There is one serious design flaw with this device: Once you own one, you will get an uncontrollable urge to demolish every single rock in a large radius around your workshop. I doubt there is a single rock left, larger than a foot across, within a five mile radius of where those guys live.

@greengoat5654

2 жыл бұрын

Ape instinct

@spaceguyreal

2 жыл бұрын

@@greengoat5654 ooo o0o o00 000 0O0 OOOO OO OOO

@tommychappell6359

2 жыл бұрын

Hahaha.. that's me...

@CMAenergy

2 жыл бұрын

Is there one for Trudeaus incompetency?

@skylark4901

2 жыл бұрын

💥"Hey!! What are you doing in my backyard!!" 😂

Over 30 years ago , my Father & I, were removing from the garden a large wedge shaped section of the garden to build a car port. We found a large rock that was about 2 meters in diameter. We had drilled about 20 holes in it to try to split it. We put in steel pins at try to burst it and hit them with hammers, that didn't work. We were working on it early on a Sunday morning , when my Grandfather turned up with a shotgun shell, he had replaced the shots with a single lead shot. We drilled one hole out a bit larger and put the shell in it , he then hit the shell with a hammer and the blast split the rock. Shortly the neighbors were out of their houses wondering what the load bang was. We said it was the rock splitting.

@generalzugs6017

2 жыл бұрын

You should have said it was the beans from yesterday's lunch.

@user-gv2ne7vk8x

2 жыл бұрын

Здравствуйте! Я много работаю с крепкими валунами из кварца. Можете подсказать, на какую глубину вставили патрон? И как привели в действие взрыв?

@robertwillis4061

2 жыл бұрын

@@user-gv2ne7vk8x we drilled about 15 -20cm down and used a large screwdriver which he struck with a hammer on the firing cap. I can't remember how far , but the screwdriver when about way up and landed down the street a bit

@MaFed191080

2 жыл бұрын

@@robertwillis4061 Спасибо. Теперь понятно зачем нужен дополнительный вес на другом конце штыря.

@andrewburnett8743

Жыл бұрын

my neighbors around here would not bat an eye

As a kid of 10 in the seventies my uncle and grandpa taught me alot about explosives,How to shoot, hunt fish,and fire a howitzer etc, all the things a kid needs to know. My uncle, ex military and a miner, showed me how mining worked by doing exactly what this guy is doing, exactly! Years later a good mate bought a remote property somewhere in Australia. He wanted to build a small house in one of the cragy areas. We,he, I and numerous good mates, have built a 6 bedroom 3 story house / Cave. We kinda upscaled this technique a 'little bit ', just a tad. When the temperature is hitting 46° in the shade it's a steady mid teens in the lounge and bedrooms . Anything is possible with the right tools/skills and most importantly, Attitude.

@kevinbyrne4538

Жыл бұрын

Every grandfather should teach his grandson how to fire a howitzer. ; )

@CowboybubPercussion

Жыл бұрын

@@kevinbyrne4538 vi va revolusion

@fiokgoogle8779

Жыл бұрын

Im interested , because i have an inclined mine shaftt it must be timbered and maybie down rock blasted , i was unable to finding how in the old mimes was the timber wood poles set properly

@leonardovasconcelos4856

7 ай бұрын

dam i am jealous of that knowledge.

Genuinely a good idea. Having spent 6 hours breaking down a boulder with an electric hammer, i know that this is muh faster.

@morganberlin4610

3 жыл бұрын

6 hrs lol I could have done it 15 minutes or less with electric jackhammer come on....

@MannoMax

3 жыл бұрын

@@morganberlin4610 Yeah, not that one. A small Makita hammer drill, working on a 45° slope, alwhile making sure the boulder doesn't go tumbling into the guys house.

@morganberlin4610

2 жыл бұрын

@@MannoMax a 45° slope breaking the rock like that would make it fall into a guy's house easier

@thomasschwab1727

2 жыл бұрын

@@morganberlin4610 how can you know that without knowing the size of the boulder, type of rock, and surrounding conditions? You sound like the guy who always has a story to top all others. Usually the result of a small tool and a track record of dissatisfied women.

