Do not do what he did with the wire wheel. Just use a razor blade that was hard to watch.

@MobileCarMechanic

Жыл бұрын

A razor blade works perfectly fine as well. Cheers!

@Sedatyunus

Жыл бұрын

Hahaha definitely.. he is a wire killer lol

@Tkjawa

Жыл бұрын

I couldn’t believe my eyes when he used a wire brush with a power drill. This is next level stupid

@KainHerringCorey

11 ай бұрын

💯 agreed! I was looking 👀 like 😬

@10thgensiracing

8 ай бұрын

I was hoping there wasn’t marring or scratches. Luckily there wasn’t any. That was insane to use a power drill just to remove the silicone that could have made it worse.

Thank You Sir ! One tip, please do not flip the dirty valve cover on top of the open engine. You may drop debris in the engine as you can see it in the video at 11:01 to 11:05. Very helpful video.

@MobileCarMechanic

Жыл бұрын

Thank you for the advice and the comment. Cheers!

Thank you I was able to replace my car’s valve cover gasket with no problems. I appreciated the simple detailed explanation and camera angles they were extremely helpful and instrumental for me. You are appreciated.

@MobileCarMechanic

6 ай бұрын

You're welcome!

@chriswincek8672

4 ай бұрын

About how long did it take you? Do you need to let the RTV set for a certain amount of time before driving?

Why is this channel so underrated? You deserve more subscribers and views.

@MobileCarMechanic

Жыл бұрын

Thank you for the support.

Thank you! Your video with the addition of all the comments helped me change my valve cover gasket yesterday. No leaks after a drive, but I did trip the check engine light which also lit up the traction light, tire pressure light, and power steering light because I forgot to plug in a connecter. Rewatching the video solved that problem. Just need an OBD2 to clear the codes now

@MobileCarMechanic

Жыл бұрын

Glad our video helped. You can usually goto an auto parts store and use their scan tool for free. Otherwise just disconnect the battery for a couple seconds and reconnect. That usually resets the computer.

@lemon4400

Жыл бұрын

@@MobileCarMechanicthank you again boss! disconnecting the battery worked to clear the lights ❤

Appreciate the step-by-step visuals, easy to follow and makes an intimidating (though easy in actuality) repair something I felt good about tackling. Some videos skip showing certain steps and makes it seem like the repair magically does itself. The fact that this video shows things like tools dropping was informative because it taught me there are certain parts of the repair prone to errors happening. Forewarned is forearmed, thanks coach!

@MobileCarMechanic

2 ай бұрын

Glad the video was helpful and thank you for the kind words. Cheers!

Excellent video with easy to follow step by step instructions. I followed along and was able to make the replacement on my accord myself - saving me a couple hundred dollars! Thanks!

@MobileCarMechanic

Жыл бұрын

Glad the video helped.

@TheFishingfoolr

7 ай бұрын

I did the same, it was a awesome video👍

Great work! I love the details and steps taken to show the old and new replacement.

@MobileCarMechanic

2 жыл бұрын

Thank you, Glad the video was helpful!

Great video, gets the major bases to the point that anyone with a little aptitude should be able to handle this job. I'd also recommend a small extendable mechanics mirror, you can see if the gasket is indeed seated on the backside because as you showed....it's a bugger keeping it in the valve cover. Thanks again for diving in and sharing your experience.

@MobileCarMechanic

5 ай бұрын

Thank you for the kind words, A mirror definitely would help with the rear portion of the valve cover. Cheers!

Good work brother! Thanks for sharing. It seems fairly simple.

@MobileCarMechanic

Жыл бұрын

You bet. Thank you!

Respectfully, using wire wheel allowed tons of debris to enter the engine. Razor blaze or sandpaper, scrubbing outward would of been a better option. Other than that, great video and definitely a subscriber!

@MobileCarMechanic

Жыл бұрын

Thanks for the sub and comment. Definitely should have thought that one through but I did make sure to inspect for debris to ensure nothing was there off camera. Would advise a blade. Thanks again and Cheers!

Excellent and very detailed video. Thank you! This is how you make a video. I am subscribed! Look forward to more of your videos.

