No video
2013 - 2017 Honda Accord Strut Mount or Strut Replacement, front end noise
Detail video of how to remove and replace a 2013, 2014, 2015, 2016 & 2017 Honda Accord Strut Mount or Strut Replacement. Front end noise, passenger right side noise or driver left side noise. Rattling sound in front of 2013 - 2017 Honda Accord Strut Mount or Strut Replacement, front end noise
Пікірлер: 37
Perfect video,thanks 👌 👍
I'm changing my by morning. Thank you so much. This video was enlightening
@whypaydiy
8 ай бұрын
Your welcome
Explain everything very well 👍 more vids like this
@whypaydiy
Жыл бұрын
Thank you
Great tutorial!
thanks the best video so far even though you didn't change the strut but is exactly the same thing lol 😂
Thanks for the 411, brother!
@whypaydiy
Жыл бұрын
No problem
thank you for this post, my dude. very helpful. 💯
@whypaydiy
3 ай бұрын
Your welcome
Nice vedio but putting a vice grip on the strut pole is a very bad idea, if you as much as scratch the pole it will cause the seal to leak and secondly, if the strut pole is sliding down inside you pushing up you have a damaged strut. Quick tip. A bent strut pole will damage the mount.
@whypaydiy
Жыл бұрын
You are right and that's why I did not move it at all or spin it, it was just to hold it.
You make me a little nervous sliding your feet under the car when you only have it up with a floor jack. Never get any of your body bits under a car if it's only supported by a jack and not jack stands...
@whypaydiy
Жыл бұрын
That's true, i have 4 jack stands and I was just lazy and said it would be quick. It is always best to use jack stand with jacks.
Don't touch shock shaft with pliers
How did you get the bolt for the strut mount not to spin?
@whypaydiy
5 ай бұрын
Have to use an impach wrench
What’s the tool used to pop the tie rod end out?
@whypaydiy
2 ай бұрын
Ball joint removal tool, get it on amazon cheap like $20
To do this job properly you have to take the lower ball joint out and separate it from the knuckle and take the axle out of the knuckle. Remove the knuckle from the strut and the strut will come right out . This is not a job you should do on the street. You see he doesn’t show how he got the strut and knuckle lined back up. It was probably him and two other people.😂😂😂
@Yoman6767
Ай бұрын
I tried doing it his way and you are right. I had to ask my friend for help and we STILL struggled with 2 people to get the strut back into the knuckle. I will try your way now for the other side. Thank you 7951!
is it difficult to pop the cv axle back in?
@whypaydiy
Жыл бұрын
No, it is not. It's a tripod bearing that slides in a slot.
@ackeemsmith2076
Жыл бұрын
I wish you showed that part a little more but ty
@whypaydiy
Жыл бұрын
@ackeem Smith it did not come out on the booth. So it is show in the vid. Just don't remove the both and you good
Yang sebelah kiri bagaimana cara bukanya,apa sama seperti sebelah kanan Mr mekanik
@KEYTECHNIQUES
5 ай бұрын
It’s same procedure.
How'd you get it back in?
@whypaydiy
6 ай бұрын
Its in the video
What model/torque is that Rigid?
@whypaydiy
3 ай бұрын
Model # R86212B-AC87004
Hope you bleed the brakes after doing this. Because taking the banjo boat off. You let a lot of air in the system.
Ha. Rookie
Dang good video!
@whypaydiy
11 ай бұрын
Thank you