2500HD Rear Axle Hub Bearings & Axle Seal Replacement
Автокөліктер мен көлік құралдары
In this Video I replace the Rear Axle Bearings, BOTH bearings!!!
and the Axle Seal on my 2007 Chevy 2500HD CrewCab Duramax Diesel
DIY Medium
Parts: Ebay
Rear Wheel Bearing & Seal Set FOR 2001-2010 GM SILVERADO 2500HD
1 Year Warranty
www.ebay.com/itm/Rear-Wheel-B...
If you search for these Bearings and Seals, the same should work on the following
2001-2010 Chevrolet Silverado 2500HD
2001-2010 GMC Sierra 2500HD
If you like my video. Subscribe to my channel
Packwood Performance 4x4
Пікірлер: 229
Finally, a video showing both he bearings. Great video.
Great video! I was replacing my rear calipers, rotors, and pads on my 2500HD when I noticed I had gear oil collecting in the caliper on the driver side. After watching this video I was confident I could replace all the bearings and seals as well. Your video was detailed and thorough. I double checked the torque specs to be sure, and you were right on. Thanks for the help! I had zero issues.
thank you for the video .... was a lifesaver ..... i’ve replaced the seal 3x on my 08 3500hd 4wd, and it’s leaked every time .... finally, thanks to your video, i realized there was still part of the old seal (original) stuck in there!!! hopefully my 4th time will be my final one!!!!
Great video man. You helped me thru my repair like you wouldn't believe. And I also happen to think your camera and microphone work just fine :) don't think you need anything fancier since you explain and demonstrate the procedures very well. Thanks a bunch
@packwoodperformance4x474
4 жыл бұрын
Thanks! I'm glad I could help.
Great job. Like that you included torque settings, very helpful.
Thank you so much for this video, just got finished with mine on a 2003 Suburban 2500 and everything I found was for the 1500. This was perfect. And including the torque specs, absolute perfection! Much better explanation and video quality than a lot that are out there, even from some of the well known/commercial video producers.
@packwoodperformance4x474
2 жыл бұрын
Thank you. I'm glad I could help. I wish I was still making videos but I haven't had time.
Great video, have been using your video all along the way that I've been changing my bearings out today! Going smooth so far thanks to you 🤘
Great job! Thanks for mentioning both bearings. That helped a lot since most videos only show one.
This is a GREAT VIDEO!! A MUST WATCH IT! He explains everything down torque specs.
My bearings and seals are in great shape but the previous owner let it sit, the parking brake locked up and damaged the ABS ring on my 2013 duramax (unlike your '07, there's an encoder ring behind each hub instead of just on the drive shaft). Thanks for posting this, now I feel a bit more confident getting at it this week. With all the rust in my area, I'm sure every part of this is going to be worse :D
Thanks for the good explanations on seals and setting the bearings. I am 1/2 way thru my '14 Express van 2500HD / Duramax 6.6 and the hubs and axles are identical. I needed some more information that was not in the manual. Like others said, cam and video are fine. Can see and understand everything.
@packwoodperformance4x474
3 жыл бұрын
Thanks Man. Glad it helped.
Good video, if the metal ring sticks to the spindle instead of using a flat head you can use a chisel to lightly score every inch or so all the way around it. The chisel causes the sheet metal to slightly expand so as you work around the ring it will just pop off. Also putting your races in freezer for a bit will shrink them making it very easy to install in hubs. Worked as a semi mechanic for years and a full floater 14bolt is just a baby semi rear end.
@packwoodperformance4x474
3 жыл бұрын
Thank you. Yes that would work alot better. I only had my wood chisels.
Excellent video. Very methodical and shows every step. My type of video instruction.
Got to do everything you did plus have to do backing plates and all new brakes. Got a pile of new parts. My E-brake imploded a few years ago because the backing plates disintegrated
Just wanna let you know that you did a great detail job on this video and it helped a lot
@packwoodperformance4x474
2 жыл бұрын
Thanks.
Thanks so much for posting your video! I will be having to do just this...starting to see some of what you are seeing from your driver's side as well!
excellent video - thank you for the effort to put this together! Very helpful.