@morganberlin4610

2 жыл бұрын

@@thomasschwab1727 🤣🤣 story top other I'm private contractor . Called talking from experience dummy . I don't need know type rock or surrounding conditions . I know what takes get job done how get done efficiently

I saw a black powder log splitter my grandfather made, at the time I didn’t know what it was used for. Thanks for sharing!!!

The top of a BIG rock was sticking up out of the ground in the bottom of the hole where my septic tank was to go. I hammer-drilled a series of holes a few inches apart around the perimeter of the rock-top at the dirt level. Then I hammer-drilled two larger holes (1/2" x 4" deep) straight down from the top. I blew the dust out of the holes like in this video. Then I put a fuse in each hole and packed 100 grains of black powder in each hole. The two fuses were exactly the same length. I filled the holes to the top with sand. I put an upsidedown wash basin over the rock with cast iron weights on top. I twisted the fuses together and lit them and climbed the ladder out of the hole quickly. After it blew, the wash basin was shredded and the top of the rock was blown clean off, flush with the ground. Not the easy way but it was fun and it worked.

Clever... But next time, draw a line on the rock or concrete, and take your hammer, and hit the rock on the line, starting at one end, work your way to the other end. These hammer hits do not need to be hard and heavy hits, just many of them... When the sound changes from higher pitched "PING", to a "THUD", give one last hard and heavy hit with the hammer, at the opposite end your last hit was that you heard the sound change to a "THUD", and hit right on the line, and the rock or concrete with fracture right along that line. Often times, the fracture line will appear as if it was cut with a machine, due to how flat it is, not always, bit often... The thicker the material is that you are trying to fracture, the longer the tapping will take. A 3 foot thick by 10 foot long slab of concrete, may take 5 to 10 minutes to split down that fracture line. The harder the rock material, the faster the fracture line works.. Good luck...

@a_real_jive_turkey7772

3 жыл бұрын

Relax. You take me too seriously

@a_real_jive_turkey7772

3 жыл бұрын

Plus that's more than I want to read so I'm just going to agree with you. I feel like a better title would've been like "How to build your own Boulder Buster"

@henryrollins9177

3 жыл бұрын

You know what your are talking about man..! 😀👍

@royalt9615

3 жыл бұрын

Couldn't agree with you more just grow some balls and learn how to swing a sledgehammer. But I understand these types of guys that keep their hands well moisturized

@rorschacht8478

3 жыл бұрын

@@royalt9615 work smarter not harder

very good idea . I advise you to add water to the hole several times and let it be absorbed by the rock to maximize the effect of the pressure. the incompressible water will have the effect of redistributing the pressure of the explosion in a more efficient manner.

@samuelmellars7855

3 жыл бұрын

While adding water to the hole and letting it sink in might work to improve the fracturing of the rock... Water is *not* incompressible, especially compared to rock.

@bobbypatton4903

3 жыл бұрын

@@samuelmellars7855 water is very much do incompressible.

@cr4zyj4ck

3 жыл бұрын

Those charges aren't waterproof. Don't wanna get them wet, they won't work. Water can seep in through the crimp and totally ruin them.

@wolffang489

3 жыл бұрын

@@cr4zyj4ck the idea is to let the water soak into the rock and the blank is only there for a minute at most. Soaking the powder shouldn't be an issue.

@Warhawk76

3 жыл бұрын

@@samuelmellars7855 water is absolutely not compressible

Use eye and face protection. Drill holes in a line along or with the grain of stone.(looks like wood grain only less obvious) get oak or ash dowels and insert them into holes they should be tight and have to be tapped in. Soak tapped in dowels with water. Let wet sponges rest over holes. Works faster when temp gets freezing at night/day.

@wolffang489

3 жыл бұрын

That's a good solution during half the year in the North.

@mr.shannon6137

2 жыл бұрын

Or fill hole with expanding grout, which is designed for that. It's quick and fairly cheap.

@TheWtfnonamez

2 жыл бұрын

very clever. I have seen this technique done in quarries with pins and a hammer. But letting dowels create the load is a lot less effort.

@tommychappell6359

2 жыл бұрын

@@TheWtfnonamez which load? Oh right take the load.. I see.. using screw and pieces of dowel instead of long spike..

