This might be some Jank stuff we did but hey if it works it works
Жүктеу.....
Пікірлер: 325
@solojoe11932 жыл бұрын
Helped me out bro I wasn’t gonna mess with my Buick cause it has rod knock but today I learned that it only takes about six or seven f***s and a little work and I can get this done 😂..preciate ya bro
@Nasperformance
2 жыл бұрын
What Buick you got and what size motor is it
@solojoe1193
2 жыл бұрын
@@Nasperformance 2003 park avenue 3.8L
@earthbros6508
Жыл бұрын
Don’t forget the liquid courage 🍻
@c4r5on882 жыл бұрын
Nice to see that having tourettes has not stopped him from doing the job he loves. Great work.
@abdulalhazred4589
2 жыл бұрын
Yeah, tourettes, the champion's illness.... 😆😸😆😸
@c4r5on88
2 жыл бұрын
@@abdulalhazred4589 that explains why I'm currently not a champion then. I need to swear more 😂
@Usaamah_Haarithi
Жыл бұрын
Lol
@joeo1725
Жыл бұрын
I won't use this video while my childs around.
@Junglist619000
8 ай бұрын
He sounds like a 5 year old that just learned curse words
@latedriver9019 Жыл бұрын
I wouldn't call this jank at all dude this is a work of art.
@blazeandcyrus2 жыл бұрын
I love the rawness of this video, real good video man.
@Nasperformance
2 жыл бұрын
Thanks man appreciate that
@TerminallySerious11 ай бұрын
I got a 2010 Mazda 6 mark-cd diesel that caught the injector Black Death, clogged the oil pickup, and cut off oil to the bearing… cleaned and fixed everything else… now your video here just gave me the courage to attempt the bearing replacements with engine in place. 🦁🔥
@Alock94
4 ай бұрын
How did you end up going?
@fasillimerick73942 жыл бұрын
For polishing the crank journal, I recommend an old fashioned, cloth measuring tape. It's roughly the same width, and it applies more even pressure.
@Nasperformance
2 жыл бұрын
Thanks for the advice
@timm5970
2 жыл бұрын
so the rod cap was polished, the crank was polished, but the rod itself was not. How would you go about that?
@markgunther2502
2 жыл бұрын
Fossil, Nah because then you can't wrap 360 degrees around.
@brihan24
Жыл бұрын
and a drill.
@everyday80sdude86
Жыл бұрын
or wide flat shoe laces.
@rickrose2235 Жыл бұрын
Replaced mine on a 2001 Jeep WJ: The bearing caps are cast into the block as part of the manufacturing process and then snapped off so that they only fit in one spot and in one orientation, it is therefore necessary to softly tap on each bearing cap with the wooden handle of a hammer to get it to seat first. Just torquing down the bearing caps without tamping them down first can lead to cracking of the bearing caps.
@everyday80sdude86
Жыл бұрын
Jeep is junk.
@Sonny1989
Жыл бұрын
Did it work?
@poolbob8776
Жыл бұрын
Tourettes, must be hereditary. Sounds like the rest of the family has it too.
@Junglist619000
8 ай бұрын
@@poolbob8776 He's like a toddler that just learned curse words
@zunrue1 Жыл бұрын
You should try 0000 steel wool for the rod. You can use it to pull rust off chrome and it won't scratch so it will keep the surface smooth.
@pauljanssen759410 ай бұрын
I used to change rod bearings out all the time as the shop owner I would listen to the engine when I change the oil if it rattled I would talk to the customer about changing some rod bearings. And maybe an oil pump.
@-------------------------theVM11 ай бұрын
0:01 second in , I see blood -- a true mechanic 😅❤
@krimsonx214x5 Жыл бұрын
The most amazing thing about this video is the fact he’s probably a millennial, yet has the knowledge to build a motor. Great job my dude
@Nasperformance
Жыл бұрын
Actually gen z
@DesertRider250r
3 ай бұрын
millennials are 40 bro. We were doing this shit in the early 2ks
@humanresources2138
2 ай бұрын
Why would the be a surprise?
@krimsonx214x5
2 ай бұрын
@@DesertRider250r you understood what I was saying, correct?
@chrismacro2012
Күн бұрын
just say young person, and you won't get called out for being wrong lmao @@krimsonx214x5
@bryco322 жыл бұрын
Had a 30k Mile AMC 304 v8 that had a carb float stick and filled the crank case full of gas and contaminated the oil . Then it sat for a decade. The shit ethanol in the gas I guess ate the bearings up. At least the first layer of plating on the factory bearings . Not all of it but enough I wanted to do something about it. Still had decent hot oil pressure at least for a amc v8. I noticed the bearings showing some copper when I went to replace the rear main seal. The crank journals mic'd out fine and looked great. Tag showed standard size bearings. I ended up running stock size bearings in both the crank and the rods.. I put them in ALL FROM UNDER THE CAR. It hasn't had a issue since. I run 15w40 Rotella and a zinc additive in it as well.
@rockyloccgarage2040
4 ай бұрын
I love rotella
@gailralls5631 Жыл бұрын
Also the bearings are top and bottom specific the bearing with a hole in it is the top block side bearing. It line's up with oil journal. Most bearings will only fit in one way. The correct way.
@shortchange269 ай бұрын
Two things I noticed. Oil behind the bearing. I don’t do it. I say if you do use the lightest oil you can find. Preferential I guess. Polishing the journal. Put the straw of a can of break clean in the oil gallery and lightly spray the sandpaper and gum junk out of there. Overall a nice video. Have fun and don’t be afraid to try something.
@lodwill5116
6 ай бұрын
Yes I just heard 👂. From pro . Don’t put oil on back of rod n bearing. I agree. . Don’t oil both sides.
@Soicydavedahtech
3 ай бұрын
Yup probably a cause for spinning them
@kevinadams55242 жыл бұрын
“don’t know his name, I just know him as the kid that sags his pants like a dumbass” had me laughing hard!
@giovannioro16423 ай бұрын
You learned from the OGs my nicka.