Awesome job, brother... After researching youtube and manuals, I did my inner and outer bearings on both sides of my 2004 silverado 2500hd... There was no information anywhere about the outer bearings and everyone had a different spec for tightening the locknut... Both sides failed pretty quick and I thought I tightened the hub too tight... So, I'm ready to do this again and thankfully found your video... I ended up putting the outer race on first, then the bearing and retainer... Now I know the bearing goes first... I use a block of wood also for the seal... Anyway, I have to thank you for this so my job won't fail this time... There's too much confusion out there regarding these full floating hubs.... You cleared it up... This video should get 100000 views... Peace...
@packwoodperformance4x474
4 жыл бұрын
Thanks Steveo66. I appreciate it. I hope it goes well.
Best video I’ve seen on this thanks
Great video. Seems as if this will basically apply to my 2004 Chevy Express 3500, with maybe different torque specs.
Damn, one hell of a good job with limited tools. Wow thanks for sharing your experience. I am probably going to have to do my truck some day. Incredible work. Thank you an God bless. 2 thumbs up from here. 🙂 👍
@packwoodperformance4x474
3 жыл бұрын
Thank you! Glad it helped.
@keithqueen352
Жыл бұрын
@Packwood Performance 4x4 were you using a brass punch?
Out of all the videos for seal replacement out there yours is most descriptive. Thank you for providing torque valves too.
Im about to do this on my 04 2500hd. Great video, thanks so much 👌
@packwoodperformance4x474
3 жыл бұрын
Thanks
Thank you! I'm a serious do it yourselfer - but for reasons unknown to me this really made me nervous. I have the GM manual online and isn't 100% clear what to do. My truck has 290K miles - I bought it used and have no idea the history. Bearings looked great (Made in USA Timken) - but it was starting to leak. I replaced the parking brake shoes and hardware and got a new Napa seal. Saved the $177 on the J tool for the seal and used a block of wood and rubber mallet - went in smooth. Now - how to exactly adjust the parking brake shoes...and to...or not to replace the seal on the other side when it currently isn't leaking???? Truck serves to haul the slide in camper - that's its whole job right now. So...ponder breaking open the other side when it isn't leaking I must. 😀
Great video. Great delivery style. I had to laugh about the comment made when you spent 15min looking for the clip....I HATE when that happens. Haha
Thanks for posting! Very helpful!
This video was well done and was a great help for completing my project. Thank you!
GOOD PICTURES AND VIDEO MATE, NICE JOB...THANK-YOU VERY MUCH !!!
I love the video you walked me right through something I have never done and it turned out good drives more smoother
@packwoodperformance4x474
Жыл бұрын
That's awesome. I'm glad it helped.
This video saved my ass with all your tips and tricks. Thanks man!
Brother, I like you I like you a lot you remind me of me when I was younger and by the way, that was very informative I was lost until I watched your video. Thank you.
Great Video! Because of your detailed explanation I am going to tackle this myself!
@packwoodperformance4x474
Жыл бұрын
It was not as hard as I thought. But it took all day.
@jameschupp2230
Жыл бұрын
Well for me it took 2 days and a morning. And then the differential was dripping a little bit, so I used the impact to tighten up the bolts and snapped a bolt and then... 4 hours later... Had to drill out and re-tapped for a larger size bolt. But really your video gave me the confidence to even think I could do it... Thanks!
Awesome job 😎👍
Nice job dude! I was going to make a video for this but but during a brake job my leak popped up so no time haha. Thanks for the torque specs too!
@packwoodperformance4x474
Жыл бұрын
Glad I could help!
Your puch is actually a "Bull Prick," used by Red Iron workers to align primed girders as they are being riveted in place at great heights.
@packwoodperformance4x474
3 жыл бұрын
Wow. Thats cool. Had no idea. Got it from my Grandpa.
Double the pleasure double the fun! Isn't 2 seals always better than one? HA! yes getting all of the seal out is a very important step.
@packwoodperformance4x474
3 жыл бұрын
Right! Let's put a new one on and smash it instantly... lol
Love it brother thanks for great tips
Thanks, and Awsome Detailed Video, You Gotta Make More!!! :)
Nice work, thanks for posting. The caliper bracket mounting bolts use medium thread locker. Be sure clean the old thread locker off before applying new. Stay gold.
you had me watching as I heard you call out tool sizes... I refer to videos to take notes down and set my tools aside. Rather than drag my hole tool box. It would be nice to know exactly what tools are needed when doing a job. Especially since I dont have the specialty tool to remove the center nut. From another video, I gather its a everthough 67037. From you, I know I need a T55 for Caliper slide out pins, 18mm caliper bracket bolts. No work on axel flange bolts... Either way, thanks
Very good video. Thanks for posting...
