High-Grip Race Suspension Conversion For The Fox Body: Part 2 - Engine Power S1, E13
Автокөліктер мен көлік құралдары
How-to turn a stock Fox-body into a competition ready corner carver with suspension, big brakes and cage.
Part 1: Coyote Aluminator V8 Turns a 4-Cylinder Mustang Into Auto-Cross Beast: Part 1
• Coyote Aluminator V8 T...
Follow POWERNATION Everywhere:
www.powernationtv.com
/ powernationtv
/ powernationtv
PARTS USED IN THIS EPISODE:
American Powertrain Systems: New Tremec MAGNUM 6-Speed for Ford, 26-spline input, close ratio
More Info: pntv.us/pn_pt_627
American Powertrain Systems: Transmission Crossmember, X-Factor, Aluminum, Silver Powdercoated, Ford, T-56, Each
More Info: pntv.us/pn_pt_628
Auburn: Differential, Auburn, High Performance Series, Limited Slip, 31-Spline, Ford 8.8 in., Each
More Info: pntv.us/pn_pt_625
AutoZone: OPTIMA Battery, Yellow Top, 12V, Deep Cycle, 750 Cold Cranking Amps, Top/Side Post, BCI Group 34/78, Each
More Info: pntv.us/pn_pt_630
Dupli-Color: Paint, Engine, Enamel with Ceramic Resin, Gloss, New Ford Gray, 12 oz., Aerosol, Each
More Info: pntv.us/pn_pt_620
Flaming River: 1979-93 5.0 Mustang Manual Rack & Pinion - 15:1 Quick Ratio
More Info: pntv.us/pn_pt_626
Ford Performance Parts: 5.0L (302 cubic inches),9.5:1 compression ratio for supercharged applications,Mahle Hard Anodized forged pistons with Graphal low friction coating, Manley H-beam connecting rods with ARP bolts, Uses production Mustang GT aluminum cylinder block, large rear sump oil pan with 8qt capacity,Tuned composite Mustang GT intake manifold with drive by wire 80mm throttle body, Four-valve-per-cylinder aluminum heads with roller-finger followers, Heads feature Boss 302 Valve Springs
More Info: pntv.us/pn_pt_622
NOS: Nitrous Bottle, 12.8 lbs., Carbon Fiber, Each
More Info: pntv.us/pn_pt_629
Richmond Gear: Gear, Ring and Pinion, EXCel, 4.10:1:1 Ratio, Ford, 8.8 in., 10-Bolt, Set
More Info: pntv.us/pn_pt_624
American Muscle: 2003 Cobra Black Wheel - 17x9 (94-04 All)
American Muscle: NITTO NT01 Competition Radial Tire - 255/40-17 (94-04 All)
Kinsler Fuel Injection: Custom Honda K-Series Intake Manifold
Kinsler Fuel Injection: K-140 Fuel Pressure Release Valve, Fixed and adjustable ranges from 20 -160 psi. Vacuum/boost referenced, gas or methanol
Maximum Motorsports: 1990-93 Mustang Maximum Grip Box: MM K-member (with 2-point brace), MM Front Control Arms, MM Torque-arm, MM Panhard Bar, MM XL Series Full-length Subframe Connectors, MM Coil-over Conversion Kits,Front and Rear Coil-over springs, MM Caster/Camber Plates, MM HD Rear Lower Control Arms (no spring perch or swaybar mount), KONI HD series struts, KONI HD series shocks, MM Adjustable Rear Swaybar, MM Aluminum Steering rack Bushings, MM Solid Steering Shaft, MM Bumpsteer Kit (adjustable outer tie-rod
MPS Auto Salvage: 94/95 Mustang Front Spindle
MPS Auto Salvage: Factory Fox Body Mustang Dual Exhaust Mounting Bracket
North Racecars: Complete North Racecars rear cobra brake kit. Fox Length hub centric axles (optional 31 spline), patented cobra axle flange brackets, new cobra rotors, new cobra calipers, pads, soft lines (optional braided 3 line kit from MM), mounting hardware, banjo bolts crush washers and E brake cables: everything for the rear end.