@MobileCarMechanic

Жыл бұрын

I appreciate your kind words. Will continue to make detailed video. Thank you!

Incredibly helpful video. Thank you sir!

@MobileCarMechanic

Жыл бұрын

Glad to help. Thank you!

Thank you for this great video. This video gave me the confidence to do the job myself. Job done ✅

@MobileCarMechanic

7 ай бұрын

Glad I could help

That was outstanding. Well done. Thanks

@MobileCarMechanic

Жыл бұрын

Thank you!

3 recommendations 1 is putting rtv on the gasket and cover before putting it on to secure it into place, not alot, just a light application 2 is USE A GASKET SKRAPER! No need to nick any aluminum 3 always be sure that you don't spray into the head, just apply enough to a old rag to clean the mating surface of the head to gasket.

@MobileCarMechanic

8 ай бұрын

Thank you for your recommendations. Cheers!

Excellent Video.. detailed and accurate. Thanks.

@MobileCarMechanic

Жыл бұрын

Thank you. Cheers!

Excelente trabajo! Gracias por compartir experiencia.

@MobileCarMechanic

Жыл бұрын

Me alegro de que haya ayudado. Gracias.

Thanks I have honda accord 2017 an is leaking with your help a do it myself. I appreciate 🙏

@MobileCarMechanic

Жыл бұрын

Thank you!

Great video and great editing.

@MobileCarMechanic

7 ай бұрын

Thank you!

I'm liking your slow paced videos. Very helpful. Can you do one on a intake valve cleaning since they get mucked up with the GDI design? I have a 2014 Accord.

@MobileCarMechanic

2 жыл бұрын

I’m not sure when I will be able to create a video. But will keep you posted when we do. How many miles do you have on your accord?

@MrSpandya22

2 жыл бұрын

@@MobileCarMechanic 103K

Excelente, el mejor que vi fue el tuyo, gracias

@MobileCarMechanic

8 ай бұрын

Thank you.

You’re a master! Thank you so much!

@MobileCarMechanic

4 ай бұрын

You're welcome!

I like your videos they are very easy to follow. Can you do a replacement of struts for 2014 Honda Accord ? That would be very helpful.

@MobileCarMechanic

2 жыл бұрын

At the moment I don't have a 2014 Honda Accord that I could work on. Maybe in the near future. Be on the lookout for the video. Thank you for your feedback.

Ran to the comments as soon as I seen the drill 😂

@MobileCarMechanic

7 ай бұрын

The drill will not be making an appearance lol. Cheers!

I have a 2014 Honda Accord EX-L. I will be doing this very soon. I noticed mine was leaking a few days ago.

@MobileCarMechanic

10 ай бұрын

Follow our video and you will be golden!

Great video. My one tip that I didn't see anyone else say is when you're breaking loose all 10 valve cover bolts just go around and do it, then take extension and finish them all by hand instead of taking the extension off & on the ratchet 10 times. Something iv learned over the yrs to save time without compromising quality of work

@MobileCarMechanic

Жыл бұрын

Thanks for the tip! It’s a tedious take removing the bolts and anything to speed it up helps out. Thanks for the comment. Cheers!

Thank You for the Video! Great breakdown! Where did you get your strut bar?

@MobileCarMechanic

11 ай бұрын

The strut bar is stock and came with the car. Not sure if this applies to the sport. What model do you have?

Thanks for putting this together. I just did the valve cover gasket (along with the seals and grommets) on my 2004 Honda Accord. This is probably the same difficulty, but in a different way than the 2004 Honda. With the 04, I pulled the power steering hose away from the power steering unit since it went over the corner of the cover. I don't see that issue here. But for this generation, there's a LOT more electrical connections to disconnect (but at least the power steering hose isn't an issue). Is there a reason you didn't do the grommets and seals while you had it off? One criticism would be cleaning parts sitting inside the car. You could have easily gotten brake fluid/cleaner on your paint. Far better (in my opinion) to put things on the ground, away fro the car, to clean them. Think I'll pull the negative battery connection as well to be on the safe side. All in all, nice work!

@MobileCarMechanic

Жыл бұрын

Thanks for the input. So the valve covers on this year have the spark plug tube seals integrated in them and only way to replace them would be replacing the whole valve cover itself. No leaks in the tubes. Thanks again for the comment. Always striving to do better. Cheers!