@joshuageorge7758 Жыл бұрын
I didn’t have any Lucas lube so I just went to the cabinet and got some KY his/hers and just used a little of each on opposite sides, just to give the bearings that cooking sensation they deserve. 😊
@YeOldeGeezer
Жыл бұрын
Pleasurable for the engine?? 🫣🫢🤣🤣
@intraterrestrial69
Жыл бұрын
@@YeOldeGeezer Always be sure to pleasure the engine, no exceptions. Every good mechanic knows this.
@AL_THOMAS_777
10 ай бұрын
@@intraterrestrial69 🙏 🤝 👍
@Ronnie-zn9sx2 жыл бұрын
i gotta tell ya, your video was very good. im working on a ford escape, and am replacing my rod bearings. been watching alot of videos on this subject and yours is best at lighting, sound and i love the language. thx
@Nasperformance
2 жыл бұрын
Thank you 🙏 we try to record everything we do and try to get the best angle so that it’s easy to understand
@ceomaliyeckal1307
2 жыл бұрын
Im also watching all these videos trying to change my 2009 ford escape rod bearings. Did u changed it?
@Nasperformance
2 жыл бұрын
@@ceomaliyeckal1307 yes I change mine but it was on a 2004 Chevy Colorado
@Ronnie-zn9sx
2 жыл бұрын
@@ceomaliyeckal1307 working on a 06 escape. Just ordered gauges so i can measure bearing clearance. Not enough information online nor on the escape forums. I may get the Haynes manual also. If you get any good information please pass it on.
@ceomaliyeckal1307
2 жыл бұрын
@@Ronnie-zn9sx kzread.info/dash/bejne/anmtzZmcgsq_iJM.html this video may help
@markgunther25022 жыл бұрын
I had elongated one of the rods just like yours. There are two ways to handle it. 1) add a shim to the lower bearing or get an oversize bearing for the lower half until your plastigauge shows its in spec. 2) Grind down the rod cap to con rod mating edges until your plastigauge shows its back in spec. I did 1) and it's held up fine for 6 months now in a turbocharged engine. 2) Is probably the more correct way. Both procedures can be done with the engine in the car still.
@terrellscaife2411
2 жыл бұрын
I got a question for you what’s the best way to figure out what size rod bearings you need
@markgunther2502
2 жыл бұрын
@@terrellscaife2411 If you haven't ground your crank at a machine shop, then start with standard sized bearings. Then plastigauge to check its within specs.
@terrellscaife2411
2 жыл бұрын
🙏
@V8Lounge
Жыл бұрын
Do You drive it normal and race it or do You drive only low revs?
@markgunther2502
Жыл бұрын
@@V8Lounge Low rev the first 500 miles or so, now normal, up to red line with full boost.
@miketriesmotorsports6080 Жыл бұрын
This is really clever. Great job!
@murkypuddle33 Жыл бұрын
very cool. i got this ranger with a rod knock i can buy for like $300. it looks like i just need to replace the bearings (i hope) the way you showed me how to do it doesn't look that hard, i like how i dont gotta put it on a lift or take the engine off
@raulciprianoyahoo
5 ай бұрын
This will only extend the life of the engine a couple of months
@rockyloccgarage2040
4 ай бұрын
U can buy anew crankshaft for it too.
@unexpectedmixoflife4851
6 күн бұрын
@@raulciprianoyahoohow so?
@nelsonmarquina94273 жыл бұрын
Thanks no one else has any videos on this topic
@Abualameer6911 ай бұрын
I love the vide but I wish you showed how to get the bearings BUT I REALLY LOVE THE VIDEO thanks man
@_desertwalker_3 ай бұрын
greetings from Western Australia. Great vid.
@michaelkline21362 жыл бұрын
Iv done this works great. Just keep everything clean and grab yourself a set of Standard and 20 over bearings
@Nasperformance
2 жыл бұрын
That is exactly what we did👍🏽
@Z-Ack
4 ай бұрын
U mean 20 under right? Like .0020” undersized..
@Z-Ack
4 ай бұрын
Or .020”. Not .00…
@mikegregory253522 күн бұрын
Living and learning, my hats off to you.
@cam03663 жыл бұрын
thanks this really helped a lot with changing my oil
@HBJStudios Жыл бұрын
Would you take a cross country trip after doing this?
@hajrudinkavazovic2231 Жыл бұрын
Good job buddy nice end important video to show Mechanic's how to do with out engine out they don't like your video I no what they think thanks and i appreciate your show and Job to show por people to do by self with out mechanic Steeler shop.becose they like to make money easy with out you do 🤟🔥
@MustangBullitt-sz8tg2 жыл бұрын
Looks like I have a project to do now after my Pontiac just had spun a bearing. Thanks for the DIY video I'll update and let ya know how mine turns out...
@Slowwvqs
2 жыл бұрын
How did it turn out? My car is making the same noise
@Protege27
2 жыл бұрын
How’d it go man
@phillippardo5712
Жыл бұрын
Update?
@MXCHINO18
11 ай бұрын
Engine blew
@marvacevedo3857
Ай бұрын
Update?
@davidgomez3737 Жыл бұрын
Hey bro did you have to measure bearing clearance or did you just slap the new bearings on and torque them down to spec
@nelsoncanelas19782 жыл бұрын
mines had the same noise I had to replace the timing oil tensioner because it was leaking oil really bad and my bro always ran it on low oil. Now the engine will crank and start but won’t stay on I had to replace the battery because it was bad. Maybe the bad battery fried my alternator? Or maybe I missed aligned the timing when replacing the oil timing tensioner? Ahh am stuck trying to figure out if I need a new engine or not?
@JAnBG57479 ай бұрын
🤣🤣 I was laughing the whole time! Thanks for the vid
@otonielaburtobermejo47742 жыл бұрын
What year and model? Also did you take off the oil pump/ladder frane ?
@TFYS-QA2 жыл бұрын
Impressive! If I was doing that, I'd be saying a lot more curse words.... I tend to be a Murph magnet when doing stuff like that
@saintmarckaeden
2 жыл бұрын
I thought I would be doing the same but in the process of doing it now and it’s actually one of the easiest jobs! I bought new ones cause mine were shot but very helpful video!