Love the sims-like conversation in the field

Good to see another person like me who can’t be bothered moving drive belts on pedestal drill when you go to a bigger drill size 😂Full noise and send it! 👍🏽👍🏽

Love it, Basically a scaled down version of how mining is done.

that was amazing i have been trying to break a few quartzite boulders here in the philippines, wish i had access to that equipment, gave you a sub

I had to chuckle a little bit when "the easy way" entails owning machining equipment and fabricating the tool first. That said, a single .22 will drive a nail in concrete, so the power is there to be exploited. I like the idea of the weight that the charge cannot overcome as a breech block. Your guards seem completely workable to me. It does not look very controllable as to what breaks where from what I could see. Pretty cool.

@MaFed191080

2 жыл бұрын

Закалить пруток можно и нагревая его в костре, закаливать в любом старом машинном масле или растительном масле. Возьмите пружину или торсион 8 мм. От старого автомобильного амортизатора например 2евро. Болванку (утяжилитель, груз) можно сделать из кувалды или залить свинцом банку и закрепить на прутке обычными хомутами. Это груз чтоб при отдаче не улетал штырь ( пруток), как снаряд. You can temper the rod by heating it in a fire, temper it in any old engine oil or vegetable oil. Take a spring or torsion bar of 8 mm. From an old car shock absorber, for example, the price is 2 euros. A blank (weighting, load) can be made from a sledgehammer or pour lead into a jar and fix it on a rod with ordinary clamps. This is a load so that the pin (rod) does not fly away like a projectile when recoiling. Sorry for my English.

@Qingeaton

2 жыл бұрын

@@MaFed191080 Your English is very good.

@kevindouglas8768

Жыл бұрын

"Easy" means having a friend with a forge to harden my materials for me, does it?

Thanks for your interesting approach to story telling! Anything that explodes; I like.

Guys, you saved my life!!! Thanks!

The more restricted the access, the better of an idea this is. I'm delighted to try this out on a small tunneling project. Thanks for the idea!!

@twestgard2

2 жыл бұрын

Tell us more about this small tunneling project…

@antkoz6370

2 жыл бұрын

@@twestgard2 go start your own.. We will all connect at some point

@Arcanefungus

2 жыл бұрын

And you need a rod with plenty of mass... My first thought was to just use a big ol nail, but said nail will turn into a projectile...

@raptorkravmaga9977

Жыл бұрын

@@twestgard2 🤣🤣🤣

If this is the easy way, I don't wanna know the hard way.

@ReasonAboveEverything

3 жыл бұрын

Hard way us to drill 3 holes instead of one and pound in metal wedges which is the easy part in that.

@Nevir202

3 жыл бұрын

@@ReasonAboveEverything Nah, hard way is with just a sledge hammer lol

@beforelifewaschaos

3 жыл бұрын

Drill holes by hand and put wooden nails in them, then pour water into them 😄 it's also one of my goals for my bushcraft project ^^

@d0peghost224

2 жыл бұрын

i burned out the motor on an electric jackhammer and blistered my hands the hard way, whilst making minimal progress lol

@Dr_V

2 жыл бұрын

This is ONE way, reasonably easy but not necessarily the cheapest or the safest option. Use a larger drill bit (12 to 20mm, the larger the better but depends what your tool can handle), than insert a dry wooden stick of the exact same diameter into the hole and start pouring water on top of it. It takes a while but it will eventually split the boulder.

This is the best way to split a big rocks I've seen on KZread, thanks for this great idea 👌

Amazing idea, will definitely try it for sure

I've been a crusher operator for over two decades never had this much trouble breaking a rock...

@FlyinBrian777

3 жыл бұрын

@George AKA Dad How much does that crusher earn for the owner in a year? You called the contest too soon.

@rorschacht8478

3 жыл бұрын

@@FlyinBrian777 I was going to walk to the store but by your logic I'm better off just renting a helicopter.

@sa.8208

3 жыл бұрын

Richard getting finessed like a little bitch here by chris chris

@richardcrow3042

3 жыл бұрын

@@sa.8208 talking like your education from the penal system

@richardcrow3042

2 жыл бұрын

@@sa.8208 I'm completely blind now in my ages but I manage to skydive ride a bicycle and yes manage to text back with intelligence there is no contest just accomplishments...

