HOW TO: 2017 CIVIC TYPE R FRONT STRUT REMOVAL! WATCH IF YOU NEED HELP!!!
Watch this video if you are having trouble taking off the front struts on a Civic Type R! I put together this short tutorial to help Civic TYPE R owners and shops on what parts to remove to get the front struts off the car. This will come in handy when you are upgrading to coilovers or upgrading your springs! FYI: This is not a complete DIY. I did the video while we were installing Eibach springs on my friend’s TYPE R. Removing the front struts on this car can be very tedious and confusing if you are not a seasoned technician. Honda definitely did not take any short cuts on engineering the front suspension assembly. On another note, the rears are very easy to work with. If this video helped you, like the video and subscribe for more! If you would like a complete DIY video, please comment below. I hope this helps and good luck!
Social Media:
Instagram - @fenderdefender
Пікірлер: 34
If you guys need any suspension related technical help, leave a comment below and I will do my best to make a video on it or give you a reply on the comment section on how to do it.
@threadoflife
2 жыл бұрын
I wish you’d show how to cut the bump stops and location in the video, can this be done after installing or while everything is installed or do they need to come out, for lowering spring installs?
Thanks for putting this together, well explained!
This awesome i did the rear install and had a shop do the front for me. I attempted but just decided to have someone do it first.
@FenderDefender
6 жыл бұрын
Jeremias Jabonero thank you!! I will have a full diy tutorial up soon.
@jeremiasjabonero482
6 жыл бұрын
Dope thanks man!!! You also do stuff for outcastgarage right in santa ana?
@FenderDefender
6 жыл бұрын
I used to have a shop right next to those guys!
Cool! Thanks for sharing! 👍🏻
@FenderDefender
6 жыл бұрын
Cathy L. Not a problem!
Hi, do you know if the process is the same for an fk2?
Thanks for sharing! Hay question how did you remove the sensor clip? I can't seem to remove mine.
@FenderDefender
6 жыл бұрын
Steve Tan Hi Steven which one are you referring to? Send me an email fenderdefenderoc@gmail.com and I can assist you through there.
I don't daily drive my type r and am lowering it on swift springs. do I need to cut the bump stops? I don't mind a harsher ride. what's the benefit? thanks
@threadoflife
2 жыл бұрын
You definitely need to cut them, I just installed my spoon springs and we didn’t cut them like the instruction say too and I’m bottoming out on any bumps, you want to take off 15mm from the front and rear.
How much force did you have to apply with the ball joint separating tool? I torqued mine down way past the point where all other ball joints broke free and it wouldn't pop free. I pretty much did as much as you did but also released the tie rod to get more movement of the knuckle assembly. Guess I'll pick up a beefier separating tool and try again. Also, did you remove locating bolt in the upper strut hat to allow movement for camber adjustment?
@FenderDefender
6 жыл бұрын
john bauer use a generous amount of force :). You will hear a very loud popping noise once it comes out.
@FenderDefender
6 жыл бұрын
No need to release the tie rod.
@FenderDefender
6 жыл бұрын
john bauer I didn't remove the locating bolt on this particular Type R.
Do you need a press to get the ball joint back in?
@FenderDefender
6 жыл бұрын
You don't need to use a press but it will make it easier.
What size of disposable nut do I need for the ballpoint? I’m trying to buy one online and currently on the project.
@FenderDefender
4 жыл бұрын
Koomoo Ly Hey how’s it going? I believe it’s M14x1.5
@PURE1945
4 жыл бұрын
Fender Defender I’m doing good, just order a nut and different ballpoint separator because I’m stuck lol
I like to see the full tutorial please
@FenderDefender
6 жыл бұрын
Kai Qian I will do a complete diy write up soon with pictures or a video once I do another spring installation on a Type R!
I’ve lowered my R w/Tein springs. Put Swift on 1st,but after installation,I was getting a knocking noise on the right side. Changed to Tein,& I’m still getting the noise. It doesn’t knock the whole time,but certain bumps I’ll hear it. Everything is tight,& done right. Any suggestions on what it could be?
@felixjuarez5625
3 жыл бұрын
Spring is not sitting rite ..
@threadoflife
2 жыл бұрын
Did you cut 15mm off of your front and rear bump stops if not that’s what it is?
@ronniemorgan5143
2 жыл бұрын
@@threadoflife. Yeah. Cut the bump stops. It ended up being the sway bar end link. We didn’t loosen the lower nut, it came loose from when we took the top nut off.
@threadoflife
2 жыл бұрын
@@ronniemorgan5143 nice I figured you’d of got it by now good deal! I’m about to have to redo mine because they did everything wrong! They didn’t cut my bump stops! 🤦♂️
what is size off "U opening" did you use?
@FenderDefender
5 жыл бұрын
alhussein hakim hi I will get the measurements in a few
hey where did you buy the splitter tool?
@FenderDefender
6 жыл бұрын
Robert M you can actually get that tool from autozone or your local Snap-On dealer