Great review Eric. 👍. I went to harbor freight last week looking to order one. I was told maybe this spring. I realized the shipping/parts issue. I'll wait. Yours looks in great condition with the work you've done so far. I just maintain my vehicles. Thank you 👍👍

Thanks for the excellent report on your scissor lift!

@FarpointRestorationsAndRepairs

2 жыл бұрын

Thank you very much.

These reviews are very thorough, Erik. If I were a mechanic looking to purchase, I would have a great pro/con list. Stay safe and well.

@FarpointRestorationsAndRepairs

2 жыл бұрын

I appreciate that! If I were a one man mechanic show I would get one. This is fantastic.

I bought one from a lady who's husband passed away. Everyone says Harbour Freight stuff is cheap and made in China, so is bend pack and some others, they probably come the same factory. I am very satisfied with my lift, I have used it a lot, its a good investment.

@FarpointRestorationsAndRepairs

7 ай бұрын

I really think these are made by another company- I have been very happy with the one I have

@ohsoloco5113

6 ай бұрын

These don't even seem to be available any more. I should've bought one when I had the chance.

@buzzedalldrink9131

6 ай бұрын

just as long as it wasn’t the lift that killed the guy, you should be ok

Great Review 👍😎🍻

I watched a video of a guy that has the same lift as yours that is run on 120 volts. He has had no problem at all. He also put some heavy flat metal on his rear wheels on the lift. He used a 25 percent coupon and saved 400 bucks off. As you He has had no real problems and likes the lift. Thanks for the review. I would not be scared to buy one of these lifts. They will do what they are meant to do.

@FarpointRestorationsAndRepairs

Жыл бұрын

Thank you for sharing- I wish that I had gotten this years before I did- my back might be better off if I did.

Bought one about 6 years back and have used the hell out of it, my stepdaughters significant other can't even break it either. Sorry that boy given two steel balls and locked in a padded rubber cell in 30 minutes he will lose one and break the other, so you can say they are bullet-proof, he somehow got his Ram 1500 super cab, His Chevy Avalanche and didn't topple it over or break anything. Have used it to service and fab work, I even pulled the transmission and transfer case out of my 99 Jeep Wrangler with it, supprised the heck out of me, the rails worked fine with a small jack to hold things in place. Made a plywood deck to service snowmobiles, lawnowers etc..

@FarpointRestorationsAndRepairs

7 ай бұрын

had- I know the type to break stuff- I have thought about using the plywood for things like that to help save my back

@thomasheer825

7 ай бұрын

@@FarpointRestorationsAndRepairs Tried to use that approach, but he also uses the gas torches and welding equipment, lets just say that idea went up in smoke. They say you just can't fix stupid, well you can for $0.74, but you get the rest of your life free room and board at the cross bar hotel.

Nice review. Thank you for sharing this.

@FarpointRestorationsAndRepairs

2 ай бұрын

You're welcome

Nice scissor lift at a reasonable price. Thanks for the review/video.

@FarpointRestorationsAndRepairs

2 жыл бұрын

Thanks for watching!

Great review!

@FarpointRestorationsAndRepairs

3 ай бұрын

Thanks! I tired to make it as comprehensive as possible.

Plus all the aches and pain you’re saving your knees and back !! That’s worth the money right there !

@FarpointRestorationsAndRepairs

2 жыл бұрын

Maybe I would not have so many pains if I had bought this years ago.

Love the review,I'm going to look into getting one👍 ⭐⭐⭐⭐⭐

@FarpointRestorationsAndRepairs

10 ай бұрын

Hope you enjoy it!

Great review, appreciate it.

@FarpointRestorationsAndRepairs

Жыл бұрын

Thank you, I try to make some honest reviews that are helpful.

Great content. Thank you!

@FarpointRestorationsAndRepairs

Жыл бұрын

Glad You liked!

thanks for the video and your review. I almost bought it, but now its $2000 at harbor freight

@FarpointRestorationsAndRepairs

2 жыл бұрын

Ah yes, Hyper inflation. Come back in a year and we can talk about the good old days when this was only 2K.

I watched your earlier videos when researching my hoist. I decided to go for a similar mid rise scissor lift (in Australia). This has been such a handy addition to my workshop. I am planning to eventually cut the concrete floor and flush mount the lift and place a removable table top so the hoist will disappear when not in use (and just to make lower slung cars drive over easy). I would highly recommend these hoists, thank you for posting :)

@FarpointRestorationsAndRepairs

Жыл бұрын

Great idea! I'd love to do something like that here as well!

