How to Calibrate Throttle Position Sensor Using a Multimeter (Set TPS)
Автокөліктер мен көлік құралдары
This is the easiest and fastest way to set and test your throttle position sensor. Why do you need to calibrate your TPS? Well the ECU needs to know the position of the throttle so it can determine what it needs to do with ignition timing and fuel injector duration. It will literally impact the way your car drives. This is easily one of the most important steps to verifying that your car is going to perform reliably on the dyno and just driving around town. Hope this video helps.
PCEA,
Boosted John
Like, Comment, Subscribe :)
Пікірлер: 143
Forgot to mention that the correct way to test the voltage is to back probe the connector. Not cutting the insulation.
@sentientsea
Жыл бұрын
Just a heads up that you can damage your connector by back probing too much/poorly. Be careful. Trust me , I did it! 😅
@andreuys3578
Жыл бұрын
well i have issues with vehicle jerking intermittently etc and watched your video and getting a reading of 12v on my tiburon gt
@doogeerugged89
11 ай бұрын
@@sentientsea gotta have those green back prob plugs. They're tiny and i've never had an issue. I wouldnt use the blue or black ones
@leofandersoniii
3 күн бұрын
@@boosted_john please demonstrate how to backprobe. Thanks
Out of all the videos on how to adjust a TPS, this is the only one that actually explains what to do
Just wanted to let you know you saved me hundreds of dollars and a great deal of time with this video. I acquired an 89 c1500 with a recently rebuilt 5.7 after it rear ended me on the hwy. After replacing all the crushed body panels and related pieces, I couldn't get the rough idle and check engine light under control. I was prepared to start shotgunning replacement parts and sensors to see if that would help. I watched your video and thought to myself "heck, I've got a multimeter". 5 minutes to adjust the TPS...no check engine light and idles smooth as silk. Thanks guys!
@itsmegoomy2364
Жыл бұрын
I think I am going to have to reprogram mine because I didn't even consider that cleaning the throttle body would be affected. There are some great videos out there and this is one of them! Thank you sir!
At first i was really starting to get pissed off at this video. But then you guys actually put out good information. And the commenting guidelines earned you a subscribe. Thank you!
Great video. Explained it clearly. I would have liked to have seen the voltage lower or higher so you could have adjusted the TPS. But this is a professional shop so I understand.
I've been looking for a video like this for a year on how to read and use the meter to read the throttle position thanks so much !
All the information I needed and none I didn’t. Awesome work dudes!
About the only video that is simple and straight forward !!
Thank you for this video. it fixed my idle problems ive been having for over a year
Okayyyyy learning new things every day appreciate it John
I wish yall had shown how to do the actual adjustments if not getting the needed readings. That’s what I’m needing and been looking for and cannot find instructions on anywhere. This was helpful but need more data on the calibration. Thank you!
Thank You. Very helpful info. Just replaced my whole throttle body with sensor and didn't calibrate it. I have been having issues with the car running rough and some OBD2 error codes. Now I'm going to calibrate it so maybe that might help fix it. I haven't been able to figure out what has been wrong with it so it's been in my garage for quite awhile. Also I had some issues with the wiring. Thanks again for all the info.😊
Thank you for the exact voltage value.
Yeah. You are my go to guys from now on.
Great video the only that tells exactly what to do Thank you
Back in the day on my mustang 5.0 Fox body the magazine editor's recommended using small safety pins carefully pierced through the wiring with alligator clips on your DVM. These types of maintenance tips are what can give you an advantage at the drag strip.
Aye thanks for teaching me a new trick. Quicker than programming TBH.
@boosted_john
2 жыл бұрын
Yep! Pretty easy method!
Good video, it was the same as my 1991 4.3 as well.
Very helpful i needed to see this video
Very helpful much appreciated cheers
Very good information
I ported and polished my Throttle body! On my Australian V6 version of the American Buick based engine. 3.8 litre ecotec. I had a hunting on idle. As in revs were going up and down,then settled. I just lightly adjusted the throttle cable to remove any slack. I replaced a hose with silicone hose in the performance type on my CAI going from my TB to MAF sensor. Strangely it's not hunting anymore! Maybe my old hose had a vacuum leak? Also my 4L60E transmission doesn't slip like it randomly would do. I'm gonna back probe like you did. Top video! It took forever to find a proper tutorial on TPS SENSOR Setting! Subbed and liked. Cheers from Australia 🙂👍👍👍
@savitr7783
Күн бұрын
@@dragan3290 i have a buick lesabre with the base version of the motor
@dragan3290
Күн бұрын
@savitr7783 nice!! They are pretty good looking car!