@MobileCarMechanic

Жыл бұрын

The generation varies. Multiple years and variations. Not sure if multiple manufactures. Went to Honda and provided vin which indicated the model owned didn’t have replaceable tube seals. I have a 2000 civic and know those seals need to be replaced

Pieces of debris went in to the engine, covering the entire area is a must bro.

@MobileCarMechanic

2 жыл бұрын

Will do. Thanks!

@johnjobber2219

Жыл бұрын

@X XL Give him a break he is just an amateur

Great instructional video, what were your torque specs for the valve cover?

@MobileCarMechanic

Жыл бұрын

7 N-m or 5 lbf-ft

Very nice instructional video. Can you do one on how to replace an alternator on Hondas?

@MobileCarMechanic

Жыл бұрын

Yes, soon. Great suggestion.

@MobileCarMechanic

Жыл бұрын

Here it is: kzread.info/dash/bejne/oaGay9JtYMafcbg.html

@laviebanale

Жыл бұрын

@@MobileCarMechanic I just finished doing the valve cover gasket on my Honda. The video was abt 90% the same bc my car is a CRV. The video helped a lot. 🤝

@gameemulator2448

10 ай бұрын

​@laviebanale did you change your spark plug seals also?

@laviebanale

10 ай бұрын

@@gameemulator2448 I actually didn’t bc they were in good condition but to be safe I really should have.

I would do the wire brush and drill, also spray the shop towel with the brake parts cleaner not the valves. Before all of this use a leaf blower and brush off any stubborn deberes, also are the bolts aluminum and need to be replaced? other wise great video.

@MobileCarMechanic

8 ай бұрын

Thanks for the tip. The bolts aren’t aluminum and don’t need to be replaced. You can reuse the bolts. Cheers!

Great video and it is gonna help me to change mine this weekend, but I have a question. Do I need to drain the oil from my engine? I just change the oil 2 weeks ago, thank u in advance and You just gain a new subscriber,, thank U

@MobileCarMechanic

2 жыл бұрын

Thanks for Subscribing! You don’t need to change your oil. Just make sure you don’t get any dirt while your replacing the gasket and you’ll be fine. If you do manage to get dirt in there I’d recommend cleaning that up and probably doing another oil change.

@culionfilo

2 жыл бұрын

@@MobileCarMechanic thank u

Going to try at replacement, trying to find out where the leak is coming from first. It looks super easy especially for a woman trying for the first time

@MobileCarMechanic

Ай бұрын

Where have you noticed the leak? A good way to try to find leaks is to use an engine degreaser to clean all the dirt and grease off and then drive it for a couple days to see if you any new oil stains which may help you find where it’s coming from. You got this! Cheers!

hey thanks for the video! One thing I noticed is that you had oil in spark plug tube, which would indicate a bad seal on that tube but you didn't replace anything on that. Those gaskets are not removable?

@MobileCarMechanic

Жыл бұрын

The seals are built into the valve cover. I thought it was replaceable but unfortunately not. I had done the gasket before but didn’t realize at the time the spark plug seal had inverted itself causing it not to seal. When I did the video I put it back as it should which fixed the leaking issue.

Make sure you buy gasket from dealer,the dealer gasket,is a little,thicker Than the auto store gasket

@MobileCarMechanic

Жыл бұрын

Thanks for the tip, we bought it from rockauto since it included spark plug tube seals which we didn’t end up needing them since they were built into the valve cover

@seraphim3TN

Жыл бұрын

always use OEM parts when working on a Honda.

Nice and shiny

@MobileCarMechanic

2 жыл бұрын

Thanks!

Any tips to remove the bolts on the beauty cover (where it says Earth Dreams) if they just keep spinning and doesn't come out? Have one bolt with that issue

@MobileCarMechanic

2 жыл бұрын

I’d try to lift up the cover while removing the nut to apply resistance to the stud that’s spinning to see if it comes off

@marcussiew3019

2 жыл бұрын

Same any update on how you got it out?