@juliuscaesar756 Жыл бұрын
You can tell my mans uses that hand quite often 😁
@cabreallsiams92775 ай бұрын
Thanks for video, my car has oil pump in the way so can't access the rod, did you have same issue but already removed the oil pump? I'm not sure how to remove the oil pump
@Denzar007Ай бұрын
Good work. Which connecting rods did u change. Which cylinders 1,3,4
@christopherdherman15182 жыл бұрын
After the third time you said, fuck I just had to subscribe. Lol. Awesomeness at its best 👌.
@Nasperformance
2 жыл бұрын
Thanks man😂I try my best to not cus but while you work on a car it just comes out 😂
@pnuema1.6182 жыл бұрын
Never lube the back side of main or rod bearings. Lube only the front side, assembly lube is preferred because its more like a grease and can handle start up for the first time better.
@porigense67
Жыл бұрын
so lube the side that touches the crank?
@tnfloose9023
Жыл бұрын
@@porigense67 yes. Oil isn't supposed to go on the backside where there is nothing moving. It can put you at higher risk of spinning a bearing.
@psiturbo
Жыл бұрын
@@tnfloose9023 Papadakis and many more engine builders apply oil to the rod caps... kzread.info/dash/bejne/q3Woj8ikhNHamqg.html
@psiturbo
Жыл бұрын
Here is another video, "Inside the Box" AMG factory, engine building, at the two minute fifty five, the Mercedes engine builder puts copious amounts of oil between rod and back of the bearing... kzread.info/dash/bejne/emxm1cWwqtzOmJM.html
@rickrose2235
Жыл бұрын
Why sand the back surface of the bearing cap just so it will be shinny, seems that it will be more likely to spin a bearing?
@josephpark18254 Жыл бұрын
What was the result? Engine still running? Trying to decide whether i do mine or not
@illwill915 Жыл бұрын
Sounds like me when I fuck up something simple while working on a car🤣
@papergatorzfedducca7998 Жыл бұрын
how long do you use the shoe strings on the journal. I’m doing this and don’t want to sand it too long.😂😂😂
@bluegill20302 жыл бұрын
Does this process also work for doing I’m on the very end of the crank the caps
@danpeterson37392 жыл бұрын
Hey great video by da way so I wanted to know what motor was that you were working on I infact have a wat seems to be rod knock im my 03 jeep 4.7l limited I'm going to be doing this for my motor and your vid is great 👍 for step my step ill also be doing the cams timing chain and the lifters and rocker arms on it I had a oil leak when I first bought and I finally got it fixed but I guess da damage was already done Is the car u fixed still running no issues
@robertbrown6755
2 жыл бұрын
This comment probably is not going to help now but anytime you have a rod knocking in your car and it's bad enough that you're hearing it you should always have that Rod recondition
@HarryHockersmith10 күн бұрын
How did you remove the upper oil pan?
@HoytFergus3 ай бұрын
Remove the Plugs and the Crank turns super easy/ Nice video, I once was in the Alaskan wilderness lost a bearing and cut up my leather pants belt and used leather as the bearing. Literally lasted a year.... js
@OldCaliboy2 жыл бұрын
So how did everything turn out after you put the engagement back together? I've done this year ago after changing the crank but did change the connecting rods... they became baffled and out of round. That led to the engine falling shortly afterwards. It was on a 350 block.
@Nasperformance
2 жыл бұрын
We actually had to order a pair of 20 thousandths oversized bearings for the first connecting rod and the rest were standard sized bearings we slapped everything back together and she started up first crank
@OldCaliboy
2 жыл бұрын
@@Nasperformance Really! Well that's nice. Ordered a set of oversized Baring was a smart move. That's awesome. Thanks for sharing with us your experience 👍.
@psiturbo
Жыл бұрын
@@Nasperformance the question was more, long term, did it run well many months later? any other rod knock issues?
@MatthewBecker7
Жыл бұрын
@@Nasperformance after putting the 20 thousandth oversized was there still a little bit of play?
@f.stopperrmedia1606
Жыл бұрын
@@MatthewBecker7 there would still have been a tiny amount. Not nearly as much as in the video. Just enough to fit a sheet of paper or two in between. Thats all the play you need.
@noahmarr76712 жыл бұрын
When turning your harmonic balancer like this do you not have to set the timing back? Does it not mess with timing
@Nasperformance
2 жыл бұрын
No not at all the timing is hooked up to the crank sprocket
@sunzoo4673
2 жыл бұрын
Only if you remove the belt
@styleauto10252 ай бұрын
Nice video thank you
@hollowpoint31884 ай бұрын
So i have a 93 5.0 i took the rod bearings and mixed up the the tops marked some but by the time i realized it was too late is there anyway to fix this
@lilcarlos13152 жыл бұрын
Hey bro i was wondering if i change my 2007 civic 1.8l rod bearingz do i oversize ? Or how do i know which one to buy
@Nasperformance
2 жыл бұрын
You have to measure the diameter of your crank shaft rod journal with a micrometer and search up your factory measurement and do the math from there
@josephtesnear2426 Жыл бұрын
thank you for this video 😂😂👌👌
@Mercury_man2 жыл бұрын
how bad was the engine knock when you reassembled then? did piston #1 last more than 6 months?
@maurizioalfieri602
2 жыл бұрын
Why?
@ozgurugur7609 Жыл бұрын
Hello I have a question. The area you are working on it is where the oil pan goes right? I I basically need t take the oil pan out the reach the area you are working on then I am gonna be able to replace rod bearings?
@Nasperformance
Жыл бұрын
Yes
@destruxandexploze2552 Жыл бұрын
My eyes went wide when he lubed behind the bearing
@robertbrown67552 жыл бұрын
You should never use anything between the rod cap and the rod bearing.