@cpzmelbs

3 ай бұрын

Where did you get it from with deliv to aus

@bleedingear1952

3 ай бұрын

@@cpzmelbs I got it through a company in W.A called AAQ

Oh man I love that lift! Bought mine about 4 years ago and it's been such a joy for an old man compared to laying on my back. With a low rolling shop seat you can back a vehicle up on it and you have full access to the engine. I use a tall jack stand under the front bumper for stabilization. Thanks for the review.

@FarpointRestorationsAndRepairs

Жыл бұрын

Right on! I have learned to love working on my cars while sitting.

@victorgutierrez5826

Жыл бұрын

could be a good idea if you share a video of your lifter with all the great words you said....i want ot see it in ACTION!!! because i plan to buy one of this lifters

Nice in depth review. When I worked at the dealership, they installed this type of scissor lift over 3 years ago. It was used every day as a full time service bay lift. No problems in over 3 years.

@FarpointRestorationsAndRepairs

2 жыл бұрын

Thanks for the info! Hope you are doing well

Nice follow up rewiew. This lift looks good for doing body work, brake jobs, wheel bearings. It looked a little scarry to me when you were underneath welding on a exhaust. The comment about the pump getting knocked over was good. Your pump was tucked in the corner so it would be unlikely get knocked over.

@FarpointRestorationsAndRepairs

3 ай бұрын

Right now I have my 72 VW Westy on it with no issues. It is still going strong- I think this is its 6th year owning it.

great review

@FarpointRestorationsAndRepairs

6 ай бұрын

Thank you

I’ve had one for 2 1/2 years. Total delivered after coupon was $1,399.06. Had a dozen vehicles on it up to a Suburban in weight. Works great. I put a heavy duty jack stand in middle underneath one of the pivot (scissor) points for extra safety.

@FarpointRestorationsAndRepairs

Жыл бұрын

Thanks for sharing, I have a new jack stand for the center if I need the extra support

With a solid top attacked, it would make a fantastic welding table. Being able to raise and lower your work as you're fabricating something is a huge boon! And it makes getting larger parts off the table a whole lot easier.

@FarpointRestorationsAndRepairs

5 ай бұрын

Great idea, anything that keeps me from having to bend over the better

I have had mine for 3yrs and all I can say it was probably one of my best tool investments. I have had full size pickups on it, Chargers, Jeeps and Numerous Vintage cars. It does its job very well. Extremely well made. Every vehicle is different and you have to make your lift arm adjustments. I make the lift to remember a specific vehicle. I built ramps so I can drive over it when it's not being used. I have kept a record of the money in labor I have saved by doing it myself with this lift and it has paid for itself 3 times over.

@FarpointRestorationsAndRepairs

Жыл бұрын

I agree with all that you have said, I kick myself for waiting to get mine. It is a game changer

I worked in a high end body shop and all they used was scissor lifts. After seeing all the different cars and trucks put on the lifts and all the tugging and on the vehicles to remove and install parts I can say that these are as safe as you can get having a vehicle in the air. If you are concerned about the strength of the design, look at a tractor trailer car carrier. The design and structure is the same. Though a car carrier looks to be dainty, it is capable of surviving millions of miles carrying maybe 15 to 20 tons of cars on our terrible potholed, bumpy off camber roads in all types of weather without failure. So a scissor lift stationary on a good concrete floor is living a rather stress free life in comparison. Trust the engineering cause it's big brother is a tractor trailer car carrier that brought you the car or truck you are currently driving. Enjoy.

I 've got an old scissor lift but got it out of a a friend dads shop lot you can find them from old tire shops or service stations mine was 100 bucks looked bad at first but with a little paint and grease worked fine I've left a 56 olds 4 door up on it for at lease 10 years to store stuff under it so anyway if you look around you my find one and save a little I've found 6or 7 more since I got mine so there out there

I agree, I'm sure they're all made in the same factory. I have the Danmar mid rise scissor lift and it's exactly the same as yours. I love mine also. My only regret is that I didn't get it sooner. I'm 52 and my knees aren't enjoying getting up and down anymore. Excellent review

@FarpointRestorationsAndRepairs

Жыл бұрын

I hear you on the knees! Mine are shot as well.

