبحان الله وبحمده سبحان الله العظيم

Bonjour, merci pour votre vidéo et le partage de vos connaissances ...est-il possible de connaître le type de graisse que vous utilisez pour refaire les roulements? merci et bonne continuation...🤘🤘🤘

@eljudge6

10 ай бұрын

Ok, merci 👍@@NiceBikeService

Hello nice video !, can i ask what kind of grease do you use here??? Im gonna try it with my bike , thanks!

@2869rajendra

29 күн бұрын

Please send grease brand name and buy link

What grease and cleaner spray liquid did you use?

Out of curiosity, what grease tool is this? And what grease are you using on the bearings? It looks really high quality!

@NiceBikeService

9 ай бұрын

Thank you for your feedback . This is an ordinary syringe + nozzle for flux or glue. You can find them in electronics stores and Chinese markets. For lube, we use thick calcium grease Divinol

Nice hammer, bit jealous ❤

Quel liquide utilisez-vous pour le nettoyage merci

I didn't know BB can fix!! It doesn't need exchange,does it?

Leva a mal não mas o serviço não foi bem feito dessa forma a sujeira continua ainda o certo é retirar todo rolamento tô do eixo lavar e lubrificar os dois lados... existe uma forma correta pra sacar o rolamento só quem tem as manhas é que sabe

Yo solo pude quitar un balero sellado ,el otro pacere está "pegado" con el eje pedalier

👍💪

Коти прикольні 😸🙀 в сльозах та істериці.

Well Done. What lubrication are you using?

@hendrikgraser40

Жыл бұрын

@@NiceBikeService Thanks

Good job! We share hobby

Hocam full süspansiyon dağ bisikletine press fit göbeği çıkarıp, bu karemil göbeklerden takmak istiyorum. Uyumlu mu?

@NiceBikeService

3 ай бұрын

Hem kare hem de standart pres geçme için bir alt braket bulmanız pek olası değildir

@canorak4801

3 ай бұрын

@@NiceBikeService sizi Türk sanmıştım :)

Could you link to the tool you use at 0:23 to lock the bracket wrench in place?

@NiceBikeService

3 ай бұрын

This is a craft tool that is made by a person in their own workshop to order. Try searching for "Shimano Hollowtech II bearing pressing tool"

Try lubing a hollow pipe bb. Progress is often regress when it comes to bike tech

Friends, please tell me what size square tapered bottom bracket for Giat Atx 27.5 (68×117?)

@NiceBikeService

Ай бұрын

You will know the exact size only after measurements, only the manufacturer will be able to tell you the exact size of the bike, and even then it is not accurate

Доброго дня, у вас чудовий канал! Тепер обслуговувати велосипед стало набагато краще. Одне питання: де можна замовити "чудо гвинт" який закручується в каретку коли викручуєте чашки каретки?

@mazepa437

Жыл бұрын

Дуже вдячний, ви супер!

Note, this is only 1 out of dozens of types of bottom brackets. Make sure you know what type of bottom bracket you have and how to properly remove it or you could end up damaging both the bottom bracket and your frame.

⚠ ❓ ⚠ *ASK YOUR QUESTIONS* 👇👇👇

@grader32

4 ай бұрын

what's the brand of the grease you use, the green one?

Ведешкою з балончика можна бризкати у підшипник для очищення від старої змазки?

a lot of mistakes, bearings to be replaced immediately, you can’t knock with a hammer, only a puller, clamped the thread with a vise, well, you can’t guys

Hi idont have any specific tools for bottom bracket what should I use….

@NiceBikeService

29 күн бұрын

Hello. You can find inexpensive tools on Chinese marketplaces

What about a clunking bike? The clunking is happening in the bottom bracket, as I'm pedaling, and on the non-drive side. It happens on the downward stroke, but only on the non-drive side. For now. What's going on?