@Maleekus
2 жыл бұрын
I assume you mean lube, in which case I agree. You don't want the bearing to move in the cap
@robertbrown6755
2 жыл бұрын
Tha 2 that thumbs-down me if you believe you should one day you will learn your lesson cuz it will happen
@gregorymalchuk272
4 ай бұрын
@@robertbrown6755I know a guy that used loctite between the rod cap and the rod bearing. It's an old trick from stock car racing.
@williamconroy1762 жыл бұрын
Definitely gonna give this a crack, my Ranger has a slight knock
@codyunderwood774111 ай бұрын
Bro My FA20 Small block started knocking on me this past weekend. I hope it isn’t anything more serious than I quick bearing replacement. Honestly I’m nervous as fuck to open her up like that but watching you do this made it look dumb easy. How did it run after you replaced the bearings?
@txboy112233 Жыл бұрын
I have a 6.0 and the clatter my best guess is the rid knock. Please comment if it ran like a champ.
@joewontwice2 күн бұрын
Did you pull the trans?
@stevendyer13492 жыл бұрын
Great video the shoelace is og
@Nasperformance
2 жыл бұрын
Thank you
@eddyoviedo306225 күн бұрын
Did you remove the spark plugs first
@jedm32688 ай бұрын
Since when do you lube the backside of the bearing? If you want a spun bearing then go for it.
@jeremysanders8138
3 ай бұрын
He should've used just regular motor oil. There's supposed to be .0001 to .0002 tolerance for oil to get in there. Heavy lube will prevent that
@wolfparty42342 жыл бұрын
Ok, FUUUUUCK!!!!!🤣🤣🤣 Nice work fellas!!!
@markmkv94011 ай бұрын
Curious how long this latest before spinning a bearing or knocking again
@drsanmyattun
6 ай бұрын
10k miles Max.
@gregorymalchuk272
4 ай бұрын
You have to use super glue on the back side of the new bearing, especially if the bearing shell has been spinning a lot inside the rod cap. It's actually a trick from stock car racing. The engines go back together for a lot more high revs.
@sadamohammad20972 жыл бұрын
Thanks very much to see this
@pauloremez29545 ай бұрын
God Bless you in The Name of JESUS for making and Posting This Video
@swordfish11202 жыл бұрын
Did you have a rod knock? What kind of vehicle?
@robertocruz11772 жыл бұрын
What I’m wondering is why does your cap portion of the bearing have an oil hole? Shouldn’t that be on the top end in the saddle (block)?!
@markdesselle5572
2 жыл бұрын
My f series honda both sides of bearing have the oil passage. I guess so they can go top or bottom.
@Goodtime-vf2cs Жыл бұрын
Can you change the thrust washer while the motor is in the car
@MP7A1pdw2 жыл бұрын
Bro the best commentary ever. "FUCK"
@Nasperformance
2 жыл бұрын
Thanks😂
@bencrosbie2 жыл бұрын
Love this video hahaha
@pedromanriquez9695 Жыл бұрын
Have to empty the engine oil or transmission oil thank you. Please help
@Khaotic_dreams2 ай бұрын
Great free fireworks you just increased 800hp straight throught engine to planet mars
@jaredreck882 Жыл бұрын
Thanks brother
@dj_pandemic_2 ай бұрын
the 'f***s" be killing me. 🤣🤣🤣
@waltercardenas7354 Жыл бұрын
I have a Chevy 1996 5.7L 350 Sb is knocking noise. I took the oil pan out and found metal residual. I was told I need a new engine. The engine turn on and drives. Any advice please. Thanks
@1kbutta
Жыл бұрын
Did you figure out what it was?
@waltercardenas7354
Жыл бұрын
Just replace the engine. Got a good deal on ebay. New block. Thanks
@muhammedlandry8453 жыл бұрын
Thanks for the help 👍
@Nasperformance
3 жыл бұрын
Your welcome
@brandonrichards48802 жыл бұрын
You always always always want to replace any type of main internal bolts that are torqued.
@damaxpowerway
Жыл бұрын
What of they don't fit the same as the originals?
@user-nx7jh2fb5iАй бұрын
This video is great lol😂
@neltontimas69594 ай бұрын
Were u get the part
@jordanamorasin18402 жыл бұрын
What do you suggest we should do when It comes to torquing down the rods. Should we reuse, swap to new OEM rods or get arp? I've read that we will need to resize rods with arp. Are we simply working with what we have and then just send it?
@Nasperformance
2 жыл бұрын
To be honest you don’t really need arp bolts if you aren’t building it but that doesn’t mean you can’t its just preference
@rickrose2235
Жыл бұрын
Dispite what a lot of people say here, you can reuse rod bolts as long as the bolts haven't been torqued over the TTY i.e. "Torque to yield value" and have not been permanently deformed. Suggestion when torquing the rod bolts creep up on the maximum torque numbers in stages slowly being sure to torque each bolt evenly as you go up in torque to the max torque. Best to apply assembly lube to the journals and bearing surfaces that face each other, it is thicker then oil and gives more protection since the oil pump won't supply oil to the bearings until the pump primes itself and starts pumping oil again.
@intraterrestrial69 Жыл бұрын
Haha I mean I wouldn’t do this to any car but shit they do stuff like this all the time in Bangladesh and it works for an unknown amount of time. Do it still run?
@jjhills24632 жыл бұрын
Chrysler 300? Could you tell me the specs for the bearings?
@Nasperformance
2 жыл бұрын
What year and engine size?
@HandMadeWrath Жыл бұрын
When he libed the cap i was like wtf
@vids5952 жыл бұрын
You didn't show how you determined what size bearing to use for replacement.
@Arrowpainplays
Жыл бұрын
OE and ride it till it dies this isnt a permanent fix. Just making it last another year or so
@jakejakenson8145Ай бұрын
Can u do 1 wit the motor running?
@bayleykelley69582 жыл бұрын
How well did this job hold up? About to do this myself. Thanks in advance for the reply
@Nasperformance
2 жыл бұрын
Held up extremely good actually but my motor started to have oiling problems and blew up 😂 so I ls swapped it
@kashtaandrade4017
2 жыл бұрын
@@Nasperformance 🤣🤣 was it from the bearings
@Nasperformance
2 жыл бұрын
@@kashtaandrade4017 no the oil pump went out and starved the motor😂
@jerryhamptonjr731852 жыл бұрын
How many miles did it run before it spun again?
