Bravoo.majstore svaka cast

Great build.. Few things i saw.. Your mount braket should have a cross support in the triangle . you need a 220V welder but as this is a walk behind it should be good.. Plasma cutters are awesome as well.. also a strip of steel in front of your rubber cutting edge would strengthen as well... excellent build though

Nice to see a young man welding and fabricating!

انت انسان مبدع .. لا بد اختراعاتك تتحول الى مشاريع .. وتأخذ نسبة ارباح منها تحياتي متابع عربي

Damn dude..... That looks like more work than just shoveling

@toddkratzer7953

5 жыл бұрын

Exactly, well said.

Уже третий сезон убираю снег с помощью отвала и снегоуборщика. 1. Отвал у меня тоже ворочается вправо, влево , но на один бок убирать гемор(очень медленно, 48 раз проход по одному месту).2- Сделал отвал похожий на ковш: увеличил вдвое высоту(такой же как на видео стал) и приварил боковины. Реально быстро и эффективно грести снег только прямо( но сразу скажу, что усилий приходится прилагать совсем не мало, сам мотоблок не поедет, буксует , не знаю как на гусиницах). Сгребаешь в большие кучи, а потом либо меняешь отвал на насадку-снегоуборщик, если снег еще не слежался (около половины поможет перекидать, потом все равно лопата), либо сразу лопату в зубы и вперед - пахать. 3. Одна насадка-снегоуборщик тоже не вариант( желателен полный штиль, снег 20 см, не сырой) . Но лучший и верный друг все равно ЛОПАТА. При любых раскладах работу заканчиваешь с ее помощью. Зато тренировочка еще та! И главное: вспотел, спина начала подмерзать, иди и переоденься в сухое. Тогда труд на пользу.

Damn. I'm tired just watching him make that. Genius at work!

Excellent build! Just one bit of advice. If you were to put more of a curve on the blade it would get under the snow and roll it off to the side easier.

Super video and music. Thanks

Young fella, that's some impressive fabrication skills, and a well done vid.

Idei geniale! Bravo!👍👍👍

A real professional indeed. Wish I could buy one.

Nice work ! Watch your neighbors for when they put gas grills out for garbage - those stainless steel lids are Great for making snow plows for; tillers, and even in front of snow blowers for light snow & slush. (make sure your plow will clear augers - if used accidentally. 😉

Somewhat easyer than the shovel, a good job jobbed.

Very cool way to have fun in your shop and way more fun than shoveling snow lol thanks for another great vid! :)

Svaka čast bratee

Cool little snow plow that was good idea

Sve odlično, jedino je kultivator pre lagani

He made something for little money that proves the concept. He used various tools, while making the plow... a reward unto itself. What did you make, today?

Odlicna stvar samo tako nastavi poz brate moj 👍👍👍🔥

Might uses this idea on my snowblower, when the snow is slushy and it clogs up the snowblower.. use the power of the six-speed snowblower to push the heavy slushy snow off the driveway, convert it into a snow plow. Maybe just bolt on a metal snow shovel blade. ❄️🤔

Your idea is very good! Maybe you can improve your device, for example, you can place two bags of sand on both sides of the cultivator to make it heavier, then the wheels of the cultivator will not slip. Thank you for this great idea!

@user-pe4ng8xm7u

5 жыл бұрын

'

This guy paid attention in shop class! Nice job.

Man you sometining else♥️ Pozdrav from Chicago

Good one and no snow on a windy day blowing all over you when you have to go against the wind 💨⚒🛠👍

Jak widać taki motorek można do różnych robót wykorzystać 👍

Well Done. A shorter height blade and more weight over tires might help. I made a similar pusher that attaches to the front of the rear half of a snowblower.

Nice job, as long as you have the right equipment. 👍👍👍👍

Молодец. Требуются небольшие доработки, но неплохо. Со сваркой потренируйся.

Good Design!! Excellent Job.

A nice build. I wish I could weld like that and may soon learn how to. Your device reminded me of a plow my father built many years ago and attached to a Standard Twin tractor. If you're interested there are several videos of Standard Twins on KZread. it's a smaller garden tractor with large wheels on the front and on my dad's version smaller wheels on the back. I've used it for many years to plow snow. However, even though it is much heavier than your tiller it was still difficult to use with heavy or deep snow. Having the blade angled like that pushes the machine to the side quite easily. And with the blade perpendicular to the axis of travel simply not enough traction. Even with chains on the large tires, probably 40 inch tall and weighing in the neighborhood of 150-200 lbs each ( I can barely stand one up vertically from a laying on the ground position. My dad added lead weights to each tire.) and the added weight of the tractor itself it does not have the ability to push a lot of wet heavy or deep snow. Even though there is probably in the neighborhood of, I suspect, at least 500 lbs distributed over the two front tires that drive it. It works though for lighter snowfalls! Well, worked, the motor finally gave up. I'm guessing that you have found that it's not very effective for anything other than light to moderate dry fluffy snow plowing. You should have contacted me before you built it! I could have cautioned you. But then you wouldn't have had the fun of building and testing it. Again, nice build.

