"Never skimp on perfection." OMG that's my new motto for life!

Very nice! Foil, mesh, staples and mastic... impressive. I've got an apprentice I'm trying to untrain from some knuckleheads that taught him that foil tape and mastic are a good recipe. We just changed out an evaporator coil that was installed that way and I literally tore off a continuous 48" piece of foil and mastic joining the furnace and transition to the evap coil. I told him that if I came back to QA/QC a job that I sold and someone did it that way, they get ONE MULLIGAN and the privilege of me checking every job for the next 30 days. Any further excursions, the tech will come back and do it right and receive minimum wage for the training while they do it.

@512kjt

3 жыл бұрын

Subbed ya!

Hey, thank you for taking the time and effort to produce this excellent, easy to understand, video tutorial on how to properly create a duct run from duct board using the AmCraft tools. Keep up the good work!

I that part where you say PAY ATTENTION.hahah. You should be commended for having to do that with a hard hat on that didn’t fall off. I have been trying to enforce wearing hard hats for 8 years and the ac guy is only one that said he can’t wear one. Well done

Nice job!

Really good video thanks

Thank you!! Bad ass video sir

Thank you so much. This was extremely helpful.

@howtodothings8415

4 жыл бұрын

Glad You find this helpful. I appreciate you!

Thank you my friend really helped me

@howtodothings8415

3 жыл бұрын

Glad to hear!

"Never skimp on perfection" A true peofessional.

Thank you very much.

Great vid

I have a question…. This video is quite old …. Are you still monitoring your channel? Great video by the way. Good timing, right to the points, and. Not filled with not needed information. 👍👍 If you’re still taking questions let me know and I’ll ask. Take care.

Nice

this is amazing! thanks for sharing! Is this how you can construct a hvac return box?

@SirHumano97

3 жыл бұрын

This is how you make any duct box, the use is up to you. Plenum, return, trunk line, etc.

So for every cut you make you have to add an extra 5/8 of an inch and how much should I leave for the overlap of foil paper 4 inches is enough

I've read a lot of negative opinions on ductboard... but it's old information. I was thinking of using it because we are moving our package unit. Would it acceptable for extending our trunk line in the crawlspace?

TIP: Keep the factory end (flattened side) closest to you. It's much easier to start the cutting tools on that tapered side verses the straight side.

@howtodothings8415

4 жыл бұрын

Michael Yolch absolutely. Also, if you run the ship lap tool backwards it will not come out correctly.

Thank you for your awesome video nobody on you tube explains it better then you sir! im still a little confused though could you please help me out I HAVE 1" 1/2 RED TOOL AND 1" 1/2 BLUE TOOL IF FOR EXAMPLE I NEED TO MAKE A 20X20 PLENUM HOW MUCH DO I SUBTRACT OR ADD TO FIRST CUT? AND WHY DOES AMCRAFT INSTRUCTION SAY TO ADD TO EACH MEASUREMENT PLEASE HELP SIR THANK YOU IN ADVANCED NEW SUBSCRIBER HERE!!!

@howtodothings8415

5 жыл бұрын

Vasquez Soccer Squad if you need the duct to be 20x20 inside dimension then you would just add around 1/2” to your first cut. If you need it to be 20x20 outside dimension you would subtract 2 1/2” from your 20x20. So it would be 17 1/2” x 17 1/2” but you would add 1/2” to your first cut. That’s what I do with my tools and it gets pretty close to perfect. Technically you should be adding 3/4” to your first cut because that is half of 1 1/2” but there are so many variables that come into play such as the pressure you apply, how broken in your square is, and the conditions of your cutting tools. Also, technically, if you are putting perfect pressure on your tools you should subtract 3” from your outside dimensions. I subtract 2 1/2” because that’s just works out for me. I hope this helps!!

Good job bro...I'm sure you're using an outward clinching staple gun and not a standard one right? Normal staples work themselves out of ductboard or so I always heard, so we've always use the outward clinching ones

@howtodothings8415

3 жыл бұрын

Thanks! Yes, we use an outward clinch stapler. The outward clinching helps hold it all together. It's also good for insulation around metal duct.

Why did you add 5/8 of an inch to the initial and only initial cut? Also what size ductboard was this 1" or 1.5"

Use a table counter top height to save your back.

@howtodothings8415

4 жыл бұрын

Thank you!

Do you have one based on the two 45o bends making a 90o bend?

@howtodothings8415

4 жыл бұрын

I can make one!

Right here in Texas is not allow to use tape and mastic. Once you put the staples , you can choose to use or tape or mastic on top, but not both, or inspector reject job.

@howtodothings8415

3 жыл бұрын

Joseph Schneider yeah it’s different in certain regions.

@howtodothings8415

3 жыл бұрын

Joseph Schneider I would love to not have to mastic 😂

@joeschneider67

3 жыл бұрын

@@howtodothings8415 agree

@chrischeek2963

2 жыл бұрын

@@howtodothings8415 Then how would you ensure an air tight fitting?

@howtodothings8415

2 жыл бұрын

@@chrischeek2963 duct leakage test

Where can i find Duct Board like that. Im only seeing small pieces?

@howtodothings8415

2 жыл бұрын

HVAC supply house.

@oneshot_onekill4618

2 жыл бұрын

@@howtodothings8415 thank you. I can use this to run a duct from my existing duct work to my garage where i put ky new air handler is that correct? About 5ft

What kind of duct board is this?

I'm confused. Some places say do not put mastic on top of foil tape. Please explain.

@howtodothings8415

4 жыл бұрын

It is required by code to apply 181 mastic on all joints in my area.

Doesn't the measurements change depending what size duct board thickness?

@howtodothings8415

3 жыл бұрын

Correct. This video is for 1 1/2” ductboard. I take 5/8” off at the start and it always works out for me. However, mathematically it should be 3/4”. For 1” duct board I would take off 1/2” and see how that works out. Trial and error. Also, you would need 1” tools for 1” board.

whats the name for theme sheets and where do i find theme do they only come in 4x8 sheets thanks

@howtodothings8415

3 жыл бұрын

they come in 4x10 sheets. its called duct board. you can find them at your local HVAC supply house.

@julianvillegas2190

3 жыл бұрын

thanks for information

Where can I buy the duct board sheets at though?

@howtodothings8415

3 жыл бұрын

Google “hvac supply house” something near you should pop up

@PurrrfectWorld

3 жыл бұрын

@@howtodothings8415 thank you.

How do you do outside dimension?

@howtodothings8415

7 ай бұрын

The total width of the duct will be 3 inches larger than the inside dimensions. So if the duct is supposed to be 16”x12” the outside will be 19”x15”. This is because the duct board in this video is 1 1/2” thick. Add the two sides or the two top and bottom together and you get 3 inches. If you need the outside of the duct to be 20”x10” then you will need to find the inside dimensions to make the cuts. In this example you would subtract 3 inches from both the 20” and the 10” and your inside dimensions would be 17”x7”. Then follow the directions in the video to cut the duct board. Hope this helps!

@howtodothings8415

7 ай бұрын

Remember, everyone cuts with a little different pressures on their cutting tools. It may end up being a little off. Adjust accordingly.

@onlyulee866

7 ай бұрын

Do you still use the right side as your mark

Why you did extra on the measurements for the first cut

@howtodothings8415

4 жыл бұрын

The first cut requires the extra measurement to compensate for the overlap of the shiplap at the end of the duct.

Buy the machine......

When a dude on YT is telling you how to do a job and his tools are all beat up, you should listen to what he says. Thank you!

this could have been a 2 minute video , I cant believe you forgot to tell us the story about your grandchildren !