Good video. 👍 my rear left seal is leaking. After new seal it's still leaking on the test drive. I did put some gear oil on the seal and where it's sets on the shaft. And no silicone on the 8 bolt lol. Lesson learned. I get to do it again 😄🤣
@Chaden338
6 ай бұрын
Did redoing it with no oil on the surfaces help?
@Rodzilla408
6 ай бұрын
@Chaden338 yeah the leak stopped
96 dually rear hub bearings work the same but that little clip holding the outer bearing is a booger. Also needed a real good clip tool to reach in there
Thank you so much. I have a 2007.5 duramax i goint to do the same job.
Great video, thank you!
Awesome video thanks a bunch for sharing
great video.
FYI.... I wish it only took 37 minutes for both sides!!!! Lol. Thanks for the shade tree mechanic video 👍👍🤪
@packwoodperformance4x474
3 жыл бұрын
Lol. I know right.
@ronniebenoit4081
3 жыл бұрын
Just did the cp4 and injectors on my 13.....2 1/2 days🤯
Verry helpful video. Hi chek many and this is the best and comprehensive. Thank you very much
Very good video!
good informative video.
The hole in the center of caliper is for pushing piston open a bit more so you can get caliper off easier... just FYI
Recently replaced the bearings in my hd2500. Your vid was a great reference to keep lookin back at. I like the tire/wheel set up you’ve got on. What are they? Thanks.
@packwoodperformance4x474
2 жыл бұрын
Those are 16x8.5 MB 352 Wheels with 285×75×16 Geolander MT Tires
Thank u Sr very helpful
GREAT video!! Now I plan on tackling this myself. Question: did the kit you linked hold up well? Thanks
@packwoodperformance4x474
Жыл бұрын
I don't have the truck anymore, but I had no problems
I just want to thank you for this video and your knowledge!! I wish I could do more then just hit a like button and subscribe!! I was scared to do this and was going to send it out and pay 1400!! Yea 1400. But I think that was with new hubs. Anyways I watched this 15 times ans it made this job easy and made me confident being able to do this. Again Thank you and godbless
@packwoodperformance4x474
2 жыл бұрын
That's great. Thank You.
Hey great video. I've got to do my 2500HD GMC Sierra. This helps a bunch. Do you have any information on the axle nut removal tool, I'm striking out locally.
@packwoodperformance4x474
3 жыл бұрын
I believe I got it at Oreilly Auto Parts. They had it as a tool to rent or buy for $12 or $22 I think.
Awesome video. 1. Should I let the silicone dry a bit before tightening? 2. hould I used the gaskets I ordered? 3 any particular king of silicone?
@packwoodperformance4x474
3 жыл бұрын
No need to dry first If you use gaskets. Make sure surfaces are clean. No need for silicone. If you use silicone any gasket style should work.
Great show my friend Thank you Edit Can those E brakes be worked on without pulling everything off Mine are way over heating and I can smell them burning
@packwoodperformance4x474
Жыл бұрын
You can only adjust them with everything on. On the back side there is a hole and you can spin the adjuster for the e-brake with a flat head screwdriver.
Thank you for sharing, you are good mechanic,God bless you 😊
@vioreltorj
7 ай бұрын
How do i know if I have 10 or 111/2?
@vioreltorj
7 ай бұрын
You mean the hub?
Nice job
Thank you so much for this video
@packwoodperformance4x474
2 жыл бұрын
Your Welcome! Thank you for watching.
Great video. Makes it look a little less intimidating. One suggestion would be to change the brake pads and park brake shoes if they are contaminated with gear oil.
@packwoodperformance4x474
4 жыл бұрын
I agree. I thought I said that. I just didnt have the $$$. Definitely stops better now anyways.
Well done thanks.
@packwoodperformance4x474
3 жыл бұрын
Your welcome sir.
Made it looks easy hope it is mine are bad
Muy buen vídeo gracias por compartir very good video thanks for sharing good bless you
I have an 2012 Sierra HD 2500 , is it any different then the 2010 model? Good video man ty for the info
@packwoodperformance4x474
4 жыл бұрын
Man. I would think it would be pretty much the same. Maybe different size bearings. I can't tell you for sure. I searched for 2012 bearings but only seen them for the front. Which is the same as mine.
