Босиком, без рукавиц, одна маска на сто человек! Вот это я понимаю!

@huseynrzayev9952

10 ай бұрын

Такова у них условия работы, ужасающая картина , мы от такого рабочего цеха сразу же убежали! Дай Бог им здоровья , счастья и удачи ! (это в Пакистане или же в Индии наверное )

@newportfamily7575

10 ай бұрын

Bugger you keyboard snow flakes,just think of what this team of gents could do with a little H@S and the correct tooling.

@newportfamily7575

10 ай бұрын

Cool

@vovasoltik3535

10 ай бұрын

техника безопасности на высоте, не слышали, а где она , нету а на хрен она нужна , итак сойдет.

@user-lq3bx9eq3o

10 ай бұрын

​@@huseynrzayev9952Пакистан

Сварщик в простых очках ваще бессмертный что ль 😊

@user-su2mj8xm3r

10 ай бұрын

... может и бессмертный но в розыске ! 🧐🤪

@DEMON23027

10 ай бұрын

Сварщик даже не смотрит что он там варит тыкает куда попало,😁😁,просто какой то пипец .

@user-pu6te9zk3g

10 ай бұрын

А почему сварщик в кроссовках а не в шлепках? Непорядок...

@mazai1026

10 ай бұрын

​@@user-pu6te9zk3g😂😂😂

@DEMON23027

10 ай бұрын

@@user-qy6rr4tu3y да ладно, а вы я так понимаю просто гуру сварки,мы тоже не лаптем щи хлебаем.Они как лепили горбатого так и продолжают.

Молодцы ребята! Без защиты, без техники безопасности, без маски, без хорошего инструмента... прицеп весит больше трактора наверное, учитывая сколько металла в нем. Прицеп без тормозов, нет смазки на пары трения, никаких гарантий... В перемотке как миньоны😅

Они в конце просто приварили ось к раме? типа 3000 использованных электродов недостаточно, болты отстой, вари дальше. Судя по толщине и количеству металла штука эта не сено возить будет, при всем уважении, но дорог у них нет, этож ось отвалится за поворотом!

@user-jg7lw9zt9k

10 ай бұрын

трактор медленно возит.. наверное только поэтому.

@raufjaleel8317

8 ай бұрын

троллейбус рассчитан только на одну поездку.😉

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

@user-wk6kw8bo7s

18 күн бұрын

Я для деревни варил прицепы. Один раз привезли прицеп заводской ступица вырвала все твои хвалебные 4 болта. Везли 3 бочки бензина. Заварил ездит 4 год возят по 3-4 бочки. Хотя я им сразу сказал с завода металл рассчитан на 400 кг.

I really would like to know the age some of these welders are before they become blind? They are great workers but deserve some decent protection!

@user-uw5uz9zu7h

9 ай бұрын

Eyrt8e37eutrwu

@JohnDoe-es5xh

9 ай бұрын

Seems that eye and foot protection is overrated at least in Pakistan.

@MrThisIsMeToo

9 ай бұрын

Calling them welders is a stertch.

@danieldestrada3029

9 ай бұрын

If there that stupid .so be it

@AbhiKabb-kn4ew

9 ай бұрын

)

всё чётко и качество, аккуратно без люфта как немце ,молодцы так держать👍👍👍

@user-du1uz5lf4p

6 ай бұрын

Так они могут собрать ка 52 верталет

@enricocarlassare5069

6 ай бұрын

🤣🤣🤣🤣@@user-du1uz5lf4p

Owner was like "OK guys, this week we are supposed to build a tractor trailer. Tools are here and in the warehouse you have some 6 tones of steel." Workers: "Yes."

@AKAtheA

9 ай бұрын

*6 tons of steel scrap :D

@selmirikanovic

9 ай бұрын

@@AKAtheA Yes, good point. The whole trailer was made out of literall scrap but may not be that bad thing since, as far as I know, most of metal available (per price) in Pakisatn, Bangladesh, Sri Lanka... comes from ship breakers that cut old ships and sell the metal. Since shipbuilding is quite regulated (it should be, I hope), steel quality should be relatively good (most of ships are built out of EN S355/ DIN St52-3 steel). The real issue is that, since they do not have metal available in standard dimensions (here in Europe steel beams in all forms are available in 6m (approx. 20 feet) or 12m (approx. 40 feet) they make beams for chasis by welding smaller pieces together to get to the desired length. Beam welding is not a bad thing (if done properly) but they definitely have way to many welds on main chasis and each weld zone is potentional crack zone. There are few design flaws / weak spots too. Connection between main chasis and axis is very weak for a trailer of this size, hinges connecting the lower and upper chasis are very weak too, lift mechanism is very crappy, movable parts with steel to steel contact under high load - it will wear in no time since there are also no lubrication/grease nipples.