@1kbutta
Жыл бұрын
That’s what I wanna know
@eddietaylor7323 Жыл бұрын
How do you know if you need an over size bearing?
@Nasperformance
Жыл бұрын
Use a micrometer and measure the outside diameter of the crank also google your engines factory diameter and compare the two measurements
@eddietaylor7323
Жыл бұрын
@@Nasperformance thank you so much for your help
@lrm17romo93 Жыл бұрын
What grid ?
@robertmahaney42712 жыл бұрын
Mom and Dad must be at work , everyone in the video used the F-bombs like they just learned there first cuss word😳😂
@Nasperformance
2 жыл бұрын
Lol you must be mad that I’m younger than you and doing things like this
@gilpena95912 жыл бұрын
Did this job workout for u? just wondering , I'm about to attempt thrust washers on my pt cruiser . maybe the whole set. is it still running? any knocking ?
@Nasperformance
2 жыл бұрын
Ran great just ended up ls swaping it
@dcptveemcee35402 жыл бұрын
How do I get the oil girdle off.i took the ten bolts out
@Nasperformance
2 жыл бұрын
For me I just came right off after the main cap bolts were out
@dannypalmer77012 жыл бұрын
I cuss too! Lol 😂
@carpentarhartley8624 Жыл бұрын
If the bearing spun, crank is gonna be "flat" spotted on load side. Knock will be quieter but will end the same eventually
@jaredreck882
Жыл бұрын
It will keep it from shooting out the oil pan right ? Lol I saw this video when my van was knocking I wish I would’ve listened
@oscarlopez20162 жыл бұрын
So the first rod is supposed to be kinda loose to we’re it shakes?
@nelsonmarquina9427
2 жыл бұрын
Nah it was just fucked up
@oscarlopez2016
2 жыл бұрын
@@nelsonmarquina9427 oh okay so you just put on a thicker bearing?
@Realofficialdee
Жыл бұрын
What he said ?^
@davidmendoza9659 Жыл бұрын
Can I get part number for this please
@dlanniltd2 жыл бұрын
Somebody tell the females you were trying to record a video?
Пікірлер: 325
Helped me out bro I wasn’t gonna mess with my Buick cause it has rod knock but today I learned that it only takes about six or seven f***s and a little work and I can get this done 😂..preciate ya bro
@Nasperformance
2 жыл бұрын
What Buick you got and what size motor is it
@solojoe1193
2 жыл бұрын
@@Nasperformance 2003 park avenue 3.8L
@earthbros6508
Жыл бұрын
Don’t forget the liquid courage 🍻
Nice to see that having tourettes has not stopped him from doing the job he loves. Great work.
@abdulalhazred4589
2 жыл бұрын
Yeah, tourettes, the champion's illness.... 😆😸😆😸
@c4r5on88
2 жыл бұрын
@@abdulalhazred4589 that explains why I'm currently not a champion then. I need to swear more 😂
@Usaamah_Haarithi
Жыл бұрын
Lol
@joeo1725
Жыл бұрын
I won't use this video while my childs around.
@Junglist619000
8 ай бұрын
He sounds like a 5 year old that just learned curse words
I wouldn't call this jank at all dude this is a work of art.
I love the rawness of this video, real good video man.
@Nasperformance
2 жыл бұрын
Thanks man appreciate that
I got a 2010 Mazda 6 mark-cd diesel that caught the injector Black Death, clogged the oil pickup, and cut off oil to the bearing… cleaned and fixed everything else… now your video here just gave me the courage to attempt the bearing replacements with engine in place. 🦁🔥
@Alock94
4 ай бұрын
How did you end up going?
For polishing the crank journal, I recommend an old fashioned, cloth measuring tape. It's roughly the same width, and it applies more even pressure.
@Nasperformance
2 жыл бұрын
Thanks for the advice
@timm5970
2 жыл бұрын
so the rod cap was polished, the crank was polished, but the rod itself was not. How would you go about that?
@markgunther2502
2 жыл бұрын
Fossil, Nah because then you can't wrap 360 degrees around.
@brihan24
Жыл бұрын
and a drill.
@everyday80sdude86
Жыл бұрын
or wide flat shoe laces.
Replaced mine on a 2001 Jeep WJ: The bearing caps are cast into the block as part of the manufacturing process and then snapped off so that they only fit in one spot and in one orientation, it is therefore necessary to softly tap on each bearing cap with the wooden handle of a hammer to get it to seat first. Just torquing down the bearing caps without tamping them down first can lead to cracking of the bearing caps.
@everyday80sdude86
Жыл бұрын
Jeep is junk.
@Sonny1989
Жыл бұрын
Did it work?
@poolbob8776
Жыл бұрын
Tourettes, must be hereditary. Sounds like the rest of the family has it too.
@Junglist619000
8 ай бұрын
@@poolbob8776 He's like a toddler that just learned curse words
You should try 0000 steel wool for the rod. You can use it to pull rust off chrome and it won't scratch so it will keep the surface smooth.
I used to change rod bearings out all the time as the shop owner I would listen to the engine when I change the oil if it rattled I would talk to the customer about changing some rod bearings. And maybe an oil pump.
0:01 second in , I see blood -- a true mechanic 😅❤
The most amazing thing about this video is the fact he’s probably a millennial, yet has the knowledge to build a motor. Great job my dude
@Nasperformance
Жыл бұрын
Actually gen z
@DesertRider250r
3 ай бұрын
millennials are 40 bro. We were doing this shit in the early 2ks
@humanresources2138
2 ай бұрын
Why would the be a surprise?
@krimsonx214x5
2 ай бұрын
@@DesertRider250r you understood what I was saying, correct?