Right off the bat I know this gonna b goodie I sed tpms when referring to tps alotta times holy crap that was funy
Tnxx to teach me something 🤗🤗
Hi John! 🤗 Great video! TFS LY ❤️
@boosted_john
2 жыл бұрын
Thanks momma!
search around videos, this is the best one I think. Now I am relaxed because you mentioned "aftermarket" won't be perfect, so, I am not looking for perfect one online now. By the end, the younger person explained further the key point: the full closed throttle is looking for 0.45 V, this is sooo cut the chase...
I found the little block inside the sensor that seats onto the fork to turn the throttle to be unaligned. By putting it back in the slot it instantly fixed my voltage issue. Could be the tps was put in wrong if it worked fine many times recently before.
I have a certificate in basic electronics and you can buy multimeter test leads that are pin ends from fluke, you need to be patient because the are some of the thinest wires used, I'd put it down near the plastic and patiently wait for a reading.
Great video guys. What's next if the TPS is good ?
@tylersowa3858
9 ай бұрын
Idle air control valve
Super helpful and for all cars 0.456?
I always scribe a crisp clean deep line on my old sensor old throttle body while still in place haven't had any issues just line up the marks and done
Based off what your friend said if I installed a new tps and calibrated it to .45 volts and runs a little hesitant at times I should re calibrate it? Maybe go up in voltage?
Hi. I've got a 2003 Montero Limited 3.8L. Twice so far (1,000 miles apart) mine has gone into a condition where it will not accelerate. It idles and starts fine, but will not go over 40mph on level road, and takes a long time to get to that speed (severel minutes). It will be fine one moment and then begin this malfunction in the middle of driving it, in town or on interstate. I do have a TPS sensor code (P2135) but also cam and crankshaft sensors codes. The timing system is fine and it doesn't jerk or do anything strange except refuse to accelerate. I can turn it off and after 20 minutes it will operate fine again. Is the the TPS sensor getting hot and then it fails?
So can I do this to check if my throttle body is failing on my stock b20 ?
Dont forget to check for dead spots as you sweep from .45 to 5v, i wastching a video and that was his problem it didnt go smoothly up, it went down before it went up again. The TPS is basically a potentimenter with a whiper blade that makes contact, sometimes the contact isnt good or gets corroded and you have a dead spot. I got a TPS error code on mine but no symptoms like rough idiling or low power. Except when i took it on the highway the first time, it did feel like i was pressing the pedal more then i should have... i thought this was in my head trying to be cautious with the car on the highway for the first time but maybe it is a dead spot that isnt noticable until highway speeds. I just got the car so not entirely famliar with it but noticed it was good on gas in the city, good pep too but didnt get much better milage on my highway trip which had me puzzled. Also noticeds the air injection pump relay and fuse were missing, so figured it was attributed to that, until i saw the TPS error code. Maybe it isnt a TPS issue but related the air injection pump basically being shut off. Funny thing is when i try to find what kind of relay it is(to find a replacement), all the videos of my car showing the fuse box have it missing as well, maybe its not critical... i heard it was for emissions, but also heard its for better fuel efficiencey. Anyway a slow sweep of the TPS will reveal for sure. Also heard a fast sweep can cause damage since it generates electricty. Probably being paranoid there but better safe then sorry.
Hey man so the lowest voltage i can get on mine is .72V. Now before i replaced the tps I remember trying to adjust the throttle cable to compensate for the idle issues, but forgot the ECU will do the things to attempmt a stable idle. Could i just have the throttle cable too tight causing the higher readings of .72 - 5.2V seeing that the tps is what monitors the butterfly?
correct me if I'm wrong but OEM spec says .5V full closed and between 4~4.5V full open, all depending on the ECU your using
@boosted_john
2 жыл бұрын
Makes sense. I recommend this.
@lunarxvibez3758
11 ай бұрын
Hey was curious I have mine set to .45 when closed but when fully open it’s 5.3 how do I lower it when it’s fully open
@Fearisthemindkiller617
11 ай бұрын
That seems way off, I would try full opening the throttle. Back probe the signal wire then adjust the tps based off what you get
This 2015 Chevy Spark LT I have starts, Idles, then after 2-3 mins shuts off. If I attempt to drive it with-in those three mins, it only goes 8 or 9mph. When it was purchased(used from Auction) it drove 8-9mph all the home(5-6miles away). any clues or suggestions?
Do I still need to do this with the hondata
Thanks John
The center wire is the hot wire of the bunch?
its ok to do that test with engine running idle?