@NiceBikeService

4 ай бұрын

The bearing in the lower bracket on the left-hand side is probably damaged. Oddly enough, bearings on the non-drive side fail faster

LOOOOOOOOOOOL le pédalier carré !!!!!!!!!!!! LOOOOOOL

that was delicious to watch

@NiceBikeService

3 ай бұрын

Thank you for your comment! 😍 if you liked this video, share this video with your friends ❤️ it will help the development of the channel! 📈

Where did you find that tool that holds the socket on?

@NiceBikeService

4 күн бұрын

If you mean the vice, we found it at a flea market

@markemery7741

4 күн бұрын

@@NiceBikeService I was referring to the tool you put in the end of the pedal shaft after installing the socket. Is that just to keep the socket on tight?

Quiero saber el nombre del sprai que limpia y que tipo de grasa es su nombre por favor

O ideal seria tampar com massa epoxi os buracos de acesso que levam a caixa central e fazer um pequeno furo para escoar a água próximo a numeração do registro.

das hübsche Bike muss liebevoll behandelt werden!

I have a creaking noise on the left pedel ,i tighten the bb but no use... Pls suggest a solution

Those bearings sounded rough at the end and don't think you are supposed to grease the square taper BB crank interface, it's supposed to be a dry fit.

@stan1845

Жыл бұрын

Hahaha same thought here, they're still crunchy. Greasing the taper is common here in the Netherlands cuz rain, rust and frustration 😂 if there is no place for the grease it will be squeezed out anyway :)

@stan1845

Жыл бұрын

@@NiceBikeService I totally agree with you :)

@BradCagle

Жыл бұрын

I grease tapers, just don't over tighten, and split the crank.

@kaixinzhang5259

Жыл бұрын

@@stan1845 you should grease the place or using copper compound. To prevent seizing. Also to let the crank be pushed into the spindle smoothly. It will not cause the crank to come loose. U just need to to torque the fastening bolt to 40Nm

@pastapizza7370

Жыл бұрын

@@NiceBikeService ???

i want to know where you get that bolt to hold the bb remover did you made it yourself or bought it?

@TimJorden506

Жыл бұрын

@@NiceBikeService ohh alright thank you!

@zedtony8110

8 ай бұрын

It's m8x1.0 thread

@TimJorden506

8 ай бұрын

@@zedtony8110 thanks dude even though I already made one this still useful

What's the name of the Green lube you're using?

@NiceBikeService

8 ай бұрын

For lube, we use thick calcium grease Divinol

He's making that little white cat CRY! Why?

@NiceBikeService

28 күн бұрын

😿

Отлично 👍

@batkamahno1991

Жыл бұрын

Что за смазку юзает? Литол пойдет?

DO you use regular syringe available inpharmacy ? WHat is the green grease you use?

@NiceBikeService

28 күн бұрын

Yes, it's an ordinary syringe from a pharmacy, but it has a nozzle for glue or flux from a hardware store. Green grease is Divinol thick calcium grease

有中文解說非常好，可惜是.簡體字幕，有繁體字就更好👍

Those bearings were finished, they should have been replaced. They are very cheap. Far too much torque from that bar. Also you shouldn’t knock the bearing into the cup like that. I could go on.

@avva4090

Жыл бұрын

​​​​​@@NiceBikeService although I believe King Aldo is correct, and in your situation I probably would have just got a new BB and kept the old one until I could get new bearing cartridges to restore it, sometimes the jury rig is all that's on the menu, 🤷🏾 and there's nothing wrong with that. If the bearing cartridges get ruined you can just put new ones in, you're probably not going to crash because your BB bearings/races are flat spotting/pitted lol. At least this way they'll be quiet 😹 Props to you for putting service footage on YT. That's right up there with putting your welding out there: follow best practices or you better have a thick skin and humility in equal measures.

@zdravo4

Жыл бұрын

Exactly, you can hear how they grind

@Jacksparrow4986

Жыл бұрын

​@Avva even if you follow best practices you need hard skin :-)

@Reflec999

Жыл бұрын

Yeah my bike parts are made of marshmallows and I ride my bike on pillow tracks. I could go on.