Odlicno samo produzi tako, pozdrav iz Makedonije ;)

@DShomemade

5 жыл бұрын

poz iz Hrv

It's working perfect, well done

Small set of tire chains an you got it kid! Nice!

@zoricalevic9928

3 жыл бұрын

Laonoa😘😘

Wow all that in 15 minutes, lol. Great job

First time seeing me and you're very talented yes you can buy it for cheever lady but doing it yourself that's a challenge and apparently you like a good challenge keep up the good work

Респект!!!👍👍👍

За идею 👍 Ну много минусов, всё таки лучше ручной снегоуборочной машины ни чего пока нет.

Cool idea, but a snowblower would work a lot better 🤷‍♀️

Put it on a riding mower or atv. I hate snowblowers almost as much as snow shovels. They're almost as much work..

Great work Dr, also luv your bike, ♥♡♥

To se čekalo.. Čitaš mi misli legendo ❤

@DShomemade

5 жыл бұрын

hehehe

Svaka cast

I dnt know what say. You are amazing. Wow I ❤️ your video 👍

Best idea ever

THAT IS FRIGGINNN COOL....

MIO standard Osjek, HONDA. Odlicni motokultivatori, a ideja ti super i ne kosta puno, jer ima i kupiti otiginal... da nije hladno odmah bi iskopirao ideju jer imam isti. Bravo. Pozdrav iz Srbije!

@DShomemade

5 жыл бұрын

ovo je originalni hondin motokultivator ali imao sam i mio standart f430 tak nest :D Taj je vukoooo ko lud :D hehehe poz iz Hrvatske ;)

@goranstojkovic5838

5 жыл бұрын

620y 😀 Jel MIO ne proizvodi vise motokultivatore?

Interesting video, avtor 💪 💪 💪 💪 thank you All power

Ну ты даеш слов нет братан дай БОГ тибе здаровия

Nice work young man!!

Nice job young man.

Cool idea. 1. Thinking ... hmmmmm wonder if I could do that with my tiller. 2. Rear Tiller ... I could just remove the tines in the winter. 3. Would have to find some scrap steel and learn to weld. 4. Wonder could the drive wheels be slowed down? Or could I find tire chains for grip hmmmmm. Wondering .... Why something like this doesn't exist today. You buy a rototiller and it's used, what at most, twice a hear .. To prep the garden and to end the garden ..... It should have a mower attachment / and this a snow pushing attachment or even blower.

That was a beautiful job that you made that is really awesome

Odlična ideja hvala ti

Good idea, adding weight to the wheels would help.

Awesome build up

imas ti potencijal svaka cast majstor

Bravoooo

Молодец чувак!!!

20000+. Лопата чистит и это главное.

Good job!

Nice project.

nice work mate smart idea!!

I liked your innovation

Creativity is nice. Doesn't seem to work too well though. Possibly adding rear weights 🤷‍♂️

Odlicna,vido pozz sam nastavi brate

Predobra ideja!😀😀

Hmm, hardening the mold board behind the cutting edge with weld. That's pretty slick. Nice work!

A rear v blade would be great, no fishtailing, plus if your handles flipped over and you reversed, now your v blade becomes a v scoop. 😊 good luck 🤞

You are the best doctor👍♥️

another great build mate well done :) I will have to do one meself :)

good job doctor!

BRAVO! Felicitari!

Once again...you have done it again...another great idea..great build...great project....very creative...keep those videos coming !

Looks like a fine machine, maybe add some weight to it and it would be a beast , nice build!

Nice. But all that work! I've bought several plows like that for $40, commercially made, more heavy duty.

Very goog idea👍

Nice work👍☺

Slijedeče Vodena pumpa od trimera☺

@DShomemade

5 жыл бұрын

agahahaha

Good creativity ! Congratulations bro !

Svaka ćast. Imamo isti hoby

@DShomemade

5 жыл бұрын

;)

Buen trabajo DS. Saludos desde Santander.

tuyết rơi đẹp quá ♥️👍

more weight on the wheels and maby some chains/spikes and that would be an effective tool. nice work.

If its a wet heavy snow like that, that thing is mainly useless without any real weight added to the machine

Should have use the shovel it would have take les time

Svaka čast majstore. Super stvar. Možda samo ne može na brdovitom terenu.👍👍👍 Samo još da napraviš lance za kultivator i ekstra.

@DShomemade

5 жыл бұрын

Daa obavezno neke lance i togove trebam stavit ;)

Dobro si napravio

BIG like again

PA STA RECI ? BRAVO !

Very good 😚

Nice

Laik 👍

Do snow chains and make wheel weights

Good work.

Works great for that 1/2" of snow you get twice a year I bet. Sorry, not trying to be mean, this is very creative. It'd be much better on something a little more substantial though like an ATV with snow tires or chains. Cheers from the north east.

From Greece. Very good

Super!

Дал бог человеку время и желание

Svaka čast

@DShomemade

5 жыл бұрын

:D