@user-wx3mm8xy4v

6 ай бұрын

Туда только электродов тонна ушла

Ребята, берегите глаза, работайте в масках и защитных очках!!!! 🙏🙏🙏

@nightshadow5328

9 ай бұрын

бабы еще нарожают. они там как тараканы размножаются

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

подвеска,? не, не нужна, все равно мы больше 50 тонн не грузим, чтобы по серпантину с двумя прицепами разминаться удобно было.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Вот значит с кого "Миньонов" мультяшных срисовали! Рукастые мужики 👍

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Даже смотреть на это больно...

@raufjaleel8317

8 ай бұрын

Сделайте что-нибудь еще.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Сварщик, сварщик - парень настоящий! Сварщик, сварщик - электродов ящик! (с)

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

бахрома на бортах и какие то висюльки сзади это в пакистанских ПДД где то есть требования по установке?

I like their safety, welding glasses and foot Wear really good

@garazeprefabrykowaneproduc8263

5 ай бұрын

😂😂😂

@Skidderoperator

4 ай бұрын

Safety 1st👍

Тонн пятьдесят, надо полагать, в эту телегу точно навалят.

@georgyvahrushev3908

9 ай бұрын

Если эта телега по жизни будет стоять, а не ездить, то смысл в ней есть. А на ходу конечно разваливаться начнет. По виду тележка тонн на десять- пятнадцать.

@UlexPapov

9 ай бұрын

@@georgyvahrushev3908 у них электродов и ржавого металла дофига, будут регулярно чинить тележку. И все будут заняты. У всех будет немного хлеба для детей. Так и будут жить веками...

Подвеска,нет,не слышал 😢

@vovasoltik3535

10 ай бұрын

а что это такое...

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

@user-wk6kw8bo7s

18 күн бұрын

Если скорость до 30 км можно и бес подвески.

Как? Как, блть, эти чуваки в ночнушках стали ядерной державой, кто нибудь объяснит?😂

@bykvskijjevgenijj

10 ай бұрын

Советский союз помог

@Amiran_Ramalotti

5 ай бұрын

сша дал ядр пакистану а , СССР дал ядр Индии чтобы эти 2 армии в ночнушках не пересеклись..

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj

@user-wk6kw8bo7s

18 күн бұрын

Ты ещё русских не видел всем они стояли 60-80 лет назад. Это азы начало.

11:14 Вы не правильно делаете, надо перед работой снять защитный кожух с болгарки!

@vovasoltik3535

10 ай бұрын

100%

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Форма на заводе у них классная! Специальная, сварочная , халат - вон какой длинный... шлепанцы сварочные!

Not only did they build a chassis by welding three different pieces, but welded the trailer axle on it too.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

As long as it runs well on the roads and the company feeds families, well done 👏 but for ISO 9001 we'll see later please. it's a pleasure to see you at work, it's a change from those mega factory shows on the documentary channels.

@giorgiobassi9078

10 ай бұрын

Il. Concetto. E'. Giusto.... gran. Esperienza.....💪✋👍👀🇮🇹🇮🇹🇮🇹

@jemandjemand2362

10 ай бұрын

they dont even know what ISO 9001 means

@huseynrzayev9952

10 ай бұрын

l ıake you comment- bravo ! Thank you!!

@MDS6372

9 ай бұрын

​@@jemandjemand2362it's obviously standard Pakistan has so many companies working professionally in different sectors these are just street service providers across highways & heavy traffic roads to provide cheap work in immediate solution...

@raufjaleel8317

8 ай бұрын

​@@jemandjemand2362how come you jumped into this conclusion. They know ISO 9000,as well as, KAIZEN. The problem is those who have adopted these standards usually never allow these youtubers into their premises.

Быстро качественно ,,,,менеджеров нет

Ниче сё, ни одной заклёпки а только сварка 😮

Ассалаума-алейкум из Каракалпакстан ❤

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Those guys did an amazing job. Respect, my friends.

@Skidderoperator

2 ай бұрын

They can make furniture out of a pile of shit.

They'll overload it like they do everthing else !

@CJA150179

10 ай бұрын

It will be good for 30 ton that trailer..😆😆😆

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Kid with the glasses is going to go blind real quick

Подвеска вообще дикая!!!где рессоры?все что наварили отлетит при первой нагрузке и поездке по кочкам!😂

У сварщика в черном халате самая профессиональная сварочная маска , а так у них кто держак взял тот и сварщик !

@sergeygainullin5753

8 ай бұрын

Вероятно у него и халат из негорючки, в отличии от других

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj

I give you guys credit. You made that with a limited amount of tools and equipment. I would like to see you have better face shields for welding to protect your eyes from the arc flash. It also would have been better to add some brakes to the trailer for better stopping under a load, rather than relying on the truck towing it.

Mashallah, ما شاء الله

Pakistanis are serious metalwork guys ....

Очень много лишнего металла на раму потратили. И варят по очереди, что бы глаза не сильно портить. А те кто перетрудился, "отдыхают" пару дней в солнечных очках.