Okay this looks spot on and I haven’t checked mine yet but I upgraded from a stock 64mm body to a 70mm body but when I started the car with everything in right it starts and goes right to 6-8k rpm’s so if and when I run this test you provided with us if mine is just way to high how would I drop it back down using that volt meter? Or do I need a good scanner I can tweak settings with? Please @ me!
@austinbates247
Жыл бұрын
Okay my bad totally forgot you just said you can manipulate it by moving it around then tightening back down but say it were still to high then back to my question above^
@austinbates247
Жыл бұрын
Okay so I just checked and the smallest DC volt I can get is 5.4 lol so I need to alter the bending in the tps grooves?
@mrhatchyK24
10 ай бұрын
@@austinbates247most likely yea
I bought my TPS off PLM & they said it has to be set at 1-2% open and not at 0. Is that on the Hondata side?
Do you mean the at idle position voltage should be 10% of the voltage value shown at full throttle.. I have toyota 2NZFE 1.3 L with Electronic throttle body without (accelerator cable) , I am trying to adjust throttle stop screw at idle to factory setting.
I have a 2000 Jeep Wrangler. I am getting code p0123, which is tps high voltage. I replaced the tps but am still getting the code. How do I adjust the voltage? Everything is stock
is this also doable in a L-jetronic car? with motronic BOSCH ECU?
Should the engine be warm when doing this?
Just now seeing this but are you putting that tb on the stock manifold? I’m trying to bore out my stock LS mani to put a 70mm skunk2 on didn’t know if that’s been done
@boosted_john
Жыл бұрын
Yeah try it! I’m pretty sure it’s possible!
Can you adjust it so that you have it open faster like a pedal commander? Of course it'd be locked to that setting until you readjust it..
@kevinaweseom2866
2 жыл бұрын
It doesn’t move the peddle, it only reads how open it is
Can you do this with an OBD II scanner's live data function? My TPS is reading 9.8% at idle condition (Foot off the throttle). Can I just plug in the OBD II scanner, switch it to live data, and adjust the TPS until it reads 0% at idle?
@jeffsheckells5810
Жыл бұрын
Have you tried this ?? I was thinking the same thing on my 2000 civic
Bought a new tps a few weeks ago, put it on not knowing it had to be set. Couldn’t get it to work for a few days until I moved it to the right spot I guess and the car started up but idled roughly after a minute. Drove it up into my garage and it ended up not starting after playing with the tps a few times. Found this video and got mine set to 0.45 and 4.97 when open throttle but the car still won’t start. Confused now
@tristanbullock7547
3 ай бұрын
Did u figure out what it was
Mine has 4 wires, so no middle wire. Which wire would it be e2 or IDL?
How about ford lynx..is it 4.5 volts also....
Almost listened to this guy until I saw what he did to wiring No professional would do that
thanks
@boosted_john
10 ай бұрын
You’re welcome
Does this work on any vehicle? These numbers? I have a 97 Tacoma and I replaced the throttle position sensor and now it idles high.
Can a bad tps sensor cause a high idle??
Is that Mark from what used to be One6 motorsports?
I assume that if I need to adjust the voltage to match .45 I just move the tps by the slots accordingly
I'm running a link ECU on my EG. You can calibrate the TPS via the ECU on the Laptop!
@DJ_Driven
2 жыл бұрын
Been thinking about going with a Link ECU for my Evo 8.
I did this mine is at .45 when closed and 4.5 when opened and now my idle sits extremely high ?? Any ideas?
No clue if y’all will reply…but I’ve got a truck that needs to be calibrated but there’s 6 wires vs 3 into the TPS. Which would I connect to? I believe they’re addressed at TPS 1 and TPS 2 with each exact placement letters A-F
@boosted_john
Жыл бұрын
Not sure. You would need to find a wiring diagram for your engine harness and locate the tps signal wire
So do you still have to disconnect the negative terminal to caliberate the tps?
@mrhatchyK24
10 ай бұрын
I don't think they did.
Hi I'm jv I saw your video how to calibrate the tps sensor...ok how do I calibrate the tps sensor and the idle screw in my honda civic 1.7l 2002 .....if I can get help with this problem I'll appreciate thanks I hope you can make a video and if can send it to see.... thank you.
@mrhatchyK24
10 ай бұрын
He just explained how to calibrate tps. There is a idle screw on the throttle bottle. Look it up on Google it should pop right up
What type of multimeter is that?
You shouldn't strip any wire insulation away, you are opening up the wire to corrosion or you might have a heavy hand and cut some to the wires. I would like this video if you had just used a paperclip inserted into the connector.