Awesome, just awesome 👌 Loved it. Don't care how long it took to build the tool, still freaking cool

Very much impressed loved it

Great, satisfying video

I recently took out the concrete Boulder that I used to bolt our mailbox too and it was a little bit more than twice as heavy as I could lift. I drove six holes in it and I used six railroad spikes to wedge my way down in there, and yes this would have been much faster but exploding rocks can get kind of dangerous especially if you're around cars, your kids and your house.

@Kumquat_Lord

2 жыл бұрын

Use demolition grout?

As a miner I must say im really impressed. You basically made the poor mans version of the Sierra Blasting System but I think yours actually works far better

Wow that's awesome 😎 cool .I can't believe .

Most excellent information on an invention love it !

Some bum and done - very clever idea, nice work . super !

@Dr_V

2 жыл бұрын

Yeah, great if the rock is fully compact, but if it's already cracked inside (or a more brittle type of material) you may end up with shards flying around like shrapnel.

@derekmulready1523

2 жыл бұрын

@@Dr_V Hence the Blanket

Přesně tímhle způsobem jsme před 20 lety pomáhali, s kamarádem střelmistrem, jeskyňářům udělat průchod z jednoho systému do druhého...a koukám, že se to u jeskyňáŕů uchytilo 8o) Fajn video!

Excelente idea 👌👍💡

Cordless hammer drill and expanding grout

@adfadgaqgv

2 жыл бұрын

I'm pretty sure I read your comment before watching this, went and youtubed expanding grout, bought some, successfully used it and was actually very surprised by the result. So I guess I'm back here to watch the video

@datrooster4112

2 жыл бұрын

@@adfadgaqgv i got the info from "ask jeff Williams" channel he has a lot of great info. I too was surprised with the results

This has a distinctly Russian mood to it. Lol. Well done!

@andrejohnson6731

3 жыл бұрын

I believe Kadlec is a Czech surame, not Russian. I might be wrong

@NVArt001

Ай бұрын

For some reason the Finns love explosives as well. Must be the proximity.

Very cool ! I want two. I know a few people who would love to have have this for removing big rocks and old foundations

Awesome! Cool idea, great execution!

I bet you could use those hilte rounds that are for driving nails into concrete

@2StrokeMadness.88

3 жыл бұрын

Thats what they are

@lanceharsh7025

3 жыл бұрын

Good point

@johnosman8971

2 жыл бұрын

Yes, it is a .22 cal blank, … and it is the percussion from the cap that will break the rock, … having a good, concrete, rock bit is essential, but one need not necessarily have to drill that deep into the boulder, as if after the shells are placed, place a straw, or some type of flexible tube, down into the hole, fill it with water, & place some type of an insulating accouterment in the path of the blast, … that rock will split just like a jeweler cutting diamonds, … they use a “face drill” in the underground coal mines, then tamp the explosive, into place, & then fill the balance of the depth of the hole with a flex bag, and fill it with water, tamp it in tighter, then blast, … the whole “face” of the wall will shatter, then they come in with the mining loader, which claws pretty much everything up off of the floor in front of the face, & then loads it onto a loader transport, … or they buy a miner which hydraulically removes the face, with either a ball type miner, or a drum type miner, … it has the crab claws that rake everything into the back of the mining machine’s container until a loader gets there, a good miner operator can make anywhere between 15, to 70 feet into the face each day, if there is a loader ready to get into position, a few minutes after the previous loader leaves, … depending upon the type of strata they are removing, … then, there is also a short wall miner operation, where the roof, of the mine, is allowed to collapse in behind itself as they mine through while following a vein of whatever ore they are attempting to remove, … it is all, very, very, dangerous/hazardous work, … and more miners have been killed, over the eons, than any other trade, … I would surmise, because the planet is not so hospitable to those looking to disturb Momma Nature’s disposition’s, … breaking rock, depends on its composition, hardness factors, & the locations where you are trying to extract it from, … such as the permafrost areas in the far north of our planet, where methane is being released due to global warming, … of which I do believe that mankind has had a larger part in the resurgence of warming our planet by our movement towards progress, ever forward, yet losing the planet over a few inches of progress is most disturbing, … perhaps, one day our governments will ban all activities regarding the use of any types of fossil fuels, and restrain mining operations to the untold numbers of asteroids in space, … bringing only the proper types of ores in/around our planet, until they could fully make all operations deplorable in space, …

The Rock splitting part was truly easy, the tool making part not so much, haha!

super cool idea thanks

Great Job - looks like fun !!! 🙂😎👍

Good video production, I like how you tell the story in every language without a single word. It would be a good idea to also use some earplugs when using that tool, especially when using it underground.

