That baffle is there for a reason!! Diffuser. You need a pre filter on that hard filter.
@theokunick15776 ай бұрын
Walbro actually has a plant in Tianjin, China. It seems like the pro model already has many of the upgrades a lot of people recommend on doing to the standard versions.
@generalkayoss73476 ай бұрын
I just ordered one of these to mate with a 36" bar and an Alaskan mill. Plan on milling some hardwood slabs to eventually turn into tabletops. You got a much better deal than me, I ended up paying just under $500 after taxes ordering from Amazon.
@Man-Time
6 ай бұрын
I did get a really good deal. I like mine and it’s been good to me so far. Best of luck
@generalkayoss7347
6 ай бұрын
@@Man-Time I ordered a Stihl chain tensioner and a better oiler for it as well, they seem to be some of the weak links in these saws from the research I've done. I still think it's going to be very worth it as long as it doesn't give me any major issues!
@Man-Time
6 ай бұрын
Those are the things that I want to upgrade also. I did replace the fuel line to the carb as mine was leaking
@Mightycaptain
6 ай бұрын
Which OEM Model parts are direct fit? 660 or 066?@@generalkayoss7347
@Abeene
2 ай бұрын
You did fine, I ordered when you did. Holtzforma's shipping was over $100, after fees it was much closer. I went with Amazon to get their warranty and transaction simplicity.
@juledorenАй бұрын
Been running a 42” bar for milling on this saw, i also opened it up a bit for performance, its still running to this day
@zeromark2027 ай бұрын
The 660 is the best model they have cloned. I won’t waste my money on any of the others. My 660 clone has been ok for when needing to run a 36” bar.
@Man-Time
7 ай бұрын
Agreed. It’s a pig to lug around and a bit of a gas hog, but pulls that 36” pretty good.
@chrismuncey38619 ай бұрын
I have a g660 pro good saw's. With some work they wake up big time. I threw the piece under the filter away and its not had any problems.
@902hand79 ай бұрын
I only have 1 clone and that's likely my limit but I do think they have a place in everyone's saw collection as long as you don't mind wrenching on saws, upgrading some parts to OEM and aren't depending solely on one to to make a paycheck...
@Man-Time
9 ай бұрын
Agreed
@rosskstar4 ай бұрын
When you order from Farmertec, was there any import duty to worry about or shipping they charge for later?
@Man-Time
4 ай бұрын
No additional fees for me in the US
@Bob-ux8sn9 ай бұрын
Just for fun you make it 98cc with a dome piston really make it pop put cheap Chinese cylinder highway piston with caber rings on a 066 with a red light from the 90s have fun with it .
@Man-Time
9 ай бұрын
It hard to not have fun with a chainsaw😁
@lukereynolds99079 ай бұрын
Do you use echo red armour 2 stroke oil mate
@Man-Time
9 ай бұрын
Yes @ 40:1
@claudiurus59832 ай бұрын
I don't like the fact that they are sell whitout guide barr an chain.They should be banned from selling without these.Greetings from Romania!
@scottfoster24879 ай бұрын
I will tell you you need to really look into a neotec. Neotec has a better build quality and they offer some pro upgrades. I jave no dislike for any clone if it works and does the job. Grease the base of the airfilter ,these clone air filters are garbage,,go get a max flow oil air filter kit.. Beotec comes with a better tool kit dir sure.
@Man-Time
9 ай бұрын
Yeah I got a great deal on this one. But I have a neotec stihl spare parts kit that has saved me a few times. The tools kit is very nice. I can’t speak to the saws they make
@billbennett-rk8gm4 ай бұрын
You and your bob the builder tools Have already said this saw is junk so why even buy it If you want a stihl then buy it and stop bitching if you are looking for a Lincoln you don’t buy a pinto
Пікірлер: 24
That baffle is there for a reason!! Diffuser. You need a pre filter on that hard filter.
Walbro actually has a plant in Tianjin, China. It seems like the pro model already has many of the upgrades a lot of people recommend on doing to the standard versions.
I just ordered one of these to mate with a 36" bar and an Alaskan mill. Plan on milling some hardwood slabs to eventually turn into tabletops. You got a much better deal than me, I ended up paying just under $500 after taxes ordering from Amazon.
@Man-Time
6 ай бұрын
I did get a really good deal. I like mine and it’s been good to me so far. Best of luck
@generalkayoss7347
6 ай бұрын
@@Man-Time I ordered a Stihl chain tensioner and a better oiler for it as well, they seem to be some of the weak links in these saws from the research I've done. I still think it's going to be very worth it as long as it doesn't give me any major issues!
@Man-Time
6 ай бұрын
Those are the things that I want to upgrade also. I did replace the fuel line to the carb as mine was leaking
@Mightycaptain
6 ай бұрын
Which OEM Model parts are direct fit? 660 or 066?@@generalkayoss7347
@Abeene
2 ай бұрын
You did fine, I ordered when you did. Holtzforma's shipping was over $100, after fees it was much closer. I went with Amazon to get their warranty and transaction simplicity.
Been running a 42” bar for milling on this saw, i also opened it up a bit for performance, its still running to this day
The 660 is the best model they have cloned. I won’t waste my money on any of the others. My 660 clone has been ok for when needing to run a 36” bar.
@Man-Time
7 ай бұрын
Agreed. It’s a pig to lug around and a bit of a gas hog, but pulls that 36” pretty good.
I have a g660 pro good saw's. With some work they wake up big time. I threw the piece under the filter away and its not had any problems.
I only have 1 clone and that's likely my limit but I do think they have a place in everyone's saw collection as long as you don't mind wrenching on saws, upgrading some parts to OEM and aren't depending solely on one to to make a paycheck...
@Man-Time
9 ай бұрын
Agreed
When you order from Farmertec, was there any import duty to worry about or shipping they charge for later?
@Man-Time
4 ай бұрын
No additional fees for me in the US
Just for fun you make it 98cc with a dome piston really make it pop put cheap Chinese cylinder highway piston with caber rings on a 066 with a red light from the 90s have fun with it .
@Man-Time
9 ай бұрын
It hard to not have fun with a chainsaw😁
Do you use echo red armour 2 stroke oil mate
@Man-Time
9 ай бұрын
Yes @ 40:1
I don't like the fact that they are sell whitout guide barr an chain.They should be banned from selling without these.Greetings from Romania!
I will tell you you need to really look into a neotec. Neotec has a better build quality and they offer some pro upgrades. I jave no dislike for any clone if it works and does the job. Grease the base of the airfilter ,these clone air filters are garbage,,go get a max flow oil air filter kit.. Beotec comes with a better tool kit dir sure.
@Man-Time
9 ай бұрын
Yeah I got a great deal on this one. But I have a neotec stihl spare parts kit that has saved me a few times. The tools kit is very nice. I can’t speak to the saws they make
You and your bob the builder tools Have already said this saw is junk so why even buy it If you want a stihl then buy it and stop bitching if you are looking for a Lincoln you don’t buy a pinto