How to replace the rear axle seal in a 2015 Chevrolet Silverado 1500
Жүктеу.....
Пікірлер: 47
@geoffcorey22722 жыл бұрын
Thanks for posting this, well explained process. After watching, I have successfully replaced left and right axle seals on my 2014 Silverado with 210000 km.
@BigFrogs4x4
2 жыл бұрын
Glad to help!
@stewartfirebaugh2680Ай бұрын
Appreciate the video!!! Just finished up my rear axle seek and your video helped so much!
@BigFrogs4x4
Ай бұрын
That's fantastic! Glad to hear it helped!
@ThinkAboutIt___3 жыл бұрын
Best example of a axle shaft replacement... thanks :)
@BigFrogs4x4
3 жыл бұрын
Glad i can help!
@leviscott8519 Жыл бұрын
Great video! This rear axle definitely has some extra process to it. Your video really help with how to go about the stubborn c clip and stubborn axle shaft. Lifesaver!😊
@BigFrogs4x4
Жыл бұрын
Glad I could help 😃
@pmurphy126673 жыл бұрын
the best video I have seen on this after trying to view many others. very well done!
@BigFrogs4x4
3 жыл бұрын
Thank you
@gregcoles24913 жыл бұрын
Great vid. You were very clear on what to do. Thank you 🙏
@BigFrogs4x4
3 жыл бұрын
Quite welcome
@dankeller31642 жыл бұрын
Awesome video .... Thank you for taking the time to post this and give the extra hints and suggestions God bless ... Love the verse ... Cheers
@BigFrogs4x4
2 жыл бұрын
Thanks I do these to help people when I can.
@Notaslave19613 ай бұрын
Clean the dry lock tite off the threads of the set bolt, and dry the hole for that set bolt with brakes cleaner of any oil film when you are ready to lock tite it on re-assembly.
@lambertsaldi15504 жыл бұрын
Great Review thank you 👍🇺🇲 The Vermonter
@jeremypyottjr78352 жыл бұрын
Agree with the RTV on the seal. I'm doing mine this weekend coming.
@BigFrogs4x4
2 жыл бұрын
Good luck. Fun times!
@MartinezTrucking Жыл бұрын
Very nice video. You should do a video of the parking shoe replacement next.
@BigFrogs4x4
Жыл бұрын
I would but it's not my truck and the guy who owned it traded it for a newer ram with air ride suspension. Sometime in the coming months he has me installing a bds 4" lift on it.
@austindavis91183 жыл бұрын
Thanks man had the same problem with 2012 Chevy silverado had to use a chisel to move the axle far enough to get the c clip out
@BigFrogs4x4
3 жыл бұрын
Hope it helped you some. Thanks for watching.
@gregvaldez22
11 ай бұрын
Use c clamp on hub and other side of c clamp to where the brake caliper bold hole is on the axle and it will press the axle in far enough to remove/ re install c clip. Had same issue
@mxrevival2 жыл бұрын
Good job dude
@BigFrogs4x4
2 жыл бұрын
Thank you
@TrailAdventuresTV4 жыл бұрын
Great vid! Can't wait to put a strait axel under the front of the ZR2. Nah just kidding.. Have a good one brother.
@BigFrogs4x4
4 жыл бұрын
I was looking at mine a while back. It's doable lol
@BigFrogs4x4
4 жыл бұрын
Whens your new video coming out
@TrailAdventuresTV
4 жыл бұрын
We have a trail video coming out in a few minutes. However it’s not with the ZR2. Wifey wanted to drive her Jeep.
@BigFrogs4x4
4 жыл бұрын
No problem. I like your videos anyway
@georges45624 жыл бұрын
Great video ! How’s the ZR-2 ? I just bought a 2020 and loving it so far.
@BigFrogs4x4
4 жыл бұрын
It's good. We primarily use it for long trips now since my wife has been working from home.
@mikeo.15935 ай бұрын
I suspect I have a very small seal leak on my 3500 srw would it better to replace or just keep an eye on fluid level
@BigFrogs4x4
5 ай бұрын
It will need replaced if it's getting anywhere near the brakes. Some states it won't pass inspection. But yes, keep an eye on the fluid level. Rebuilding a rear differential is very expensive.
@miguelortiz58642 жыл бұрын
Great video men, do you know the torque spec for the cross pin bolt?
@BigFrogs4x4
2 жыл бұрын
I'd have to Google it. I have done so many i go by feel. Never had 1 come out. If you can't find it let me know and I will look for it.
@sharker1613 жыл бұрын
So I’m to the point of turning the driveshaft to release the pin and it will not turn more than a few inches in both directions..Any thoughts? Yes i’m in neutral
@BigFrogs4x4
3 жыл бұрын
So driveshaft wont turn?
@BigFrogs4x4
3 жыл бұрын
Put transfer case in neutral if you can. If you have the calipers off don't hit the brake pedal
@russellvinson13863 жыл бұрын
👍🏻
@BigFrogs4x4
3 жыл бұрын
Thanks
@dw19852 жыл бұрын
I have to do this on my 2001 S10. Any idea how much a shop would charge to do it?
@BigFrogs4x4
2 жыл бұрын
It is hard to say. Depends on labor rate and if all goes well. No rust etc. Although I think the s10 is easier.