I usually just throw mine down really hard but this works

@thefreedomguyuk

2 жыл бұрын

You can't set them off by throwing

This is brilliant.

That is really an amazing good idea

Hey just a friendly annoying reminder.. your bits will last so much longer if you use more cooling liquid.. sweet build btw

@carpediemarts705

3 жыл бұрын

There are a lot of people who just don't know that drilling requires oiling. They don't tend to stock oil in the drill section. Deliberately?

@lifeimitatingdeath3608

3 жыл бұрын

@@carpediemarts705 good point.. and yea, most likely.. why would hardware stores want your tools to have longer lives?

@bradfader691

3 жыл бұрын

Tapping too. Noticed he didnt put much if any of the taps. I drown my taps and drills with fluid.

@carpediemarts705

3 жыл бұрын

@@bradfader691 didn't know that

@carpediemarts705

3 жыл бұрын

@@bradfader691 didn't know that

the machining was overkill, but the overall idea is good. thanks

Good job it gives me so many ideas thank you

Wow awesome!

Bigger version made in South Africa called a Boulder buster, safer than hitting with a hammer which one day will get slung back at the user.

@2StrokeMadness.88

3 жыл бұрын

Naw them little .22 rounds don't have enough force to push that ram back at you. Especially with that counterweight. I used to fire these off cement walls with a sling shot

@damianlund395

3 жыл бұрын

@@2StrokeMadness.88 exactly 👍

@per.kallberg

3 жыл бұрын

@@2StrokeMadness.88 those are most likely .32 comes with up to seven grains of load. Used in caped bolt guns to destroy the brain of an ox.

Poor stones... Stop killing them beauties!

@stephenk.5839

2 жыл бұрын

When one of them stone beauties gets in my way, I just gots to kill em.

Great idea 💡

Great idea!

Крутяк ! Повеселились и работу сделали . Почему-то напрашивается вопрос - на производстве несчастные случаи были ? Технология явно рабочая но опыт в данном направлении должен быть .

@gangsta-free-lancer

Жыл бұрын

Да проще и надёжней колоть эти камни монтажным пистолетом если уж так приспичило патроны поюзать.

instead of using a hammer couldnt you put a second weight onto a second rod out of the top that, upon being released by a washer or pin pulled with a string drops down and hammers it home without you being in the danger zone

@stoney3694

3 жыл бұрын

It’s a very small caliber, eye safety is about all you need, having busted up thousands of stones as a mason it’s not very dangerous

@cr4zyj4ck

3 жыл бұрын

The heavy rubber conveyor belt piece they've got is all the protection they need from these blasts. The powder charge in each little case is about equal to a .22 long rifle. And the heavy weight on the end keeps the rod from becoming a projectile.

@PranaTech

2 жыл бұрын

That’s a great idea but would take all the excitement out of the process!🤣👍

Great idea 👍

That’s awesome.

I blew the top of my thumb off playing with them as a young buck, probably very lucky my lesson was limited to that injury. Good times

@Happy357mag

2 жыл бұрын

When I was a kid I had one go off in my hand when I was prying open the crimp. A lot of unburned powder peppered my hand. I was lucky I didn't lose any fingers.

Interesting ... amd a little alarming. Like using a shark-stick on a Great White. There is a commercially produced system called Boulder Blaster, which adds a very useful component. By simply filling the hole with water, the hydrostatic shock amplifies the shattering effect significantly. I wonder if you could try it out?

@Shad0wBoxxer

2 жыл бұрын

Unfortunately the .22 blanks are not too waterproof

@chrispza

2 жыл бұрын

@@Shad0wBoxxer Candlewax?

@Shad0wBoxxer

2 жыл бұрын

@@chrispza now thats using your noggin ;)

@littlehills739

6 ай бұрын

@@chrispza ping pong balls acetone lacquer

Fantastic video.

I love the way you make your vids, now subbed

What is the shell u use? Where can u order them? I use expanding grout and it worked ok . That looks fun!!