@chrismacro2012
Күн бұрын
just say young person, and you won't get called out for being wrong lmao @@krimsonx214x5
Had a 30k Mile AMC 304 v8 that had a carb float stick and filled the crank case full of gas and contaminated the oil . Then it sat for a decade. The shit ethanol in the gas I guess ate the bearings up. At least the first layer of plating on the factory bearings . Not all of it but enough I wanted to do something about it. Still had decent hot oil pressure at least for a amc v8. I noticed the bearings showing some copper when I went to replace the rear main seal. The crank journals mic'd out fine and looked great. Tag showed standard size bearings. I ended up running stock size bearings in both the crank and the rods.. I put them in ALL FROM UNDER THE CAR. It hasn't had a issue since. I run 15w40 Rotella and a zinc additive in it as well.
@rockyloccgarage2040
4 ай бұрын
I love rotella
Also the bearings are top and bottom specific the bearing with a hole in it is the top block side bearing. It line's up with oil journal. Most bearings will only fit in one way. The correct way.
Two things I noticed. Oil behind the bearing. I don’t do it. I say if you do use the lightest oil you can find. Preferential I guess. Polishing the journal. Put the straw of a can of break clean in the oil gallery and lightly spray the sandpaper and gum junk out of there. Overall a nice video. Have fun and don’t be afraid to try something.
@lodwill5116
6 ай бұрын
Yes I just heard 👂. From pro . Don’t put oil on back of rod n bearing. I agree. . Don’t oil both sides.
@Soicydavedahtech
3 ай бұрын
Yup probably a cause for spinning them
“don’t know his name, I just know him as the kid that sags his pants like a dumbass” had me laughing hard!
You learned from the OGs my nicka.
I didn’t have any Lucas lube so I just went to the cabinet and got some KY his/hers and just used a little of each on opposite sides, just to give the bearings that cooking sensation they deserve. 😊
@YeOldeGeezer
Жыл бұрын
Pleasurable for the engine?? 🫣🫢🤣🤣
@intraterrestrial69
Жыл бұрын
@@YeOldeGeezer Always be sure to pleasure the engine, no exceptions. Every good mechanic knows this.
@AL_THOMAS_777
10 ай бұрын
@@intraterrestrial69 🙏 🤝 👍
i gotta tell ya, your video was very good. im working on a ford escape, and am replacing my rod bearings. been watching alot of videos on this subject and yours is best at lighting, sound and i love the language. thx
@Nasperformance
2 жыл бұрын
Thank you 🙏 we try to record everything we do and try to get the best angle so that it’s easy to understand
@ceomaliyeckal1307
2 жыл бұрын
Im also watching all these videos trying to change my 2009 ford escape rod bearings. Did u changed it?
@Nasperformance
2 жыл бұрын
@@ceomaliyeckal1307 yes I change mine but it was on a 2004 Chevy Colorado
@Ronnie-zn9sx
2 жыл бұрын
@@ceomaliyeckal1307 working on a 06 escape. Just ordered gauges so i can measure bearing clearance. Not enough information online nor on the escape forums. I may get the Haynes manual also. If you get any good information please pass it on.
@ceomaliyeckal1307
2 жыл бұрын
@@Ronnie-zn9sx kzread.info/dash/bejne/anmtzZmcgsq_iJM.html this video may help
I had elongated one of the rods just like yours. There are two ways to handle it. 1) add a shim to the lower bearing or get an oversize bearing for the lower half until your plastigauge shows its in spec. 2) Grind down the rod cap to con rod mating edges until your plastigauge shows its back in spec. I did 1) and it's held up fine for 6 months now in a turbocharged engine. 2) Is probably the more correct way. Both procedures can be done with the engine in the car still.
@terrellscaife2411
2 жыл бұрын
I got a question for you what’s the best way to figure out what size rod bearings you need
@markgunther2502
2 жыл бұрын
@@terrellscaife2411 If you haven't ground your crank at a machine shop, then start with standard sized bearings. Then plastigauge to check its within specs.
@terrellscaife2411
2 жыл бұрын
🙏
@V8Lounge
Жыл бұрын
Do You drive it normal and race it or do You drive only low revs?
@markgunther2502
Жыл бұрын
@@V8Lounge Low rev the first 500 miles or so, now normal, up to red line with full boost.
This is really clever. Great job!
very cool. i got this ranger with a rod knock i can buy for like $300. it looks like i just need to replace the bearings (i hope) the way you showed me how to do it doesn't look that hard, i like how i dont gotta put it on a lift or take the engine off
@raulciprianoyahoo
5 ай бұрын
This will only extend the life of the engine a couple of months
@rockyloccgarage2040
4 ай бұрын
U can buy anew crankshaft for it too.
@unexpectedmixoflife4851
6 күн бұрын
@@raulciprianoyahoohow so?
Thanks no one else has any videos on this topic
I love the vide but I wish you showed how to get the bearings BUT I REALLY LOVE THE VIDEO thanks man
greetings from Western Australia. Great vid.
Iv done this works great. Just keep everything clean and grab yourself a set of Standard and 20 over bearings
@Nasperformance
2 жыл бұрын
That is exactly what we did👍🏽
@Z-Ack
4 ай бұрын
U mean 20 under right? Like .0020” undersized..
@Z-Ack
4 ай бұрын
Or .020”. Not .00…
Living and learning, my hats off to you.
thanks this really helped a lot with changing my oil
Would you take a cross country trip after doing this?
Good job buddy nice end important video to show Mechanic's how to do with out engine out they don't like your video I no what they think thanks and i appreciate your show and Job to show por people to do by self with out mechanic Steeler shop.becose they like to make money easy with out you do 🤟🔥
Looks like I have a project to do now after my Pontiac just had spun a bearing. Thanks for the DIY video I'll update and let ya know how mine turns out...
@Slowwvqs
2 жыл бұрын
How did it turn out? My car is making the same noise
@Protege27
2 жыл бұрын
How’d it go man
@phillippardo5712
Жыл бұрын
Update?
@MXCHINO18
11 ай бұрын
Engine blew
@marvacevedo3857
Ай бұрын
Update?