Had to do this three times on 6.6 duramax. I think its still leaking right now. Everything was done this way the third time. First time they didn't want to replace the seal and I was told to install not the correct way. Third time went with new seals but forewent the socket. Third time I did as I was supposed. I did add some oil to the surfaces where the seals sealed. To not tear anything. I guess that's the issue.
The 2500 as the same differential like the 3500 you have to change the hubs for the dually ???
What tool kit did you use that had that special socket? Great instructional video! Ive got a leak seal on my Duramax right now, I'll be gathering parts and tools to get started! Thanks.
@packwoodperformance4x474
3 жыл бұрын
I bought it at oreillys. Just the socket hub tool
@markw3027
2 жыл бұрын
What is the part number for the socket?
@packwoodperformance4x474
2 жыл бұрын
I belive this is it 39564113888 O'Reillys has them.
@markw3027
2 жыл бұрын
@@packwoodperformance4x474 thanks
Im.doing mine tomorrow
Hello - great video. Can you tell me what type of silicone you used when reinstalling the axle? Was it a silicone sealant/adhesive or a type of gasket maker? Thanks - GEM
@packwoodperformance4x474
Жыл бұрын
I can't remember but I was thinking it was gasket maker.
Im curious if you experienced heat on either side after noticing seal failure? You still looking for a jeep cherokee? Couldny tell on your plate but florida? Thanks
Out standing ! Subscribe I did! Going to your channel to see what else I can learn.
Awesome music
my beloved '05 LLY is making howling noise i take it in shop they said whole rear end needed replaced for $5700 including new rotors pads etc. Was your truck making a howling noise or just leaking?
Question. Is this one seal on the axle hub that separated into two pieces or is there two separate seals for the hub and the housing?
@packwoodperformance4x474
Жыл бұрын
One seal. It's 2 pieces combined to make one seal. One side is set to the axle and the other side spins with the hub.
Very helpful video. Just a quick question would there be any other reason why it would have a leak? Or is this kinda the most common reason? Changed the brakes on my 15 ram 2500 and the e brake was caked in grease
@packwoodperformance4x474
3 жыл бұрын
I need to change one on mine again. I seen a little piece of the brake hub shield where you adjust the E brake, has rubbed the hub seal to where it is leaking again. I knew it would, I already had it back together and I was tired that evening. Lol
Question: I will be doing this for the first time to my 03 duramax tomorrow. What’s the reason why you wedged the front tires ?
@packwoodperformance4x474
Жыл бұрын
Just for safety. Don't want the truck to roll on me.
Great Video, I just had to ask, Why didn't you replace the Axle Shaft Hub Gasket with a new one, instead of using Silicone sealant over top the old one ?. But just out of Curiosity did you get any leaks, or did the Silicone work?.
@packwoodperformance4x474
2 жыл бұрын
Thanks. I just didnt have any. Silicone is more accessible and works.
@packwoodperformance4x474
2 жыл бұрын
No leaks
Ty
So was the hub real loose at the beginning because the previous person installed it against that old seal that wasn't removed?
@packwoodperformance4x474
3 жыл бұрын
Yes, it was pretty loose.
Thanks!
@packwoodperformance4x474
11 ай бұрын
Your welcome!
nice
Drive in figure 8 pattern in a parking lot after fluid change/bearing /seal replacement!
How do I know what size seal I need? I tried to buy one online but there 3 different sizes and didn't know what to buy.
@packwoodperformance4x474
2 жыл бұрын
If I'm not sure I usually go to Orielys website and type in my vehicle and part. Get the part # then search for it. Amazon sells AcDelco parts for way less
Do you think the leftover seal part (around 00:13:00) is a separate part for the seal to run/scratch on? So that the seal won’t damage the big axle (or whatever it’s called), aka, grind a grove on it. Thanks!
@packwoodperformance4x474
2 жыл бұрын
No. As you see in the first seal I take off. They come apart over time. The seal is 2 part. It spins like a bearing. And the one that was left on was smashed way far in from someone putting a new one on without removing the old one. That's why there was so much play in that hub.