@lji2000

2 жыл бұрын

@@MobileCarMechanic Tried this, no luck. What's amazing is that the PCV bolt on the valve cover is doing the same thing.

Bro: What are the torque specifications for the perimeter bolts for the valve cover gasket? I would use plastic razor blades to remove the RTV because the aluminum surfaces scratch easy. Place a towel over the entire timing chain bay so that U dont drop a screw, bolt into the timing chain bay. The Honda dealer in LA charges $1600 bucks for this job. Thanks for sharing knowledge.

Thank you for the effort. Do you happened to know what is the purpose of the little squarish grommet gasket on the inner middle of the cover? It looks like it communicates with a port going down the block and it has an evacuation channel in the cover. Is this the EGR re-circulation channel?

@MobileCarMechanic

5 ай бұрын

Not sure to be honest, I know the red piece is integrated into the cover which I believe is the PCV valve, the cover on the right side of the engine covers the high pressure fuel pump. I don’t see the squarish grommet in the middle that you are talking about.

@MrLevi136

5 ай бұрын

Thank you for responding. At 15:40 the small squarish gasket can be seen on the valve cover close to cyl 2-3. There is another evacuation port at 11:25 going toward the high pressure fiul pump one toward the main air duct and one back to the intake manifold. Im trying to understand how this valve cover integrated PCV system works. From which port and in what direction vapors and fresh air is moving? This 2.4l engine has no EGR valve at all?

Do you recommend to put RTV to the gasket to keep in place ?

@MobileCarMechanic

2 жыл бұрын

It won’t hurt but it’s not required and will make more of a mess

Very clear and helpful but one thing ? Didn’t show when you tighten the cover bolts and how much torque,,, thank you so much.

@MobileCarMechanic

6 ай бұрын

Thank You, The torque specs for the valve cover are 7 N·m or 5 lbf·ft

I have a 2017 accord sport at 118k miles, should i consider replacing it even though i don’t see oil leak?

@MobileCarMechanic

Жыл бұрын

If you don’t see a leak I would wait until you do before replacing.

Hi great video, I followed the video instructions and when I was done there were no warning lights on my dash and a few hours later when I turned my car all the lights went on … please help

@MobileCarMechanic

10 ай бұрын

It would be a good idea to double check your connections, but I would advise to get the code read to give you a direction to the problem. Cheers!

Hello Mobile car Mechanic, I have a honda 2014 accord V6 engine. I noticed a transmission leak & my mechanic says its from the seal in the transmission , does he need to bring down the transmission to fix the seal

@MobileCarMechanic

2 жыл бұрын

Is it the seal between the transmission and engine commonly referred as the rear main seal? If yes then transmission has to be removed to replace. If it’s axle seals then no

My car needs that gasket, but what’s the difference if I don’t put/use Black adhesive sealant?? & Brake Cleaner doesn’t affect the Engine?? Thank you

@MobileCarMechanic

8 ай бұрын

The sealant is needed for the gaps on the cylinder head where the timing cover is. The gasket won’t seal it as well if you don’t apply it.

This helped me out and gave me the confidence to do it myself. Until I snapped a bolt off in the engine 😢

@MobileCarMechanic

4 ай бұрын

Where did you snap the bolt?

Thanks

@MobileCarMechanic

9 ай бұрын

Glad our video helped. Cheers!

I got a P0304 check engine light after I replaced mines, any idea why?

@MobileCarMechanic

Жыл бұрын

Unplug and plug cylinder 4 ignition coil. Either plug is loose connecting to coil or the coil is bad. Also check to see if oil is in the spark plug tube.

How did you remove the oil from the 3rd spark plug? Didn’t see that.

@MobileCarMechanic

Жыл бұрын

I took out the spark plugs off camera and put a paper towel over the tube and cranked the engine to blow the oil out. Did that multiple times while holding the gas pedal down to the floor to prevent fuel from being injected.

@israelgomez8373

Жыл бұрын

Thank you

Can you do a video replacing the fuel injectors on the same car

@MobileCarMechanic

Жыл бұрын

If by chance I get an accord of this gen for sure.

Wen one of the spark plug seals leaked was it instantly wen u seen the leak ?

