HOTRC DS600 Stroke Adjustment and Calibration Settings
What should I do if the remote control can only move forward, but cannot move backward, and cannot turn left or right?
First of all, we need to consider the amount of travel. If you cannot turn left or right, this may be because the amount of travel is set to the minimum, or it may be that the calibration has not been completed. We can adjust the amount of travel first and set it to the maximum. If the amount of travel is adjusted After reaching the maximum, turn left and right normally with one pass, which means that it is a problem of stroke volume. If it still cannot be turned left and right, it means that it is a problem of calibration (if the stroke volume is set to the minimum, there is no way to adjust it back through calibration)
Secondly, we consider that the calibration has not been completed. For example, if you can only move forward, but cannot move backward, or adjust the over-travel, there is still no way to turn left or right after one pass. At this point, we can reset the calibration
Пікірлер: 22
안녕하세요 hotrc ds-600 구형은 구할수없나요..? lcd없는 구형 송신기 수신기가 꼭필요합니다. 호보보드rc 신형을 쓰면 스티어링이 안됩니다.
How can i factory resst the Controller? Would love to get some help as it is not working properly and i want to set it back to standard settings. I couldn't find a solution and here's no Video about it.
Hello) At what range is the most stable operation of the device possible? I am interested in a device with the possibility of radio control at a distance of 1-2 kilometers on the ground. Which model from the list of your devices would you recommend me?
@HotRC-Sophy
Жыл бұрын
HT-8A remote control, the bottom distance is about 400 meters (without occlusion), and the air distance is 600-800 meters
@user-cv2ir9zr7w
Жыл бұрын
@@HotRC-Sophy Are your items on Aliexpress?
@HotRC-Sophy
Жыл бұрын
@@user-cv2ir9zr7w You can search directly on AliExpress or Amazon, you will find it
hi there, I have the 2 esc joined togethe with y-harness, I have hotrc ds 600 with the screen, it works fine backward and forward but in direction it can go to right but if I steer to left it goes backward I tried calibrating but it did not work , any suggestion? thank you in advance
@HotRC-Sophy
Ай бұрын
Please contact our facebook account and send a picture of your wiring in a private message
@HotRC-Sophy
Ай бұрын
Facebook account name: Sophy Hotrc
How do I adust the stroke with the new DS600 with the LCD screen? These instructions don't work for my new one.
@friendlymaendi
2 ай бұрын
From the instructions of the new LCD remote: The stroke of each channel of the remote control can be adjusted. 2. Setting method A. Remote control shutdown status, B. Press and hold the channel key [ 5] of the remote control first, and then turn on the power switch of the remote control; C. By pressing the corresponding channel button to adjust the stroke amount of the corresponding channel, the adjustment process can observe the stroke amount of the rudder in real-time D. Long press the channel key [ 5] to exit the setup. [Note: The default stroke amount is the maximum, and there are 10 segments from the maximum stroke amount to the minimum stroke amount, which can be adjusted in cycles.]
@friendlymaendi
2 ай бұрын
There ain‘t no feedback on the throttle servo, but the throttle trim does adjust its stroke when in this mode.
@HotRC-Sophy
2 ай бұрын
OK, I will send you a manual for the DS600 remote control. I hope it will be helpful to you.
Hello, is there a way to remove the sound from the controller? i need it to be silent
@HotRC-Sophy
11 ай бұрын
What function did you set on the remote control, and then there is sound
please ... i have set the esc to a forward and reverse but the stick in the control is not centered... the neutral stick position mkes the motor slightly run cw,,,, and the neutral point is little below that,, HOW CAN I MAKE IT BE AT EXACT CENTER ?
@HotRC-Sophy
11 ай бұрын
Did you adjust the failsafe function?
@marcelocmj6680
11 ай бұрын
@@HotRC-Sophy not yet because wanted this to be ok before failsafe
@marcelocmj6680
11 ай бұрын
do I need to do failsafe configuration before? will sol e the issue?
@HotRC-Sophy
11 ай бұрын
@@marcelocmj6680 Are you using two-way or one-way ESCs?
@marcelocmj6680
11 ай бұрын
@@HotRC-Sophy flycolor 150A with reverse option programmed