@richardjerrybest

3 жыл бұрын

Google Ramset 22

@ghost2coast296

2 жыл бұрын

you can buy these at the hardware store they're used for specialty nail guns

Love the editing and style! I would have only tip-hardened it and made it a slide-hammer. Put a couple stops on the shaft, and left the weight do the impact… But then again, it’s much easier to use the 10,000 year old “hole wit rock splitting wedges” way, or gunpowder, wadding, and fuse way…

Super věc, taky si takový nástroj musím opatřit😁

Brilliant Vid ! Thank you

That is a very smart idea! Thanks for showing us how to do it easily!

interesting. I have spent hundreds of hours splitting rock with drilling and wedges/feathers it works ok for a small boulder but a larger boulder needs say 3 drillings and you can lose the wedges in the rubble. But if drilling granite that is not a separate boulder you can spend hours trying to rescue the feathers when the rock does not fully split.

@UpcomingJedi

2 жыл бұрын

To help not lose your wedges, paint them with flourescent paint so you can find them easily. Then after every break, account for your tools each time before someone distracts you and you forget to find them.

@myotherusername9224

2 жыл бұрын

has anyone ever put a leash of wire with a flag attached on their wedges?

@myotherusername9224

2 жыл бұрын

@@UpcomingJedi has anyone ever put a leash of wire with a flag attached on their wedges?

@kennethjackson7574

Жыл бұрын

There are new ones that use a thick rubber o-ring to hold all three parts together, but the fluorescent paint idea sounds good, too.

Works Everytime,or use potassium perchlorate and aluminum powder and just a fuse

Gracias. Lo pondré en práctica. Cuernavaca. Morelos MÉXICO

@josewagostolopez7510

3 жыл бұрын

Eso sí la roca es blanda ... porque dónde vivo hay piedras de río que son durísimas y no le entra una barrena.

I heard about a similar technique, I was afraid to try it because one of his friends nearly lost a hand (major injury). I don't remember exactly how they were doing it, but you're improvised blast shield looks pretty effective and safe. I prefer to use more gun powder and be far away from the blast. I'm doing it in a cave, so I'm more nervous about the surrounding rocks moving. Very cool to see how you do it. (Hope you can read English) 🤣

@cayrick

Жыл бұрын

I bought a kit similar to this and am afraid to use it. I have lots of granite rocks to break and fear something going wrong. Instead I try drilling which is very very difficult and then use the wedge and feathers. Am I stupid?

@promaucae9890

Жыл бұрын

@@cayrick just put on more gear, and helmets and stuff, you will feel safe and be safe xd

@Hellsong89

Жыл бұрын

@@cayrick You can run this remotely if you want to be safe. Just setup the steel dovel, build frame you can setup accurately on the ground and then ether just release sledge that is mounted on bearings, or for repeated hits build pulley system that allows you to reset the sledge after each time it hits. That weight on the dovel is pretty required or you turn this into improvised mortar and might shoot the dovel out, then again rock is out to give up before "chamber" pressure get high enough to get that steel rod moving. For bigger bangs maybe 9mm version, though getting hit into primer might be issue.

I thought this was about breaking rocks some thing about the easy way

@timothywalters7237

3 жыл бұрын

Good thing I read this comment b4 I got to far into the video

@raulsocasbeltran316

3 жыл бұрын

988⁸

Gracias felicitaciones y siempre adelante

Good... and. .. Super... 👍

a neighbor kid did this with wood when i was a young. he used a machine gun round we found on the road side. works like magic until his mom found out how their aluminum cauldron got a hole. 😂😂😂

4:10 сегодня мы будем закаливать сталь-пластилин 3.

Always be precise

Excellent

The fun starts at 6:45

Hahaahahha amazing! I wouldn't call it "easy" though... you need a whole lot of complex tools and proceses

@johnnycampbell3422

3 жыл бұрын

Ever broken large stones with a pick? I have. That stone would take hours of hard work. Of course a > $150,000 excavator would be easier (depending on access) but that is also a complicated tool.

@juanistella8469

3 жыл бұрын

@@johnnycampbell3422 I understand, but how many viewers do you think they have a lathe (and the knowledge to operste it), a forge, a sanding machine lithe that, etc. And how many a peak (and the knowledge to work it). It is a great way,but not an easy one

@johnnycampbell3422

3 жыл бұрын

@@juanistella8469 I could buy the parts at ace hardware and build it with JB weld and a hammer, so, no need to good to fancy with a driving/ firing rod with a head weight and some rubber mat.

