MY INSTAGRAM @anthonypilpa WHERE ALL MY DECALS ARE FROM untoldlove.us/ LINK TO CLUTCH DELAY VALVE DELETE untoldlove.us/collections/all...
Жүктеу.....
Пікірлер: 26
@NvSrAgE6792 жыл бұрын
Thanks so much for this. I’m doing mine in the spring.
@JustHavingFun_2 жыл бұрын
That R is clean!! Great job in the install.
@MilkzzpoT2 жыл бұрын
thats the spoon method! GJ! ive done around 5-6 installs doing it that method
@mickydrake12782 жыл бұрын
I have put lowering springs on my old Lancer and my old veloster N.wtf with that front suspension lol. I think I'm just going to get it installed
@bradgreen92252 жыл бұрын
like to do lowering springs on mine but im aftermarket 20's so not sure i would rub or not
@ivanc92326 ай бұрын
Make a video on how to pop the axel back on please
@alexiparis32442 жыл бұрын
Cool video, does this affect the different drive modes? Does it ride stiffer through all three modes?
@anthonypilpa7586
2 жыл бұрын
Yea it will feel different since I believe the spring rate is higher than oem
@civicracecar5152 жыл бұрын
Cool 😎
@kitsune387210 ай бұрын
It's the same on an fk7, isn't it?
@lichaoduan6499 Жыл бұрын
Nice video Anthony! I have a question here. I recently noticed a clunk noise from front suspension(especially noticeable when going over uneven surface). I took the wheel off and found height sensor link is kinda loose. Is that normal? I checked the end links, those are tight, not sure what caused the clunk.
@gamertyper6476
7 ай бұрын
ayo same here - I aint took it off and looked but mine is clunking too just installed swifts already put 100 miles on em still does it and legit only on uneven surfaces too, so it sounds like we have the same issue, did you ever figure it out man?
@lichaoduan6499
7 ай бұрын
@@gamertyper6476 unfortunately, nope. Just ended up turning radio up and loud lol
@raidersperez12782 жыл бұрын
Do I need any rear camber arms ? I only drive on weekends to another city to see family and it’s an hour to go and come back. I’m looking to drop only an inch.
@anthonypilpa7586
2 жыл бұрын
It all kinda depends on your wheel of set
@raidersperez1278
2 жыл бұрын
@@anthonypilpa7586 I went with the safe Spec from your other video. Enkei TS-5 18/9.5 +45 offset with 265/35/18 tires. I also commented in that video and If you replied to it I apologize.
@code_fk88172 жыл бұрын
Messaged you on FB yesterday lol
@gamertyper64767 ай бұрын
yo i get this clunking around noise when going over uneven surfaces with mine, anyone got any ideas?
@XOX-fs4ww
6 ай бұрын
U didn't put it back together right
@JayycobVNM Жыл бұрын
So it’s not necessary to cut the bump stops ?
@codychallenger0666
Жыл бұрын
Yea it is... or it's bad.. he just don't daily his so can't tell. .. If u don't it'll be more bouncy
@JayycobVNM
Жыл бұрын
@@codychallenger0666 I installed them and it seems like they are bouncy so I will have to cut those fuckers off 🥹 but it’s crazy that a lot people say not to cut them off smh
@wrenchbrosmotorsports3652 жыл бұрын
If you loosen the top three nuts you wouldn’t have had to fight the strut to pop out nor loosen that bottom compliance bearing 🤷🏽♂️
@Khaabkid2 жыл бұрын
Most complicated springs replacement
@MrJjburgess11
2 жыл бұрын
It's similar to how the VWs are . Kind of a pain compared to alot of other cars . But the rear being so easy. Makes up for it .
Пікірлер: 26
Thanks so much for this. I’m doing mine in the spring.
That R is clean!! Great job in the install.
thats the spoon method! GJ! ive done around 5-6 installs doing it that method
I have put lowering springs on my old Lancer and my old veloster N.wtf with that front suspension lol. I think I'm just going to get it installed
like to do lowering springs on mine but im aftermarket 20's so not sure i would rub or not
Make a video on how to pop the axel back on please
Cool video, does this affect the different drive modes? Does it ride stiffer through all three modes?
@anthonypilpa7586
2 жыл бұрын
Yea it will feel different since I believe the spring rate is higher than oem
Cool 😎
It's the same on an fk7, isn't it?
Nice video Anthony! I have a question here. I recently noticed a clunk noise from front suspension(especially noticeable when going over uneven surface). I took the wheel off and found height sensor link is kinda loose. Is that normal? I checked the end links, those are tight, not sure what caused the clunk.
@gamertyper6476
7 ай бұрын
ayo same here - I aint took it off and looked but mine is clunking too just installed swifts already put 100 miles on em still does it and legit only on uneven surfaces too, so it sounds like we have the same issue, did you ever figure it out man?
@lichaoduan6499
7 ай бұрын
@@gamertyper6476 unfortunately, nope. Just ended up turning radio up and loud lol
Do I need any rear camber arms ? I only drive on weekends to another city to see family and it’s an hour to go and come back. I’m looking to drop only an inch.
@anthonypilpa7586
2 жыл бұрын
It all kinda depends on your wheel of set
@raidersperez1278
2 жыл бұрын
@@anthonypilpa7586 I went with the safe Spec from your other video. Enkei TS-5 18/9.5 +45 offset with 265/35/18 tires. I also commented in that video and If you replied to it I apologize.
Messaged you on FB yesterday lol
yo i get this clunking around noise when going over uneven surfaces with mine, anyone got any ideas?
@XOX-fs4ww
6 ай бұрын
U didn't put it back together right
So it’s not necessary to cut the bump stops ?
@codychallenger0666
Жыл бұрын
Yea it is... or it's bad.. he just don't daily his so can't tell. .. If u don't it'll be more bouncy
@JayycobVNM
Жыл бұрын
@@codychallenger0666 I installed them and it seems like they are bouncy so I will have to cut those fuckers off 🥹 but it’s crazy that a lot people say not to cut them off smh
If you loosen the top three nuts you wouldn’t have had to fight the strut to pop out nor loosen that bottom compliance bearing 🤷🏽♂️
Most complicated springs replacement
@MrJjburgess11
2 жыл бұрын
It's similar to how the VWs are . Kind of a pain compared to alot of other cars . But the rear being so easy. Makes up for it .