@rickhibdon11

2 ай бұрын

My Snap On scissor lift was made in CANADA

Great video Eric. I've had my lift for 2 years now and honestly cannot fault it. As you say many f these lifts were shipped from China, as mine was. I paid the same in £££ in 2020 and I'm happy with that.

@FarpointRestorationsAndRepairs

Жыл бұрын

Totally agree!

It lifts my cat eye silverado crew cab up with No problem at all for tire rotation, oil changes, changed the o ring on the oil pickup tube with this. Works awesome. Only problem is the arms are not wide enough for certain cars that dont have closer lifting points. Ive lifted a 95 honda civic, 2006 crewcab chevy silverado 4x4, 2004 mercury monterey minivan, 2012 chevy equinox, 2006 chevy trail blazer, 99 isuzu trooper and use it as a bench with a sheet of plywood for other random stuff. 5 years strong with no problems at all. Best $1000 I ever spent.

@FarpointRestorationsAndRepairs

Жыл бұрын

Thanks for your update! I too slap a piece of plywood on it for a make shift work bench at times.

I've had mine about 6 years. Best thing I've purchased in a long time. Only issue I've had was the pump filler neck came loose. Just cleaned it up and welded it so it wouldn't happen again.

@FarpointRestorationsAndRepairs

2 жыл бұрын

Thanks for sharing, I am glad to hear that yours is going strong after 6 years.

Love it !

@FarpointRestorationsAndRepairs

5 ай бұрын

They sell knock offs on eBay now. You will love them as much.

Neat rig never seen one of those before

@FarpointRestorationsAndRepairs

2 жыл бұрын

They have been around for a while now, I just wish I bought it years ago

Great review.... I always thought they were all 110volts. Never looked into them that much on that side. Love to get one at some point. Jack stands and ramps are not becoming as fun anymore....lol

@FarpointRestorationsAndRepairs

2 жыл бұрын

Glad I could help, I have found that I am slower to get up off the ground the older I get. This has been a life saver

i have the same lift, but from Eagle lift company - - bought it Aug, 1 , 2002 - - 31 yrs ago - for $1500 - - - - many, many side jobs later, made that $$ back several times over - -

@FarpointRestorationsAndRepairs

7 ай бұрын

They are really robust. It's now well into year 6 and this thing is holding up very well.

I have the Bend Pak 6000# lift from which this one was designed. Mine was made in '05, in the USA. I bought it used in 08 for $1200. It is the single best tool investment I have ever made. Mine is 110 volt. It only has three safety stops, more would be nicer. Mine is portable with the use of the pump/dolly combo. It's nice to roll out into the driveway for pressure washing under a car, etc. My shop has 9'4" ceilings, so a 2 or 4 post lift was out of the question. Most of my work up until fairly recently was vintage VW's, so there was never much need to access the middle of the car. Would be nice at times to be able to drop a trans in my toyota or chevy truck, but there are other ways to get that done. BTW, my 5000 pound Chevy has been on my hoist a few times with zero issues. Works perfectly. For everyday shop work, I built a plywood table that fits over the hoist. It is an instant work table, outfeed table for the saw, and a place to work on the lawn mowers, snowblowers, etc. No more kneeling on the ground to change the oil or a drive belt. Also works great for loading and unloading heavy things from my truck. Just back the truck up to the hoist, and lift the heavy thing to the same level and roll it in/out. For tires, brakes, suspension, oil/fluid changes and old VW repairs, there is nothing that will serve a guy better than a scissor lift.

@FarpointRestorationsAndRepairs

5 ай бұрын

Agreed. This thing is so handy and such a back saver, I wished I had bought it earlier. Love it!

had mine 7 yrs. now, no problems at all.

@FarpointRestorationsAndRepairs

Ай бұрын

That is about as long as I have had mine- Never had any issues,

I did all the research when looking for a lift. Called a concrete company because I ran into the same issue of not knowing what i was working with and what he told me was that he hasn't came across any residential pad that doesn't meet PSI requirements. Softer concrete is for decorative purposes and never used on driveways or foundations. Any concrete that meets residential requirements will hold a 2 post....BUUUUT, residential slabs are usually 2 1/2 to 3 inches thick in the center. The edges are usually thicker. Minimum requirement for a lift is 4 inches. I ended up pouring a 3 inch slab and setting down a movable 4 post lift. Now i'm looking for something more mobile to use in the driveway. This review definitely peaked my interest in one of these lifts! Thank you!