North Racecars: FX Front Big Brake Kit- For installation on a Fox Body (1987-93) use 1994 or 95 Mustang spindles:2 NEW 13 inch rotors vented, (not cross drilled or slotted) 2 NEW Aluminum Twin piston calipers with mounting brackets and pads(blank they do not say Cobra), 2 NEW banjo bolts and crush washers, 2 Maximum Motorsports brake line kits
The Industrial Depot: Fasteners, Hardware and Shop Supplies
Пікірлер: 171
Maximum Motorsports threw their entire catalog at this car. I could only imagine how well this car handles and how fast it is with that coyote
@narmale
3 жыл бұрын
its night and day... its like driving a miata now ^.^
@jamesgeorge4874
3 жыл бұрын
Almost as fast as it would be with an LS3.
@narmale
3 жыл бұрын
@@jamesgeorge4874 🤮 hardly, try a 454 cleavor with CHI heads, LS aint got anything on cleavors
@jamesgeorge4874
3 жыл бұрын
@@narmale Richard Holdner has taken a *stock bottom end* LY6 north of 1500 HP. Heads, cam, springs, injectors, and 29 lbs of boost. It would cost more to equip your 60's era clevor with a rotating assembly that would survive 1000 HP, than it would to build the entire 1500 HP LS, my freind, this is 2021, not 1970.
@narmale
3 жыл бұрын
@@jamesgeorge4874 not talking about 1970 pfft... talking ford racing's 351z block
7:23 gottem
@RetroCheater81
3 жыл бұрын
beat me to it
Huge Maximum Motorsports fan here. They're one of the best things that ever happened for the Mustang community.
@narmale
3 жыл бұрын
10000%
@mchristr
2 жыл бұрын
In 30 years of playing with Fox Mustangs I've never seen customer service like Maximum Motorsports. And their products are top shelf.
@seeunow44
Жыл бұрын
Yes!!! Excellent quality and R&D!!
We seriously need all automotive channel's showing their support for the RPM ACT.. I always enjoy these shows been watching power block since I don't know when..
@zaceryhammond1144
3 жыл бұрын
I’m all for taking cars about to rust in half off the road (not patina surface rust ) but taking cars that are Safer lighter and better handling off the road is insane and stupid like the idiots that drive Tesla’s in a country run on coal and gas
I’ve got this exact same maximum Motorsports kit on my 93. The car sticks to the ground so nice now. It’s no joke and worth every penny! Very easy to install too.
@sjcst35
3 жыл бұрын
How is the rear ground clearance under that torque arm ?
@chrisvela5462
2 жыл бұрын
Good to hear, I'm looking to throw all this in my New Edge
I LOVE THE CLOSE TO $100,000 you throw at this car!!!
@chrisvela5462
2 жыл бұрын
The full suspension kit is 6 grand. At most this car has to be 40,000.
Panhard bar and torque are the best mod done to my car, it hooks in corners and in straight line . No more ass end passing me!
@trillrifaxegrindor4411
3 жыл бұрын
make it like my car came stock,then they arent tail happy go carts....ive upgraded my torque arm too!
Fantastic suspension build. I would have loved to have seen some testing on the stock setup vs this though, Seeing the huge gains would have been fun to watch
That thing gone handle like a beast😉
As a man who has taken a steering wheel to the chest I can very much appreciate the collapsible shaft.
@chrisvela5462
2 жыл бұрын
Aw man, glad you're still here brother
7:23 Deeze nuts😂😂😂😂 They have a stronger grade then u find at the hardware store 😂😂😂😂😂
@mechanicalking
3 жыл бұрын
Lmao
Great episode, guys. Now I wanna see some on car camera angles of that fancy suspension doing work on the track and under load.
More content like this please. Watching engine builds is getting old for me.
I'm impressed with this episode. I was starting to loose faith. They resurrected this little fox in style.
@MrAcuta73
3 жыл бұрын
Lose* It doesn't need tightening nor did it escape. Sorry, but that drives me nuts.
@robertelee6712
3 жыл бұрын
@@MrAcuta73 You may want to work on your punctuation. I wasn't planning on being graded for my grammar. I catch 90% of my mistakes but I don't sweat the 10%. I'm well aware of the difference between lose and loose. " It doesn't need tightening, nor did it escape." I fixed your incorrect sentence.
7:20 HA, GOTEEEEEM HAHA, Goteem
Measuring in millimeters makes me happy 🤘 So much easier to use.
@trillrifaxegrindor4411
3 жыл бұрын
if you cant do both,you cant math
@KingJT80
4 ай бұрын
@@trillrifaxegrindor4411we can convert but MM is better
Yikes this setup is ridiculous! Wow I’m impressed!