Hey bro did you have to measure bearing clearance or did you just slap the new bearings on and torque them down to spec
mines had the same noise I had to replace the timing oil tensioner because it was leaking oil really bad and my bro always ran it on low oil. Now the engine will crank and start but won’t stay on I had to replace the battery because it was bad. Maybe the bad battery fried my alternator? Or maybe I missed aligned the timing when replacing the oil timing tensioner? Ahh am stuck trying to figure out if I need a new engine or not?
🤣🤣 I was laughing the whole time! Thanks for the vid
What year and model? Also did you take off the oil pump/ladder frane ?
Impressive! If I was doing that, I'd be saying a lot more curse words.... I tend to be a Murph magnet when doing stuff like that
@saintmarckaeden
2 жыл бұрын
I thought I would be doing the same but in the process of doing it now and it’s actually one of the easiest jobs! I bought new ones cause mine were shot but very helpful video!
You can tell my mans uses that hand quite often 😁
Thanks for video, my car has oil pump in the way so can't access the rod, did you have same issue but already removed the oil pump? I'm not sure how to remove the oil pump
Good work. Which connecting rods did u change. Which cylinders 1,3,4
After the third time you said, fuck I just had to subscribe. Lol. Awesomeness at its best 👌.
@Nasperformance
2 жыл бұрын
Thanks man😂I try my best to not cus but while you work on a car it just comes out 😂
Never lube the back side of main or rod bearings. Lube only the front side, assembly lube is preferred because its more like a grease and can handle start up for the first time better.
@porigense67
Жыл бұрын
so lube the side that touches the crank?
@tnfloose9023
Жыл бұрын
@@porigense67 yes. Oil isn't supposed to go on the backside where there is nothing moving. It can put you at higher risk of spinning a bearing.
@psiturbo
Жыл бұрын
@@tnfloose9023 Papadakis and many more engine builders apply oil to the rod caps... kzread.info/dash/bejne/q3Woj8ikhNHamqg.html
@psiturbo
Жыл бұрын
Here is another video, "Inside the Box" AMG factory, engine building, at the two minute fifty five, the Mercedes engine builder puts copious amounts of oil between rod and back of the bearing... kzread.info/dash/bejne/emxm1cWwqtzOmJM.html
@rickrose2235
Жыл бұрын
Why sand the back surface of the bearing cap just so it will be shinny, seems that it will be more likely to spin a bearing?
What was the result? Engine still running? Trying to decide whether i do mine or not
Sounds like me when I fuck up something simple while working on a car🤣
how long do you use the shoe strings on the journal. I’m doing this and don’t want to sand it too long.😂😂😂
Does this process also work for doing I’m on the very end of the crank the caps
Hey great video by da way so I wanted to know what motor was that you were working on I infact have a wat seems to be rod knock im my 03 jeep 4.7l limited I'm going to be doing this for my motor and your vid is great 👍 for step my step ill also be doing the cams timing chain and the lifters and rocker arms on it I had a oil leak when I first bought and I finally got it fixed but I guess da damage was already done Is the car u fixed still running no issues
@robertbrown6755
2 жыл бұрын
This comment probably is not going to help now but anytime you have a rod knocking in your car and it's bad enough that you're hearing it you should always have that Rod recondition
How did you remove the upper oil pan?
Remove the Plugs and the Crank turns super easy/ Nice video, I once was in the Alaskan wilderness lost a bearing and cut up my leather pants belt and used leather as the bearing. Literally lasted a year.... js
So how did everything turn out after you put the engagement back together? I've done this year ago after changing the crank but did change the connecting rods... they became baffled and out of round. That led to the engine falling shortly afterwards. It was on a 350 block.
@Nasperformance
2 жыл бұрын
We actually had to order a pair of 20 thousandths oversized bearings for the first connecting rod and the rest were standard sized bearings we slapped everything back together and she started up first crank
@OldCaliboy
2 жыл бұрын
@@Nasperformance Really! Well that's nice. Ordered a set of oversized Baring was a smart move. That's awesome. Thanks for sharing with us your experience 👍.
@psiturbo
Жыл бұрын
@@Nasperformance the question was more, long term, did it run well many months later? any other rod knock issues?
@MatthewBecker7
Жыл бұрын
@@Nasperformance after putting the 20 thousandth oversized was there still a little bit of play?
@f.stopperrmedia1606
Жыл бұрын
@@MatthewBecker7 there would still have been a tiny amount. Not nearly as much as in the video. Just enough to fit a sheet of paper or two in between. Thats all the play you need.
When turning your harmonic balancer like this do you not have to set the timing back? Does it not mess with timing
@Nasperformance
2 жыл бұрын
No not at all the timing is hooked up to the crank sprocket
@sunzoo4673
2 жыл бұрын
Only if you remove the belt
Nice video thank you
So i have a 93 5.0 i took the rod bearings and mixed up the the tops marked some but by the time i realized it was too late is there anyway to fix this
Hey bro i was wondering if i change my 2007 civic 1.8l rod bearingz do i oversize ? Or how do i know which one to buy
@Nasperformance
2 жыл бұрын
You have to measure the diameter of your crank shaft rod journal with a micrometer and search up your factory measurement and do the math from there
thank you for this video 😂😂👌👌
how bad was the engine knock when you reassembled then? did piston #1 last more than 6 months?
@maurizioalfieri602
2 жыл бұрын
Why?
Hello I have a question. The area you are working on it is where the oil pan goes right? I I basically need t take the oil pan out the reach the area you are working on then I am gonna be able to replace rod bearings?
@Nasperformance
Жыл бұрын
Yes
My eyes went wide when he lubed behind the bearing
You should never use anything between the rod cap and the rod bearing.
@Maleekus
2 жыл бұрын
I assume you mean lube, in which case I agree. You don't want the bearing to move in the cap
@robertbrown6755
2 жыл бұрын
Tha 2 that thumbs-down me if you believe you should one day you will learn your lesson cuz it will happen
@gregorymalchuk272
4 ай бұрын
@@robertbrown6755I know a guy that used loctite between the rod cap and the rod bearing. It's an old trick from stock car racing.