@FarpointRestorationsAndRepairs

6 ай бұрын

Glad I could help. This pad was poured by the previous homeowners and is questionable at best. I didn't want to risk my life on that question!

I bought this type of lift about 20 years ago. It looks the same as yours. I use the lift for years and I was getting hydraulic oil leaking past the internal seal on the top of cylinder and it would lock the cylinder from going up the other one would keep going up and the cylinder would come out of its seat. I would open the bleeder and it it would be ok. It never had the lifting power for heavier cars. So after 15 years of this I pulled the cylinder and took it apart and was going to get a new seal kit. What I found out was they installed the seal upside down on that cylinder. Seals were in good shape so I just turned it over and it was like two different lifts. Also i drilled 2 small holes in the upper pipe plugs. One was to let the air out better and also will let you know if your seals start leaking because oil will come out. I have worked on a lot of cars with this lift and it has been great. Wish I would have found that problem to begin with. I also mounted my pump to the wall and put a longer hydraulic hose with a quick disconnect at the pump.

@FarpointRestorationsAndRepairs

4 ай бұрын

That's crazy! We had something like that happen here at our house a few years back when I went to replace a toilet. Pulled it up and found that 20 plus years back someone had installed the seat flange 90 out. They then covered it up by using huge wood lag screws to hold the toilet down instead of a seat bolt. It turned a 30 minute job into a 90 minute one!

Hi, what a fantastic Video. Finally someone who really explains the advantages and disadvantages of this Scissor Lift. May I ask how tall you are. I am 1.92 m tall and have a back length of 1 m. I ask this because I see you sitting under the Car and think, could I also sit there under the Car. Or should I get down on my knees. I don't want this because I have 2 bad knees. Greetings from the Netherlands Akko

@FarpointRestorationsAndRepairs

10 ай бұрын

I am 6 foot 2 inches. No issues at all sitting under it.

@trabusas.3782

10 ай бұрын

@@FarpointRestorationsAndRepairs Thank you for your quick response, that gives me confidence that I can also buy one. 👍

Ps, I am a seasoned mechanic and use a lot of Harbor Freight tools. Every bit as good as the stuff you pay many times more than the name brand stuff. I realized I can fill my tool box with that same high quality tools using Harbor Freight stuff that are just as good as higher priced stuff I used to buy off the tool truck. Just my opinion.

@FarpointRestorationsAndRepairs

Жыл бұрын

your opinion is a good one, most people don't need a fancy name on a tool to get the job done. You can get 10 tools at HF for the cost of just one snap-on

Great review, Eric or Erik. I watched this video twice to capture data that I may have missed during my first viewing. I also viewed your 1 year review which after watching each video, I think I could now give the data and specs myself about lift. Hope you faired well during hurricane Ian. I'm down in Richlands, NC and we got quite a bit of rain and wind gusts but no severe damage nor did we lose power. Thank God for His grace. Alright my friend, I just wanted to give a shout and say hey and thank you for the reviews of the lift. You're right, you can't find the lift in the HF stores or in their on-line inventory but I'm sure if I asked them, they'd tell me how to acquire the lift. I'm also a NEW SUBSCRIBER to show support,👍🏽🤠 10/01/22

@FarpointRestorationsAndRepairs

Жыл бұрын

THANK YOU SIR!

The only thing that sucks about lifts like this is, it makes it nearly impossible to work on anything directly under the vehicle like exhaust, trans, floor, etc. Cool for outside of car work though, but pretty expensive for working on brakes or changing wheels/tires. Think I'll stick with my standard car jacks and jack stands. :)

@FarpointRestorationsAndRepairs

4 ай бұрын

Give it a few more years and you'll want this! My back and my knees no longer allow even a little floor jack work.

When I saw you had posted this Video, I was about to say ".. Erick, why do you keep teasing me with this, they are not available.." Then I read your the Video description with the link... So I apologize, for my initial snap judgment...

@FarpointRestorationsAndRepairs

2 жыл бұрын

They are back, and they are right where I thought they would be. 2K. Still not a bad deal in these days of hyper inflation.

I found a used Rotary inground lift..I restored..to new..oil tank is now above ground..no EPA issues.. per city .since it's tank is above ground..I've got a 10 ft ceiling..I can do most things on my hot rods ..as u can in your shop..