Awesome set up guys just awesome.
Wow. Jack Hidley and Richard Oben in the same video. Awesome
This looks very familiar, almost finished with my front install and collecting parts for the rear.
yeah buddy DEEZNUTS!!!!!
@absoluterage1993
3 жыл бұрын
Was wondering if anyone else caught that
Great vid!!!!!!!!!!!!!
I need this entire set up for mine😤
@7:24 I’m dead!! Lol
Aren’t subframes connectors supposed to be welded up with the car’s suspension loaded?
@KingJT80
4 ай бұрын
Should be Mine was. But I also didn't take my entire car apart either
Old episode. I think it originally aired 5-6 years ago.
@rod928s4
3 жыл бұрын
ya, true enough Carson!
@allenl9031
3 жыл бұрын
2014 per the end credits.
My 89 fox body mustang caught fire from an ignition switch Fire. Ford finally recalled them 8 million for the first Recall. 14 million in all.
make sure to keep all the factory parts like deez nuts😂😂😂
When Tony Stark builds a Fox Body
Thanks!
Totally awesome system.I’m an engineer I should know
Millimeters for accuracy and ease.
Why are we advertising k-series kinsler intakes lol on a fox body build video
Nice job men. Is there clearance for the street? The rear center traction arm looks like it will scrape the pavement , could be camera angle too.
FYI... When doing cobra brakes... the SC terminator front calipers have slightly larger pistons.
I don't know why I'm watching this. I'm just DREAMING of a panhard bar for decent rear end solidity.
Suspension, nice. G Force Tamer.
I used to host maximum Motorsports website like 20 years ago!
Nice
I need them to build my car 🔥🔥
7:23 “deez nuttz” 😂😭😭
would be awesome to try out. where i live the roads are shit so it would be destroyed. maybe a little track time.
hello I have a question what part number are the rear coilovers I have a fox I would like to use those same since you say they are for 200 pounds
Im by no means a ford guy but that setup is pretty freaking awesome. I'm little surprised the brake routers aren't drilled and slotted tho.
@NGG1983
3 жыл бұрын
a lot of track guys dont use drilled or slotted rotors because they're more likely to suffer cracking. also they lower your braking surface area overall. basically people just think they look cool and that's why they exist, lol
@trillrifaxegrindor4411
3 жыл бұрын
thats more for "prettiness"
@chrisrcarraher8800
2 жыл бұрын
Drilled rotors are bad, the holes create a weak point to crack once put through extreme heat cycles. However, the slots are good for trapped gasses to escape allowing even brake pad contact.
On my 90 hatch I want to mini tub it for wider tires. Will I be able to use a coil over shock relocater kit with this set up? I want to auto cross and do some amateur road cource. I also want the Pro Street look for cruising and maybe hit the drag strip occasionally. I would like an all in 1 experience. Enjoy the content. Y'all keep turning those wrenches and be safe.😁👍
The best
I noticed you did not install the headers on motor before it was installed from underneath. Is it possible to bolt on headers afterwards… meaning after the engine is installed??? Please clarify…
7:19 very important 😆
Guys where did you get the front brake dust sheild s from ??
Why would you run a cone style limited slip unit Auburn pro over say a Torsen style Eaton Truetrac?
@hiddenman99
3 жыл бұрын
FREE PARTS?
@narmale
3 жыл бұрын
wavetrac is even better :3
@larkm19
3 жыл бұрын
@@narmale more expensive too :)!
@narmale
3 жыл бұрын
@@larkm19 whats another 200 vs a whole new unit because the torsen granaded? i mean... :3
Good content nonetheless
All the stuff i couldnt afford. Adapted cobra brakes some 20+ years ago. Nice build though.
@trillrifaxegrindor4411
3 жыл бұрын
massive bucks thrown at this built,my friend at work has an 88 gt with 98% of these upgrades (running a cast iron 5.0 thats built)and its clean as a whistle
How much did all this cost and what car(s) could you have bought instead???
7:23 😂😂😂🤣😂🤣
Was there ever a part 3 to this so we can actually see the car in action?
Laser bobs would work well here
I just saw a picture of a solid axel with the title corner carver and I had to laugh.
@trillrifaxegrindor4411
3 жыл бұрын
you missed the triangulated 3 link and the coilovers,you tit
@aerickvesereu1796
3 жыл бұрын
@@trillrifaxegrindor4411 great so this the best cornering solid axle, that's like being the fastest morbidly obes person.