@MobileCarMechanic

Жыл бұрын

I didn’t see it right away. I replaced the valve cover gasket as it was leaking. It was then I saw the spark plug seal was not sealing as it had collapsed for some reason. I adjusted it and it’s been good so far. It’s not replaceable on this year as it’s built in to the valve cover. So far so good. A spark plug tube seal was only leaking on one cylinder. Since it wasn’t sealing I took out the spark plugs and pulled the fuse for the fuel pump so that I could crank the engine to blow out the oil. Had a paper towel over the tubes so it wouldn’t spray everywhere

So somehow one of the bolts holding down the earth dream cover that covers the coils, is stripped and I can’t get the bolt out now. It just keeps turning and turning. Any advice on how to get the bolt out?

@MobileCarMechanic

Жыл бұрын

Honestly I haven’t had that happen with this car. But you can try lifting the cover to apply tension to the bolt to see if it helps. Otherwise we may need to somehow heat up the nut without melting the cover or breaking the cover off and extracting it after. If it’s spinning the recessed thread that holds it in place is moving and maybe you can try to lift up on the nut somehow to pop it out the recessed thread.

@jmc224

Жыл бұрын

@@MobileCarMechanic thanks boss! I was able to get the coils out to get this project done. But in the process of putting everything back together, the plastic cover broke. Lol. I’m gonna try to get the bolt removed like you suggested and order another earth dream cover via eBay.

Use razor blade to get rid off remaining residue. And clean the calve cover in a different area. With a wet coil meaning the gasket where the coil sits needs to be replaced. Other than that you did awesome. Two thumbs up

@MobileCarMechanic

Жыл бұрын

Thanks for the comment. We couldn’t replace the spark plug seals as they are integrated into the valve cover. You will need to replace the valve cover to replace the seals.

@jaydenimpton6798

10 ай бұрын

use a plastic blade though. Metal razor blades can gouge the mating surface and oil will find its way out!

Question if you see this. I have 2015. The dealer told me you can’t change the tube seals for the spark plugs? Is that true? I didn’t see you change them on camera at least so I’m just wondering. Thanks

@MobileCarMechanic

Жыл бұрын

They are correct! It’s integrated to the valve cover which is why we didn’t change it either

@Zebraunit22

4 ай бұрын

What did you do about the oil in the spark plug tube

How many miles did your car have ? Im at 170K and i seen some oil seeping thru but not enough to drip to the ground.

@MobileCarMechanic

Жыл бұрын

I believe around 120-130k is when we did this as we saw seeping but wasn’t too bad.

How come you didnt use a blade to clean the surface off the valve cover and and then use a light sandpaper also you should apply a little of silcon on the gasket so it doesnt come off .Anyway great video 5 star

@MobileCarMechanic

Жыл бұрын

The valve cover didn’t have any silicone on it, just the mating surface on the cylinder head. Applying silicone would have made it easier to make the gasket stay in place but it wasn’t necessary. Thanks for the comment! Cheers

I was charged 350 for this bs easy task while I was away & had my mom bring it to the dealer 350!🥶

@MobileCarMechanic

5 ай бұрын

Yep, it's not a tough job. Dealers love to overcharge you.

How long we can drive after replacing the valve gasket?

@MobileCarMechanic

Жыл бұрын

I’d advise waiting an hour or 2.

Anyone know what the torque specs are for the valve cover bolts?

@MobileCarMechanic

Жыл бұрын

7-Nm 5 ft lbs

Dremel with a wire wheel would be more surgical but I'd still be afraid of getting debris into the engine.

@MobileCarMechanic

Жыл бұрын

You will need to be careful. Made sure no debris was in there off camera. A razor blade will suffice

Just did this, valve cover should come off pretty easily, there is also a bolt under the plastic heat shield, my rubber grommet got stuck to it and I couldn’t find it

@MobileCarMechanic

6 ай бұрын

Did the grommet not get stuck to the plastic shield?

After I finished my power steering light, traction control , and tire pressure light was on. Does anyone know what it could be?

@MobileCarMechanic

Жыл бұрын

Double check and review the video for the connections that were disconnected.

@embggotty708

Жыл бұрын

@@MobileCarMechanic Thank you I missed a connector, I’m gonna drive it to see if the lights go off.