@FarpointRestorationsAndRepairs

Жыл бұрын

Thanks for sharing-

When u are welding u should cover the exposed shafts !

@FarpointRestorationsAndRepairs

2 жыл бұрын

Good point!

Question: on the Volvo XC70 (At 2:18), were you servicing the rear differential? Because I think that I need to do the angle bevel gear on mine. I'm getting a low noise grumble at 40mph. For all I know, it could be the tires.

@FarpointRestorationsAndRepairs

Ай бұрын

I don't think that you could get to the angle bevel gear, but you could get to the rear diff. Hope that helps

Everyone loves to bash HF but it’s great for regular people. Also remember some of those bad reviews could be bogus.

@FarpointRestorationsAndRepairs

6 ай бұрын

I love HF, I am thankful that there is not one near me as I would go broke

That sounds good. I work on a lot of Volkswagen... the real old bugs in buses...

@FarpointRestorationsAndRepairs

5 ай бұрын

I am working on a 72 Westy - converting to a Subaru engine

Definitely want to see the hydraulic schematic on one of these. I wouldn't trust a lift without counter balance valves.

@NoDoubtImPissed

Жыл бұрын

Haven't looked at any lifts. I'd hope they all have counter balance valves

@FarpointRestorationsAndRepairs

Жыл бұрын

I have no idea what they are like on the inside, but these lifts have been on the market since 2000. No one is dead yet!

What is the tubing size?

I like to wonder around harborfreight, everything went up price, and a lot of things are out of stock. These are going to $2k - thinking of financing it now - don’t want to fork of any cash right… thanks for the follow up videos.

@FarpointRestorationsAndRepairs

2 жыл бұрын

Good point, the price of everything is crazy now.

Great video, I just purchased a Triumph Scissor 6000lb lift. Built the ramps to drive up on for lower cars. I have lifted my Honda Pilot which is about 4300lbs. Do you use any of the the under lift stands to support the front and back of the vehicle while on the lift?

@FarpointRestorationsAndRepairs

6 ай бұрын

I have one , but the only time I use it is if I am pulling an engine.

Ever heard anybody using two of these each under front and rear wheels?

I have a ford focus awd and I need to pull the transmission to replace the slave cylinder. Transmission is to the left of the 4cylinder engine that sits sideways as all front wheel drive cars do. I believe I’ll need to unbolt and remove drive shaft and small transfer case to remove the gearbox. Do you think this lift will get the job done?

@FarpointRestorationsAndRepairs

5 ай бұрын

FWD? Yes, I've pulled transmissions. AWD? A bit more tricky. It would be tight but it's certainly possible.

Another good presentation. Do you run across any old fords for sale? lol

@Getusom

2 ай бұрын

Define old Ford?

Pls I want to this teach me some techniques in building lift ❤

very nice

@FarpointRestorationsAndRepairs

Жыл бұрын

Thanks, I should have bought one years before I actually did.

Question: sorry if you said 1. how high? 2. do they lock for safety reason if you under the lift.....3. could an engine be removed from the underside? thanks

@FarpointRestorationsAndRepairs

2 ай бұрын

1. 55 inches at full lift. 2, Yes there are 6 safety lock settings for various hights. 3, Yes. As shown in this video you can drop engines and transmissions from FWD and AWD cars.

Okay looking lift. What is the markings on the floor and, steel plates under the rollers? Thanks

@FarpointRestorationsAndRepairs

10 ай бұрын

My floor wasn't totally level.

@anhonestman1234

10 ай бұрын

@@FarpointRestorationsAndRepairs understood. Thanks for the reply

what about the thickness of the cement where is install it ? I think my drive way have 4inch thick also I see could be more safe if you can install about 2feet of pipe out ... on the side of the lifter to get more more stability of the lifter, overall I like it good review.

@FarpointRestorationsAndRepairs

Жыл бұрын

That amount of concrete is going to be just fine. As for the extensions, skip them. I know this lift looks like it would be iffy to operate, but 4 years on, I am telling you it's as sturdy and safe as any other lift I've used.

Nice review. Could i ask you a favour if you still have that? Could you take a measurement of the scissor arms? Planning on building something similiar

@FarpointRestorationsAndRepairs

Жыл бұрын

I'll see what I can do!

$1400 was a great deal! Now they are $2000. Have to wait on the 20% coupon.