@williamdarico2369

Жыл бұрын

The bearings are steel they hold up fine no worries

znakomita robota, chociaż patrząc na zużycie tej korby można by już było ją wymienić na nowszą 2x z zewnętrznymi łożyskami :)

@davidburgess741

Жыл бұрын

It's very strange, but my bike has threads in rusted poor condition. The bike is a rare classic. Early in its life, the one side of the shell was thread Italian which has the same pitch but deeper threads. That side gave me problems before rethread. The other side is the original English thread. This is possible if you thread Italian from the tap with correct thread direction. Phil Wood retaining ring with Italian thread one side, and English on the other. Classic road bike with modern looking crankset, Noooo! It's a 45 year old Dave Moulton with hand written receipt by the man himself! It has some modern upgrades, but leave my "Movemento Centrale" alone!

@konradpopowicz3457

Жыл бұрын

Eee tam myślisz że każdy jest fanatykiem i perfekcjonista swojego roweru?

Porque no lo desarmo completo..para limpiar bien.los baleros.

@NiceBikeService

5 ай бұрын

Sí, también puedes hacerlo.

Pues no que no se pueden arreglar los ejes sellados?

@NiceBikeService

5 ай бұрын

Puedo))))

Hi. After disassembling and reassembling it, there was a play. no matter how hard I compress. Hmm..

I think you should use anti seize instead grease

What grese used?

@benjleath9406

Жыл бұрын

Where did you get the luminescent green Grease from ??

What type of grease do you use please? 4:37

@NiceBikeService

8 ай бұрын

We use thick calcium grease for lubrication

Just fit a new unit for about £15, or fit new bearings for about £15 from SKF .

@NiceBikeService

7 күн бұрын

thanks for the advice ! 😘

Bonjour je suis a la recherche d'un boitier de pédalier Mercier, largeur de boitier 68mm, axe carre 118mm. La cuvette fixe un pas a droite, cuvette réglable a gauche a droite . Merci beaucoup en avance de votre aide 👍

Hi

Po takim wybijaniu łożyska nadaje się ono tylko do wyrzucenia.

@NiceBikeService

3 ай бұрын

Dziękujemy za opinię! 😘

シールドベアリング自体は交換しないのですね？

What grease do you use?

@NiceBikeService

6 ай бұрын

shimano grease if you liked this video, share this video with your friends ❤️ it will help the development of the channel! 📈

@thegoodguy44

6 ай бұрын

@@NiceBikeService Would Shimano Dura Ace grease work for all this stuff?

@NiceBikeService

6 ай бұрын

you'll have to ask for details

Amigos este eje de cuadradillo no vale la pena engrasarlo y menos si hay juego Radia como en este caso la grasa lubrica pero no corrige el desgaste Además es un Repuesto de bajo costo. Mejor no le pierda tiempo y póngalo nuevo

@NiceBikeService

4 ай бұрын

¡gracias por el consejo ! 😘

There’s no way to revive bottom bracket bearings. Replacing only bearings is also senseless, because they are unique dimensions and expensive. Buying new bottom bracket is the only economically justified way (10$ for cheap one).

Дренажное отверстия было бы, такого срача не было бы! И Кот 😸 довольный был бы😊

@NiceBikeService

Ай бұрын

😹

Todo muy bien hasta que usas una palanca tan grande para apretar

@elrusso22

Жыл бұрын

@@NiceBikeService no es necesaria la llave con la misma carraca ajustas a tope y listo esa palanca es muy grande te puede llevar la rosca

@elrusso22

Жыл бұрын

@@NiceBikeService excelente pero nunca es tarde para aprender y seguir mejorando y seguir aprendiendo es la idea y tener más clientes para darles es mejor servicio

👍💯🇨🇺

che grasso usi?lo spargi con una siringa se non sbaglio ...

Reparar eje pedalier? Ni de broma! Compro nuevo y lo cambio..🙄🙂

@NiceBikeService

4 ай бұрын

¡una buena decisión!😺

There should be people who clean there bikes with a high-pressure cleaner.

En mi país cuesta 60 pesitos la pieza, es mejor cambiarla

@NiceBikeService

7 ай бұрын

Sí, pero el punto del video es el servicio