I did everything except that @9:09 clip wont come off. I spent 2 hrs figuring out how to get those out. I gave up. Any tips on that??

@MobileCarMechanic

Ай бұрын

You can still remove the valve cover but make sure to turn it towards the firewall/windshield and then you can access the wings on the clip to pinch them and remove it.

Is there a rear and front gasket?

@MobileCarMechanic

7 ай бұрын

Only if you have the V6 accord.

You didn’t disconnect the throttle body connector did you?

@MobileCarMechanic

Жыл бұрын

I did not. If you only disconnect what’s on the video that is all you will need to free the harness and give you that space to remove the valve cover without obstructions.

@javonturner1506

Жыл бұрын

@@MobileCarMechanic great advice ! appreciate the fast reply also !!

Bro the gasket cover seal keeps falling off. Almost feels like its to big but it fits perfect

@MobileCarMechanic

8 ай бұрын

Yes it does

Why not replace spark plug hole seals too?

@MobileCarMechanic

2 жыл бұрын

Because on this year (2016) they integrated them into the valve cover. Have to replace the valve cover to replace those seals

@fsal9990

Жыл бұрын

Do you happen to know if it’s the same for a 2017 Honda Accord Sport ?

@kevinkkh01

Жыл бұрын

what about that square gasket in the middle for pcv? why not replace that one too?

I did this and now I have a P0420 code for the cat converter

@MobileCarMechanic

Жыл бұрын

I’d double check that all wires are connected as well as hoses. How many miles are on your car?

@Dave-tr2ru

Жыл бұрын

@@MobileCarMechanic 100k

Hey, I got a P0507 code after this, did anybody else get this? Everything is reconnected. The light comes and goes.

@MobileCarMechanic

11 ай бұрын

Try this procedure to relearn idle values after you have double checked connections. You will need to clear the light with either a scan tool or disconnect the battery for 30 seconds. You do not need an HDS which is a higher end scan tool. May need to repeat procedure multiple times. imgur.com/a/puckNYl

Good video all in all. But lost me at the wire wheel.

@MobileCarMechanic

Жыл бұрын

Thanks for the comment. We did make sure to check the engine for debris and cleaned. Using a razor blade would be advised

Is this a 2.4 liter engine?

@MobileCarMechanic

8 ай бұрын

Yes

Followed this video, now all my check lights are on, how to fix?

@MobileCarMechanic

Жыл бұрын

I would double check to see if you didn’t leave any wires disconnected. If you have a code reader it may help direct you where you need to look. Also make sure there isn’t any oil where the spark plug tubes are.

@MrBMWF30

Жыл бұрын

@@MobileCarMechanic for f sake, its 1 wire forgot to connect.... Cheers

@MobileCarMechanic

Жыл бұрын

It happens to the best of us. Glad it was an easy fix. Cheers!

Why did someone say you need to adjust something prior to completing the job?

@MobileCarMechanic

Жыл бұрын

Can’t remember honestly.

Homie said you don’t need to change the o rings. Yet one was full of oil lol

@MobileCarMechanic

Жыл бұрын

The spark plug tube seals are built into the valve cover. Realized that one of them collapsed. When I put it back in its position the oil stopped leaking into the spark plug tubes. Cleaned it off camera. All is good now. Cheers!

Spray brake cleaner right into an engine!?! Wire wheel to remove old dried silicone? Wouldn't want you working on any vehicle i own! Won't mention the simple trick everyone seems to know but you on how to keep a rubber gasket in place.

@MobileCarMechanic

9 ай бұрын

Thanks for your feedback. Cheers!

Can you start the car right away. Or are you really supposed to wait 3 hrs?? Because I got things to do and places to be after the replacement lmao! FR

@MobileCarMechanic

3 ай бұрын

It’s recommended that you wait otherwise it’s going to leak as it won’t dry in time and then the oil will contaminate it and make it not cure. So do this when you have free time or have another vehicle.

Watching the old RTV fly all over the exposed valve train with the drill stressed me out. I've found a fresh razor blade is sufficient.

@MobileCarMechanic

Жыл бұрын

Razor blades are sufficient. Made sure to clean everything off camera. Thanks for the comment!