@FarpointRestorationsAndRepairs

Жыл бұрын

inflation is crazy- who knows they might be $3k this time next year

@Kiddro22

Жыл бұрын

@@FarpointRestorationsAndRepairs They'll still be sitting in their warehouse if that happens if I'm concerned.

@billjacobs8035

Жыл бұрын

Coupon no good for lifts

@nmartin5551

Ай бұрын

They barely do those coupons these days. I miss them

@Tri-StarTurfSolutions

28 күн бұрын

@@FarpointRestorationsAndRepairsdoesn’t look like they even sell them now. Your link is dead and I can’t find one on their site by searching.

I think it's a good lift also and it's all how you use it

@FarpointRestorationsAndRepairs

2 жыл бұрын

I wish that I had gotten this lift years ago, it would have saved my back some pain

I can't find this lift in HF even with the provided link. I wonder if it pulled off of the shelves.

@FarpointRestorationsAndRepairs

Жыл бұрын

Keep the link and check back once a week. They only list it when they have units available to ship.

Hey Eric, are you able to put a car on the lift backwards ? to give you more room away from those lift hydraulic cylinders..

@FarpointRestorationsAndRepairs

Жыл бұрын

Yes, in fact some folks install them that way in the shop.

I use my similar commercial lift as a welding table which works a treat when you have a bad back. It does block underbody access but mine was only 500 barely used so I don't mind. I bought mine from a shop that never used it and replaced it with a two post which I will add to my shop (but keep the scissor lift). I would NOT pay over a grand new for one. Two-post lifts are not that hard to install.

@FarpointRestorationsAndRepairs

2 ай бұрын

I looked at a 2 post first, but I did not have the height to install one and did not want to pour new concrete for it to be safe. I like the idea of using it for a welding table.

Do you see any issues servicing differentials, transmission, oil, suspension, brakes, etc on a 2021 Sequoia 4WD, a 2019 Avalon Hybrid Limited, a 2011 Honda Odyssey, or a 2008 Toyota Solara?

@FarpointRestorationsAndRepairs

2 жыл бұрын

None at all. You can work around the scissors to access drain a fill points.

How would this work with the 1990s sw20 toyota mr2. Was thinking this would be great for my engine swap plans. Thanks

@FarpointRestorationsAndRepairs

Жыл бұрын

It should fit perfectly== good luck with your project

I have a Lift just like that one from Harbor freight I put the car on backwards and I got a lot more room under the car I can even service the transmission of a pick up truck keep that in mind my lift works great yeah yeah I got it for real cheap motor was wired backwards no pressure then I converted to 12 V battery and a cart and I can use that lift on my flatbed car hauler when we go to the race track or in the driveway or at my neighbors house put it right on my truck and take it across the street

@gtppower

Жыл бұрын

Hey Bob, so you had no issues putting the car on backwards ? have you done it multiple times ? thinking of doing the same

I have been looking at getting a similar lift , titan 6600 . I have also been looking at the stratus open center scissor lift . NOw that you have had this Lift for a while would you stay with that style or buy the open center lift . When im not using the lift it will be under my car and that’s the down fall for stratus . Hate having to drive over it when i wanna get my car out .

@FarpointRestorationsAndRepairs

5 ай бұрын

For the price, this one has been a great addition to the shop. If money was no object, It would be nice to have the open center, but honestly I can count on one hand how many times this has been an issue. You should also look on eBay as I see there are some off branded lifts that are identical to this one and cost about the same including shipping.

Has anyone made extensions for the pads to make then higher for trucks?

@FarpointRestorationsAndRepairs

2 жыл бұрын

Yes. I have a set from Atlas. Bend-pac also makes them, All three lifts are the same.

What's the heaviest vehicle you've had on the lift? I have a Suburban with a curb weight of 5800 lbs. and I just feel like the sheer size and girth of the Suburban would dwarf this lift.

@FarpointRestorationsAndRepairs

8 ай бұрын

I would be wary of that- The curb weight is too close to the limits--- I have had full sized trucks on this and it lifted them just fine

Does your lift wobble when it proceeds to the top most stop position?

@FarpointRestorationsAndRepairs

2 ай бұрын

It does a bit, that is normal. Even the 2 and 4 post lifts will do that

A great modification for these style lifts is to add 5000 psi quick disconnects to the hydraulic hose from the pump. I bought adapter fittings that screw into the junction block on the lift and the existing fitting on the end of the hose. The QD fittings then thread on to these adapter fittings

@FarpointRestorationsAndRepairs

7 ай бұрын

What is the advantage of that? Mine is a permanent install so What would that give me? Or is it just for people that move these units around a lot?