Definitely gonna give this a crack, my Ranger has a slight knock
Bro My FA20 Small block started knocking on me this past weekend. I hope it isn’t anything more serious than I quick bearing replacement. Honestly I’m nervous as fuck to open her up like that but watching you do this made it look dumb easy. How did it run after you replaced the bearings?
I have a 6.0 and the clatter my best guess is the rid knock. Please comment if it ran like a champ.
Did you pull the trans?
Great video the shoelace is og
@Nasperformance
2 жыл бұрын
Thank you
Did you remove the spark plugs first
Since when do you lube the backside of the bearing? If you want a spun bearing then go for it.
@jeremysanders8138
3 ай бұрын
He should've used just regular motor oil. There's supposed to be .0001 to .0002 tolerance for oil to get in there. Heavy lube will prevent that
Ok, FUUUUUCK!!!!!🤣🤣🤣 Nice work fellas!!!
Curious how long this latest before spinning a bearing or knocking again
@drsanmyattun
6 ай бұрын
10k miles Max.
@gregorymalchuk272
4 ай бұрын
You have to use super glue on the back side of the new bearing, especially if the bearing shell has been spinning a lot inside the rod cap. It's actually a trick from stock car racing. The engines go back together for a lot more high revs.
Thanks very much to see this
God Bless you in The Name of JESUS for making and Posting This Video
Did you have a rod knock? What kind of vehicle?
What I’m wondering is why does your cap portion of the bearing have an oil hole? Shouldn’t that be on the top end in the saddle (block)?!
@markdesselle5572
2 жыл бұрын
My f series honda both sides of bearing have the oil passage. I guess so they can go top or bottom.
Can you change the thrust washer while the motor is in the car
Bro the best commentary ever. "FUCK"
@Nasperformance
2 жыл бұрын
Thanks😂
Love this video hahaha
Have to empty the engine oil or transmission oil thank you. Please help
Great free fireworks you just increased 800hp straight throught engine to planet mars
Thanks brother
the 'f***s" be killing me. 🤣🤣🤣
I have a Chevy 1996 5.7L 350 Sb is knocking noise. I took the oil pan out and found metal residual. I was told I need a new engine. The engine turn on and drives. Any advice please. Thanks
@1kbutta
Жыл бұрын
Did you figure out what it was?
@waltercardenas7354
Жыл бұрын
Just replace the engine. Got a good deal on ebay. New block. Thanks
Thanks for the help 👍
@Nasperformance
3 жыл бұрын
Your welcome
You always always always want to replace any type of main internal bolts that are torqued.
@damaxpowerway
Жыл бұрын
What of they don't fit the same as the originals?
This video is great lol😂
Were u get the part
What do you suggest we should do when It comes to torquing down the rods. Should we reuse, swap to new OEM rods or get arp? I've read that we will need to resize rods with arp. Are we simply working with what we have and then just send it?
@Nasperformance
2 жыл бұрын
To be honest you don’t really need arp bolts if you aren’t building it but that doesn’t mean you can’t its just preference
@rickrose2235
Жыл бұрын
Dispite what a lot of people say here, you can reuse rod bolts as long as the bolts haven't been torqued over the TTY i.e. "Torque to yield value" and have not been permanently deformed. Suggestion when torquing the rod bolts creep up on the maximum torque numbers in stages slowly being sure to torque each bolt evenly as you go up in torque to the max torque. Best to apply assembly lube to the journals and bearing surfaces that face each other, it is thicker then oil and gives more protection since the oil pump won't supply oil to the bearings until the pump primes itself and starts pumping oil again.
Haha I mean I wouldn’t do this to any car but shit they do stuff like this all the time in Bangladesh and it works for an unknown amount of time. Do it still run?
Chrysler 300? Could you tell me the specs for the bearings?
@Nasperformance
2 жыл бұрын
What year and engine size?
When he libed the cap i was like wtf
You didn't show how you determined what size bearing to use for replacement.
@Arrowpainplays
Жыл бұрын
OE and ride it till it dies this isnt a permanent fix. Just making it last another year or so
Can u do 1 wit the motor running?
How well did this job hold up? About to do this myself. Thanks in advance for the reply
@Nasperformance
2 жыл бұрын
Held up extremely good actually but my motor started to have oiling problems and blew up 😂 so I ls swapped it
@kashtaandrade4017
2 жыл бұрын
@@Nasperformance 🤣🤣 was it from the bearings
@Nasperformance
2 жыл бұрын
@@kashtaandrade4017 no the oil pump went out and starved the motor😂
How many miles did it run before it spun again?
@1kbutta
Жыл бұрын
That’s what I wanna know
How do you know if you need an over size bearing?
@Nasperformance
Жыл бұрын
Use a micrometer and measure the outside diameter of the crank also google your engines factory diameter and compare the two measurements
@eddietaylor7323
Жыл бұрын
@@Nasperformance thank you so much for your help
What grid ?
Mom and Dad must be at work , everyone in the video used the F-bombs like they just learned there first cuss word😳😂
@Nasperformance
2 жыл бұрын
Lol you must be mad that I’m younger than you and doing things like this
Did this job workout for u? just wondering , I'm about to attempt thrust washers on my pt cruiser . maybe the whole set. is it still running? any knocking ?
@Nasperformance
2 жыл бұрын
Ran great just ended up ls swaping it
How do I get the oil girdle off.i took the ten bolts out
@Nasperformance
2 жыл бұрын
For me I just came right off after the main cap bolts were out
I cuss too! Lol 😂
If the bearing spun, crank is gonna be "flat" spotted on load side. Knock will be quieter but will end the same eventually
@jaredreck882
Жыл бұрын
It will keep it from shooting out the oil pan right ? Lol I saw this video when my van was knocking I wish I would’ve listened
So the first rod is supposed to be kinda loose to we’re it shakes?
@nelsonmarquina9427
2 жыл бұрын
Nah it was just fucked up
@oscarlopez2016
2 жыл бұрын
@@nelsonmarquina9427 oh okay so you just put on a thicker bearing?
@Realofficialdee
Жыл бұрын
What he said ?^
Can I get part number for this please
Somebody tell the females you were trying to record a video?