@juanistella8469

3 жыл бұрын

But then you would be changing the method. Still, this guy is not buying anything, he is building the tools for his method. Also, I asume (but I might be wrong) that you live in USA. Believe me when I tell you that getting some things is not that easy in many other places. I am from Argentina. Arround here, getting (legaly) a simple box of ammo is quite difficult. You don't get them without being registrated nor in any regular market... Anyway, I understand what you are saying, but, personaly, I still don't think it is an "easy" way. Thanks for your comments anyway.

@johnnycampbell3422

3 жыл бұрын

@@juanistella8469 correct you are. I don't know the access to blank cartridges in your area or even a piece of rebar or steel rod. Not to mention the portable drill and the bit. What is the easiest way you have moved (or could) such stones? Anyway, best regards to you from Texas.

Excellent 🖒

is great idea , i wanna try my backyard

We likes crazy people. BTW, go back and see how much flex you have in the table on that poor little drill press ya got. You need to put a small scissor jack under that thing for support.

How to break rock the easy way: spends all day making tool with other tools most people don't have

@gregoryhalye8907

3 жыл бұрын

Once you knuckleheads try breaking rock the HARD WAY for a few weeks, you will be very appreciative of anything that can do the job faster or easier...

@ThePsychodad69

3 жыл бұрын

@chris chris well if you never broke a rock, you probably play paintball with a controller.

@jonjudice1155

3 жыл бұрын

Exactly! You know how many rocks I could've broken with a sledge hammer in just the time frame of this video? Me either because I ain't trying to break rocks

@rrt5000

3 жыл бұрын

Most DIYers and hobbyists have some to most of these. I got everything except the furnace

@barbaracocart2164

3 жыл бұрын

Qzq

Jesteś mistrzem:)))

Good idea

Лëлик и Болик :))

Those power shells can drive a 22 pellet 4x faster than a standard 22 shell. Devistating impacts for flesh, and stone Amplify the effect by loading stone powder in the hole on top of the rod and shell. Like they do with anfo when used in blasting.

Great job 👍

Dude... when you start drilling the center hole you need to drill a center hole first to prevent wander since your center on that large barstock is not centered.

A little dangerous for me

@make_it

3 жыл бұрын

This is mikroexplosion and could be little dangerous and some knowledge and experience needed to do this, anyway not more dangerous than fireworks made by drunked people celebrating new year.

Excellent.

very clever ide👍

Everyone knows that paper beats rock. This was totally unnecessary.

Well, yeah. It's cool but an asian or hispanic dude would have had that large stone split nine ways to sunday by the time it took to manufacture this contraption. With a simple bunch of rebar pieces and a sledge. Nowhere near as dangerous as this could be in the wrong hands to boot.

@charlesbucholz8079

3 жыл бұрын

Shit, a privileged white boy, and inexperienced black guy would of split that rock nine ways to Sunday in that amount of time. The Hispanic and Asian would've had a sculpture of Elvis Presley carved out using just a file and toe nail clippers.

@Esuper1

3 жыл бұрын

@@charlesbucholz8079 The first two would smoke a big joint and pass out on top of the rock.The asian one would be like a dragon holding a huge pearl. the hispanic .... well yeah, maybe Elvis or El Chapo.

@charlesbucholz8079

3 жыл бұрын

@@Esuper1 Lol...and still had time to spare

@ElizabethGreene

2 жыл бұрын

Could they do it deep in a cave laying on their back with about two feet of clearance? That's the most common use for these.

Amazing!

Maravilha sensacional....

Если есть возможность притянуть перфоратор и подключить его в сеть,то нахуга этот весь цирк?

@ravembersnow5364

3 жыл бұрын

Как можно перфоратором так разломать камень?

@verba768

3 жыл бұрын

@@ravembersnow5364 легко и просто. Просто времени нужно чуть больше. Раз так в 100

Nothing easy about this.

@wolffang489

3 жыл бұрын

Pretty easy the second time.

So clever!

Awesome

9:20 a je to :) skvělá práce

Excellent job brother