@truthboomertruthbomber5125

7 ай бұрын

@@FarpointRestorationsAndRepairs I guess for a permanent installation the hose never causes any issues with being in the way or having things dropped on it or rolled over it.

Love your Elvira poster

@FarpointRestorationsAndRepairs

8 ай бұрын

Thanks!

I just bought one of these, looks very similar, but the hydraulic pump, the electrical wires were just 3 bare ones, no 3 prong end. Not sure how i can power the pump.

@FarpointRestorationsAndRepairs

2 жыл бұрын

That sounds like a direct wire (hard wire)unit not one for an outlet

@_Wai_Wai_

2 жыл бұрын

@@FarpointRestorationsAndRepairs i actually just went to Lowes, and bought a power cable, with 3 prongs, and just joined the wires. The lift works, with a car on it.

Hello, I was at harbor freight website and could not find the scissor lift. How did you purchase yours?

@FarpointRestorationsAndRepairs

Жыл бұрын

It comes and goes from their website as it is available. They are having issues building them fast enough to compare with demand.

I just got a used one of these, one of the piston seals is blown and spits fluid out. Any idea where I can get a piston seal rebuild kit?

@FarpointRestorationsAndRepairs

2 жыл бұрын

While I don't know where to get the seals, I do know that you can order a replacement ram from Harbor Freight. There is also a thread on rebuilding the rams out there somewhere as I stumbled across it some time ago.

@genemulcahey9309

2 жыл бұрын

Good morning, yes Harbor freight still sells the complete cylinder assemblies for $165.00 each. Decent price. Just make sure when you ask for them you get both a left and right side, they are different. Its not listed as available but they are.@@FarpointRestorationsAndRepairs

@billjacobs8035

Жыл бұрын

McMaster-Carr has all of the components individually

28 days for concrete to get to full strength. Years of school and every dang test report I’ve ever read while building skyscrapers all were based on 28 day compressive strength

@FarpointRestorationsAndRepairs

2 ай бұрын

That is good to know- Thanks for sharing that

My Snap On scissor lift was made in CANADA

@FarpointRestorationsAndRepairs

2 ай бұрын

Great! But Snap-on hasn't made a lift like this since the 90's Craftsman tools were made in the USA back then too. Now? Bend-pac, atlas, and HF along with all the eBay knock offs are all made in the same plant in China.

Safety warning number 7 says do not work underneath unsupported?

@FarpointRestorationsAndRepairs

Жыл бұрын

By supported, they are talking about the lift lock. You never want to use the unit without lowering it onto one of the 7 lock positions.

@gavinoliver8074

Жыл бұрын

It actually says NEVER work under without additional safety devices (ie jack stands).

How mm the thickness of the material steel? thanks

@FarpointRestorationsAndRepairs

2 жыл бұрын

No idea. The lift is the same as the Atlas and bend-pac brands. Maybe their sites list that info? The lift is rated for over 6000lbs.

I have a saying there is nothing more permanent than a temporary fix

@FarpointRestorationsAndRepairs

Ай бұрын

Ha! Agreed!!

Looked for this lift at harbor freight.Doesnt look like it is available?

@FarpointRestorationsAndRepairs

Ай бұрын

It comes and goes- They just added it back to the site but shows unavailable- Before it was not on there at all

Where is the full version of your theme song and who sang it?

@FarpointRestorationsAndRepairs

2 жыл бұрын

it is on my main channel Farpoint farms, the singer is Marky Shaw- he has his own channel. You should check them out.

What is under the rear rollers?

@FarpointRestorationsAndRepairs

8 ай бұрын

My floor wasn't level so I added some metal for the rear wheels to ride on. I always planned on fixing the floor, but 5 years later, I figure it's still working fine so I'll stick with it.

I continue to search Harbor Freight for these and still nothing. So aggravating

@FarpointRestorationsAndRepairs

Жыл бұрын

they were sold out for a long time, then they were online only. I would keep checking every so ofter

@RusThompson

Жыл бұрын

@@FarpointRestorationsAndRepairs I will check again. Thanks!

As of November29, 2023 there is no listing for it on HF

@FarpointRestorationsAndRepairs

6 ай бұрын

They are however available under a variety of names on eBay. Search for "Mid-rise scissor lift".