What do you guys do after building a car?...do you sell them?...or do you keep them for yourselves?
@gearbanginentertainment7476
3 жыл бұрын
sell them. i bought their 454ss featured on their Trucks! series
@ahnafzahid9450
3 жыл бұрын
@@gearbanginentertainment7476 454ci LS engine truck?...which truck model was that?...i forgot
@gearbanginentertainment7476
3 жыл бұрын
@@ahnafzahid9450 the truck is called a 454ss. search it up
Like every average blue collar schmuck such as myself has 50K laying around for a build like this....
@THRASHER1990
3 жыл бұрын
I guess I’ll just sell my house to fund my toy
@stevenchavez2003
3 жыл бұрын
Not at all once like them, but little by little, you can make it happen too
@trillrifaxegrindor4411
3 жыл бұрын
add 50% to that number easily....
7:23 nice
Sweet ride
No mention of a brake booster. I was curious.
like these nuts.. classic
Awesome car, they should of blasted the shock towers more, they rott there bad
K series shout-out at the end??
You guys should do a Honda K series build 😉
Like deez nuts… best one ☝️ ever 🤣
👍👍
I'd say, don't do this build without the total subframe package. I had a 89 4 cylinder that felt and sounded like it was going to fold in half going around backroad curves. What a pile of junk. Good times.
No rear IRS?
How much does this all cost
RPM Act!!!!
Did anyone else catch him pouncing on the torque wrench
Очень профессионально работаете. Приятно смотреть. Хочется подражать вам.
just wish it was a hatch
That is a lot of effort to not swap in a Cobra IRS which would've been cheaper and handled better over all.
@chrisvela5462
2 жыл бұрын
IRS would've needed some work from Kenny Brown
6:25 *Face Palm*
7:23
I've got $3000 in parts from maximum I've been waiting over 2 months on and they haven't answered my emails
Million dollar mustang
7:23 Deez nuts!
For corner carving those are too steep!
Get the government out of performance upgrades and racing
Some of these modifications don't seem to be planned originally. Some old fasteners and mounting spots don't look to have been cleaned up
4mm? I thought we still lived in America.
Why not put a 9 inch instead. Yeah I know it’s made for it.
Haha now it's got 87 iron suspension. Torque arms suck.
@mikeclement7780
3 жыл бұрын
Torque arms were used on the chevy monzas of the 70's.
@KrisKustomPaint
3 жыл бұрын
@@mikeclement7780 how did those drive? lol
@mikeclement7780
3 жыл бұрын
The one I had drove just fine with the sbc and th350 I put in it with no wheel hop when I got on it.
Audience, I have a donor drivable 1993 Fox GT if you guys would like to build on your channel. I'll even donate funds to assist with the build...🤜🏼🤛🏼🙌🏼.
Yes, and that brings up a Question. Where do you get the (NITROUS OXIDE) without a Prescription?
@RetroCheater81
3 жыл бұрын
Welding supply shops sometimes have it, or a speed shop.
@bertgrau9246
3 жыл бұрын
I bet summit racing would have the nitrous, but NOT for medical use
@kennedy67951
3 жыл бұрын
@@RetroCheater81 Yes I tried the Welding Supply and they said I needed a Prescription before I could buy the Gas. A bunch of Crap.
@kennedy67951
3 жыл бұрын
@@bertgrau9246 Well, Welding Suppliers here in Nashville said I had to get a prescription to buy the Gas. This why I asked the Question where to buy Nitrous Oxide without this bull crap Red Tape answers I'm getting from Suppliers.
You better at least do a drift after all this
LMFAO somewhere around 7:20 he said these nuts
😁👍✌👌🖖😎
Poor 2.3 lima we will miss your undustrectable reliability.
@trillrifaxegrindor4411
3 жыл бұрын
and slow as shit .bullshit
@brandonpurple8938
3 жыл бұрын
@@trillrifaxegrindor4411 what does slow have to do with anything ? Lol
Doing a wheel alignment without settling the tyres and suspension will end up with wrong settings , As your aligner said that'll do.
Deez nuts 🔩
Shabby mustang?
Pongan el vídeo en el canal de español por favor !!
Pl
A solid rear axle??? How primitive!
all that power and c clip axels, yikes.