Do you have the sniffles young man ?

@MobileCarMechanic

2 ай бұрын

Haha no sniffles. Car work gets me going.

How long would this take

@MobileCarMechanic

7 ай бұрын

This took me 30-45 min

It's a shame that Honda ended up doing what everyone else. Saving money by putting plastic valve covers, that's the reason why they leak.

@MobileCarMechanic

6 ай бұрын

It’s a bummer but honestly it leaks the same way as any valve cover gasket, just sucks they integrated the PCV into the valve cover! Even my civic with a metal cover leaks after sometime with a rubber valve cover gasket. Rubber degrades overtime!

So the dealership and went through basically tighten every damnable in that damn car to the point where I need a breaker bar on every bolt the stupid little plastic piece on top I had to rip off then take off the bolts because I was afraid I was going to rip some shit off my damn oil drain plug plus so fucking impacted on I had to leave it take my impact and work with it oil filter dude was so packed on there that it took me and my dad and the cousin to basically move this bitch out the way and we just said fuck it in stamp the oil filter with a screwdriver put a handle on there then putting extension handle on there than just every one of us has grabbed onto just pulled it off and the car has not been turned on for almost 3-4 hours

@MobileCarMechanic

10 ай бұрын

Sorry to hear that. I’d be super annoyed. I feel your pain. Lots have words have been said off camera for some of the dumb things I’ve experienced when fixing things on cars. Hopefully it will be easier next time. Cheers!

All kinds of stuff entered the engine. Drill not necessary, and more work than it should be. Plastic scraper is all that’s needed. And the spark plug gaskets just pull out with a screw driver and pliers. 🤦🏼‍♂️

@MobileCarMechanic

Жыл бұрын

Yes you can use a plastic scraper. Made sure nothing had entered. Some models of this generation accord have integrated spark plug tube seals in which this one did. I ordered the kit with the seals and unfortunately couldn’t replace them. Even verified via VIN at the parts desk at Honda which stated that it was not replaceable.

This kind of stuff drives me nuts. Using a wire brush with wire pieces breaking off and flying into the engine. OMG

@MobileCarMechanic

Жыл бұрын

I definitely should have used a razor blade but did check to make sure nothing was in the oil and head off camera.

Probably the gasket used is made in China, my 2012 Camry still have no leak until now.

@MobileCarMechanic

4 ай бұрын

We did use an aftermarket one before the original, definitely failed fast. How many miles are on your Camry?

@rodrigocastillo9231

4 ай бұрын

180K miles@@MobileCarMechanic

I was with you until you used the wire wheel

@MobileCarMechanic

8 ай бұрын

Thanks!

Fckn guy doesn’t mention that when you try to remove the cover…there is a 10mm deep socket that is needed to remove it. So make sure you h e that piece ready or you’ll waste your day going back and forth trying to purchase parts

@MobileCarMechanic

Жыл бұрын

We will make note to be a bit more specific in our future videos. Cheers!

Gave me a heart attack with those wire wheels. Don’t do that please. Also spray the cloth then wipe not directly to the mating surface. Goodness!!

@MobileCarMechanic

10 ай бұрын

Thanks for the feedback. Wire wheel won’t be making anymore entrances.

Lose the wire wheel and drill motor.

@MobileCarMechanic

6 ай бұрын

Thanks for the feedback. Cheers!

@robertmceuen3630

6 ай бұрын

@@MobileCarMechanic you're welcome. Helpful video. I learned from it.

Amateur home mechanic giving lack luster advices.... 😑

@MobileCarMechanic

Жыл бұрын

Thank you for the feedback.

@lemon4400

Жыл бұрын

The combination of the video and all the comments are making it easy to follow and learning how to do this job. Even though it’s amateur, it’s a really good tutorial video and resource.

WHAT THE FUCK ARE YOU DOING !!!!!!!!!!!!! DO NOT TOUCH THE CAR AGAIN !!!!!!!!!!!!!!!!!!!!!

@MobileCarMechanic

4 ай бұрын

Thank you for your feedback. Cheers!

Break cleaner?

@MobileCarMechanic

9 ай бұрын

amzn.to/46ERiNE