I imagine dropping large fuel tanks is one of those things you might not be able to do with these?

@FarpointRestorationsAndRepairs

Ай бұрын

Agreed- there is too much stuff in the way to do that

Hard to understand. You say you watched other reviews on it prior to the purchase and how people said they are dangerous etc. Then why did you buy it ? And how much credit should interested buyers give to this review over the other reviews?

@FarpointRestorationsAndRepairs

6 ай бұрын

The "reviews" that claimed these were unsafe are from people that are not mechanics, and don't work in shops. Guess what? Standing under a car is scary. Everyday something can go wrong resulting in a loss of life. Sadly I've lived long enough to see both 2 and 4 post name brand lifts fail and one of those resulted in some major injuries. After 32 years turning wrenches under a variety of lifts, I can say that this style of lift is as safe as any other I've worked on including normal 2 and 4 post lifts. If you are afraid to work under this, I totally 10000% get it and I support your fears. Having 3000lbs over you is not all that fun, and if there was some sort of catastrophic failure you would get hurt. Look at Fukashimi. They built what they thought was a failsafe site, but nature has a way of screwing with all our best laid plans. I can say after spending 1000's of hours working under this lift and placing a lot of different cars on it that it's as safe as every other lift out there. I really hope this helps!

Does it have a safety lock?

@FarpointRestorationsAndRepairs

7 ай бұрын

It does have multiple locks.

Not even listed on the HF website anymore.

@FarpointRestorationsAndRepairs

Жыл бұрын

they were having supply chain issues not too long ago, I would just check back eery so often

My local HF has is at $1,999.99.

@FarpointRestorationsAndRepairs

2 жыл бұрын

They were out for the longest time, ,I am glad to see that they are back in stock.

Is this available now?

@FarpointRestorationsAndRepairs

8 ай бұрын

It comes and goes from their website. You can also get it under one of at least a dozen other name brands by googling "Mid rise scissor lift" I think eBay has them shipped for less than 2K.

Checked Harbor Freight’s website and still no scissor lifts 8/25/23

@FarpointRestorationsAndRepairs

8 ай бұрын

They are also available on eBay. Search for "mid-rise Scissor lift" and you'll see them for about the same price with shipping.

@BADD400

8 ай бұрын

@@FarpointRestorationsAndRepairs ok thanks

Hi sir, I have a question about my lift I believe we have the same lift. I bought mine about two years now and it didn’t have this problem. Just yesterday when I raised it up all the way up and on the right up gasket hydraulic liquid spray out from the small hole . I was little worried about it, I’d this something I should fix it and what I do to it? Do you have any suggestions or experiences with that problem. I’m great appreciate your help. Hoping to hear from you soon . Thank you

@FarpointRestorationsAndRepairs

Жыл бұрын

Oh no! Sorry to hear that, I've not had any issues with mine, but I would reach out to the Harbor Freight 1-800 number and get a new cylinder ordered before you have a injury!

@tubleejthoj6595

Жыл бұрын

@@FarpointRestorationsAndRepairs thanks

Has anyone ever lifted a catfish camaro with the factory lip kit?

@FarpointRestorationsAndRepairs

4 ай бұрын

Not this guy! Sorry I can't help.

I havent seen this lift for hf in years.

@FarpointRestorationsAndRepairs

7 ай бұрын

It comes back every year for a few months, but sells out nearly instantly. I think they just can't keep up with demand. Last time I spoke with them, they said they intended to keep selling them. They are also sold under a lot of other brands. Bend-pak, atlas, and some no name eBay units. All are made in the same factory with the same parts.

Will they lift a corvette

@FarpointRestorationsAndRepairs

Ай бұрын

I am not sure- they are pretty wide and fiberglass

I would pay 2 k for one !

@FarpointRestorationsAndRepairs

6 ай бұрын

It's a great tool! You can buy rebranded versions of these on eBay. Search for "Mid-rise scissor lift".

The hydraulic to frame of these just turns me off. I can't imagine lifting 6k with the angle the hydraulics pushes on that frame.

@FarpointRestorationsAndRepairs

9 ай бұрын

These have been in use professionally for literally decades. The design is as safe as any other setup. I've spent 1000's of hours (No exaggeration) working under this unit. 6 years later, no failures, no cracks, no leaks and no issues. It just works.