@jrm163
2 жыл бұрын
@@packwoodperformance4x474 I’m still confused. The pinion seal definitely has such a sleeve for the seal to run on, but seem GM has taken it away from the axle seals. Are the new axle seals like bearings too? Thanks!
@packwoodperformance4x474
2 жыл бұрын
Now I'm confused. It's the exact opposite of a pinion seal I think. A pinion seal is secured on the outside when a hub seal is secured on the inside. So when the wheel spins. It's like a hulahoop on the axle shaft. Not exactly but kinda like that
@jrm163
2 жыл бұрын
@@packwoodperformance4x474 right. So either seal needs to run on a sleeve, or it will make a grove on the axle (or yoke), or metal to be universal.
@jrm163
2 жыл бұрын
@@packwoodperformance4x474 check out this please: kzread.info/dash/bejne/god3x9yvp9jgkqQ.html
Anyone know where I can get that socket and what size/type it is?
@packwoodperformance4x474
3 жыл бұрын
I believe it's a 2 3/4 - 9 pin. You can rent or buy at Oreillys for $12 or $22. I can't remember, sorry. But they know which one.
So, there are TWO grease seals on each hub?? It looked like you pulled one off, then pulled another one in the same position as the other. Then the left over metal from a seal that should have been removed. I thought there was just one seal per hub.
Hoping hub isn't damaged or that chaft
thank you owe you a cold beer!!!
Well this work for a 2000 Silverado 2500? And is it the same parts?
@packwoodperformance4x474
3 жыл бұрын
Yes I believe so. The parts are in the Description and has the years it works with.
PLEASE READ! If you are doing this job on any truck thats rusty.. MAKE SURE the vent on the top of the axle tube is clear... If you have rusted up hole inside it will build up pressure and keep blowing seals out. Its more common than you think.
having trouble getting the passenger side axle to go in, been at it for an hour, any tips? driver side is in, great video
@packwoodperformance4x474
2 жыл бұрын
If I remember correctly I had a time on one side. Slowly turning it and holding it center. It's tough. I can't remember if there is a mark or not.
@rosslingwall6955
2 жыл бұрын
@@packwoodperformance4x474 are both axles the same size, trying not to get frustrated, just having a hell of a time getting it in
@packwoodperformance4x474
2 жыл бұрын
I Believe they are the same.
@rosslingwall6955
2 жыл бұрын
mine has a white mark on the shaft, maybe that is the top, will keep trying lol
@packwoodperformance4x474
2 жыл бұрын
If you look at the splines. Is there a Groove that is wider? To go on 1 way?
Can you use a press to put new bearing in hub?
@packwoodperformance4x474
Жыл бұрын
Yes I'm sure you could if you have one big enough.
@sirsweetness6047
Жыл бұрын
@@packwoodperformance4x474 I used a 20 ton. It was more than adequate. I would say that one could use a 12 ton if they have it.
If one seal is good, two seals are gooder:)
11.5 or 10.5 also are parts the same ??
@packwoodperformance4x474
3 жыл бұрын
I can't remember, but I'm pretty sure they are different.
outside bearing race should not bottom out! Bearing cage is much taller than the race. Race should be pressed just pass the retainer ring ridge.
@scflooring8658
3 жыл бұрын
Hi can you explain little more thank you.
@packwoodperformance4x474
3 жыл бұрын
Like he said of course it's not supposed to bottom out. I really meant if it does bottom out you can turn it over and tap back like explained in the video. When your tapping it down into place, if you can see the groove that the ring pops into you know you're ready to stop tapping down.
@scflooring8658
3 жыл бұрын
Ok thank you very much getting ready to do mine this weekend trying to find the right way to do it and your video is the best one I've found
Doing mine now..... who's parking brake assembly is upside down, yours or mine??!?
@packwoodperformance4x474
Жыл бұрын
One side is opposite the other side I believe
@jaxturner7288
Жыл бұрын
That’s funny AF. 🙏 We all got one upside down.
At the beginning of the video you wiggle your rotor in and out. That won't help you much when you are you shooting for a bad bearing. Play on the vertical axis is what you are looking for.
@packwoodperformance4x474
Жыл бұрын
I wasn't checking for bad bearings. The hub seal is what I was fixing. I just did the bearings also.
@packwoodperformance4x474
Жыл бұрын
If you watch the full video. Someone had put a new seal on with part of the old one still on.