Silly question but how do you adjust it if it’s not right?
@Chuys_Rd1
Жыл бұрын
Loosen the bolts and turn it left or right
So this could be why my 2016 Chevy Cruze hesitates when I hit the gas? It takes a full 10-15 seconds after I hit the gas for the car to actually start moving
I have 74mm skunk2 throttle body and i buy acuity tps sensor for my rsx and whe i plug the tester it shows 4.69 any suggestions why is so high? Thanks
@lookronjon
2 жыл бұрын
The wires are probably mixed up. Find the wiring diagram for that TPS and check the plug.
Im getting 0.50 at closed and 4.25 at wot. Any help?
So, if the numbers are not within that range, do you rotate the sensor to and fro? Thanks.
@boosted_john
Ай бұрын
Yes
Question, my battery is relocated to the trunk. Can I use the negative terminal on a spare battery that is not hooked up to the car?
@vostok2017
8 ай бұрын
Просто прикрепите отрицательную клемму DVM к кузову автомобиля.
What about in a 2002 honda civic 1.7 vtec is it the same .45 or is different reading
@mrhatchyK24
10 ай бұрын
Probably is. Or right around there
That voltage of 0.4, something it's for any car?
I can’t get mine in spec, the voltage is jumping up and down at idle, and WOT won’t go over a volt
Should you have voltage when the key is off?
@dylanrice8662
Жыл бұрын
No
Okay so.. if I just pay attention to the close number (0.45), tighten the sensor, would it automatically be 4.5 at full throttle?
@boosted_john
4 ай бұрын
It should be very close if not spot on.
Man how much volatage is suppost to go to that middle wire i get zero on a b18 non vtec
So how do you adjust these voltages? Is it only by rotating the sensor?
@boosted_john
2 жыл бұрын
Yep
@erniecarrasco9107
Жыл бұрын
So you can change the rotation on the sensor and the voltage also changes. Then you match your max and minimum throttle plate opening to the desired voltage? This video makes it seem like it was already calibrated correctly.
@mrhatchyK24
10 ай бұрын
@@erniecarrasco9107they said it was already calibrated. They explained everything tho
@erniecarrasco9107
10 ай бұрын
@@mrhatchyK24 thanks
How do you actually adjust the voltage when it’s reading incorrectly to get it to .45 ? What do you adjust? I wish you showed how n what you calibrated to get it set right that’s where I’m lost 😞
@boosted_john
7 ай бұрын
You gotta rotate the tps
What if there is two centre wires?
Can an incorrectly set tps cause a car not to start? Or almost starts but immediately cuts out?
@boosted_john
Жыл бұрын
Probably
My 06 Kia Sedona has way more than three wires so I can’t do the center wire
Ciao ho una Nissan Primera 20egt anno 1991 150hp mi potresti dire il valore di calibrazione del mio TPS per favore grazie
Damn I set mine to .5 at idle and 4.4 at full throttle
@pigeonsil240sx
Жыл бұрын
you could set it to 4.5v at wot,then use the idle screw to set the closed throttle to 0.48v
Can badly wrong ajusted or not adjusted tps on hondas cause ecu limp mode?
Mine is at .46 and dies not adjust as far as I know it's stock
Hi, one say 0,50v other say 0,45v. What is right ? 😅
Ami me llegan solo 4.0 volts
Mine is always reading -0.400 and doesnt move from there
Mine has 4 wires
You do realize you can calibrate it on S300 right
@yavenpersaud6153
Жыл бұрын
Hey just got s300 is this true?
It's .5v closed not .45??
@christophersanders5007
Жыл бұрын
I need to adjust a TPS on my Mitsubishi. I am going to try both .5 and .45 volts to see which one feels better. When I was a fleet mechanic on diesel engines I would set the TPS at .5 V closed, and forget the open throttle sweep because factory tolerances the wide open setting would always be off, and it did not effect performance anyway...only the closed setting mattered.
@FroztiProductions
Жыл бұрын
@@christophersanders5007 yup exactly adjusting open throttle is pointless anyway, ecu is using map or maf when you're wide open so just get closed throttle perfect and call it a day. Every other video I've seen is .5v but I have the factory service manual so I'll check.
Are you qualified technician or just hit and run mechanics.😂
1st.
This y ur cars never run go take it to a professional
god the camera wok is awful
You can't be qualified mechanics. Very poor video with mis information etc etc.
@mrhatchyK24
10 ай бұрын
I guess you aren't either if your not gonna explain what they did wrong