@dw1985
2 жыл бұрын
@@BigFrogs4x4 Can you take n educated guess, ballpark figure?
@BigFrogs4x4
2 жыл бұрын
If charging $70 per hr then 2-3 hr labor. Are they doing 1 side or both. 1 probably closer to 2 hr
@dw1985
2 жыл бұрын
@@BigFrogs4x4 I just got the one side to do.
@bcar1ify2 жыл бұрын
No need to put anything on the gasket. I reused mined after a fluid change it is fine.
Пікірлер: 47
Thanks for posting this, well explained process. After watching, I have successfully replaced left and right axle seals on my 2014 Silverado with 210000 km.
@BigFrogs4x4
2 жыл бұрын
Glad to help!
Appreciate the video!!! Just finished up my rear axle seek and your video helped so much!
@BigFrogs4x4
Ай бұрын
That's fantastic! Glad to hear it helped!
Best example of a axle shaft replacement... thanks :)
@BigFrogs4x4
3 жыл бұрын
Glad i can help!
Great video! This rear axle definitely has some extra process to it. Your video really help with how to go about the stubborn c clip and stubborn axle shaft. Lifesaver!😊
@BigFrogs4x4
Жыл бұрын
Glad I could help 😃
the best video I have seen on this after trying to view many others. very well done!
@BigFrogs4x4
3 жыл бұрын
Thank you
Great vid. You were very clear on what to do. Thank you 🙏
@BigFrogs4x4
3 жыл бұрын
Quite welcome
Awesome video .... Thank you for taking the time to post this and give the extra hints and suggestions God bless ... Love the verse ... Cheers
@BigFrogs4x4
2 жыл бұрын
Thanks I do these to help people when I can.
Clean the dry lock tite off the threads of the set bolt, and dry the hole for that set bolt with brakes cleaner of any oil film when you are ready to lock tite it on re-assembly.
Great Review thank you 👍🇺🇲 The Vermonter
Agree with the RTV on the seal. I'm doing mine this weekend coming.
@BigFrogs4x4
2 жыл бұрын
Good luck. Fun times!
Very nice video. You should do a video of the parking shoe replacement next.
@BigFrogs4x4
Жыл бұрын
I would but it's not my truck and the guy who owned it traded it for a newer ram with air ride suspension. Sometime in the coming months he has me installing a bds 4" lift on it.
Thanks man had the same problem with 2012 Chevy silverado had to use a chisel to move the axle far enough to get the c clip out
@BigFrogs4x4
3 жыл бұрын
Hope it helped you some. Thanks for watching.
@gregvaldez22
11 ай бұрын
Use c clamp on hub and other side of c clamp to where the brake caliper bold hole is on the axle and it will press the axle in far enough to remove/ re install c clip. Had same issue
Good job dude
@BigFrogs4x4
2 жыл бұрын
Thank you
Great vid! Can't wait to put a strait axel under the front of the ZR2. Nah just kidding.. Have a good one brother.
@BigFrogs4x4
4 жыл бұрын
I was looking at mine a while back. It's doable lol
@BigFrogs4x4
4 жыл бұрын
Whens your new video coming out
@TrailAdventuresTV
4 жыл бұрын
We have a trail video coming out in a few minutes. However it’s not with the ZR2. Wifey wanted to drive her Jeep.
@BigFrogs4x4
4 жыл бұрын
No problem. I like your videos anyway
Great video ! How’s the ZR-2 ? I just bought a 2020 and loving it so far.
@BigFrogs4x4
4 жыл бұрын
It's good. We primarily use it for long trips now since my wife has been working from home.
I suspect I have a very small seal leak on my 3500 srw would it better to replace or just keep an eye on fluid level
@BigFrogs4x4
5 ай бұрын
It will need replaced if it's getting anywhere near the brakes. Some states it won't pass inspection. But yes, keep an eye on the fluid level. Rebuilding a rear differential is very expensive.
Great video men, do you know the torque spec for the cross pin bolt?
@BigFrogs4x4
2 жыл бұрын
I'd have to Google it. I have done so many i go by feel. Never had 1 come out. If you can't find it let me know and I will look for it.
So I’m to the point of turning the driveshaft to release the pin and it will not turn more than a few inches in both directions..Any thoughts? Yes i’m in neutral
@BigFrogs4x4
3 жыл бұрын
So driveshaft wont turn?
@BigFrogs4x4
3 жыл бұрын
Put transfer case in neutral if you can. If you have the calipers off don't hit the brake pedal
👍🏻
@BigFrogs4x4
3 жыл бұрын
Thanks
I have to do this on my 2001 S10. Any idea how much a shop would charge to do it?
@BigFrogs4x4
2 жыл бұрын
It is hard to say. Depends on labor rate and if all goes well. No rust etc. Although I think the s10 is easier.
@dw1985
2 жыл бұрын
@@BigFrogs4x4 Can you take n educated guess, ballpark figure?
@BigFrogs4x4
2 жыл бұрын
If charging $70 per hr then 2-3 hr labor. Are they doing 1 side or both. 1 probably closer to 2 hr
@dw1985
2 жыл бұрын
@@BigFrogs4x4 I just got the one side to do.
No need to put anything on the gasket. I reused mined after a fluid change it is fine.