@user-zy1wt4uf7t

6 ай бұрын

Им виднее, куда и сколько металла нужно потратить

Admiratif de ces hommes et de leur travails dans des conditions moyenageuse dans la bonnes humeurs bravos

शानदार ट्रेक्टर ट्रॉली ,बेहतरीन डिजाइन very good

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

@organiced9805

2 ай бұрын

​@@user-le4ec6ii7d idiot spammer

Эти люди могут все в жазни!!! ❤

@user-jx4bn2iv7v

9 ай бұрын

Варить без сварочной маски! А вы попробуйте!

@Ctapx71

9 ай бұрын

@@user-jx4bn2iv7v я и говорю! Эти люди могут все! В молодости бывало варил без маски, теперь глаза болят...

@user-vz1wf1dv9e

4 ай бұрын

А ещё излучение от сварки рак кожи вызывает, как и при ядерном загаре!

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Когда-то это видимо был забор у кого-то.

@user-yh6dr9jn4x

10 ай бұрын

Телегу надо проваривать пол дня. Шоб не развалилась. 😅

@Bosjak63

10 ай бұрын

@@user-yh6dr9jn4x Это тебе не Автоваз , болты не забивают кувалдой ...

@user-yh6dr9jn4x

10 ай бұрын

@@Bosjak63 какой алковаз?

@user-pk1nu6hh3n

9 ай бұрын

Пакистан основная мировая разборка морских судов. Оттуда скорее всего б.у. металл

Fully automated production line! In Pakistan the meaning is, that as soon as one of these poor guys were injured or killed on the job, the next one immediately jumps in.

@raufjaleel8317

8 ай бұрын

Share with us your way of automated production........ Preferably on your channel.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

@horstmuller7512

2 ай бұрын

@@user-le4ec6ii7d That will probably happen in the next millennium. Priority is inventing chairs, tables, workbenches and, of course, toilet bowls.

Brilliant video thanks for sharing

Respect sir,,👍👍 love the way you People Are doing it

Sad about no safty but I love how they recycle. I always seem to come Home with more metal then I take to scrap yard for projects.

like on the beach, welding in sandals and sunglasses, i like it, only couple of cold drinks willbe needed

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Saludos al broder y al Chuchin! Echándole ganas como 100pre.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Ah takes me out to my back yard while welding …..The old thongs haha smell of burnt flesh and jumping all over the place ..got to take your hat of to these fellas …they work with what they have ..from outback Western Australia 👍👍

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

You know it's a quality build when the frame rails are scabbed to length

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

very impressed with their skill with what little they have, only thing not impressed with is the lack of grease fittings on the hinge points and pins...and not packing wheel bearings and lack of a grease cap for the hub allowing grit and dirt to enter the bearings.

@biggusdickus9046

6 ай бұрын

OH Dear.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

잘 보고 갑니다...^^

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

fanstastique ces ouvriers bravo et quelle qualité du travail bravo combien de familles vont se nourir de cette construction plus que nos robots j'espére qui eux font vivoter le boys et qui offre au gros plein de fric tout le bénéfice

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Vous êtes des génies de la construction métallique 💪🚚🙏🏽

@user-fc9go4dr4c

9 ай бұрын

\\

I’m speechless. They all have apple I phones yet are producing a death trap.

Muchas Felicidades Joven Por Su Canal. Saludos Cordiales Desde Mazatlán, Sinaloa, México. Remolques JJV NORTHSTAR

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

CRAFTSMAN AT ITS BEST, wish them luck and maybe some PPE wouldn’t hurt

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Now that everyone has a mobile phone, it might be an idea for people who make these videos to go on KZread to see what safety is. This can be safety glasses, hearing protection, gloves, safety on tools and not least safety shoes. KZread also has videos where people can learn how to tie shoes, then sandals can be replaced.

@adamsindler532

10 ай бұрын

Szerszámokbòl pont hogy a békebeli a jò! Nem pedig a dizájnos nagyáruházas vacak!

Got to watch these videos with my toes curled up lol

There is a looong way to precise machining... the one where straight lines, right angles and any predefined tolerance are important.

@Rimrock300

10 ай бұрын

and they're not going that way, as what they make seem to be 'good enough' for it's customers and price class

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj

Nice || safety first 😊

That dood with the face mask looks more western than the other workers or is he just in hiding or is he the big boss .

Geito simples de fabricar mais muito bem caprichado muitas fábricas do meu pais tem todos os equipamentos modernos mais não consegui fazer algo igual a eles kkkk

@user-iu5qt1xt8w

5 ай бұрын

В какой стране ты живёшь?

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Фиксики )))))

What do you do here? What. What do you do here? WHAT? WHAT DO YOU DO HERE? I DO ALL THE GRINDING. Why does that man keep walking into the walls? Ohh, he’s our welder.

Excellent well done I congrats 😂😂😂😂😂😂😂😂😂

Your workers will lose their vision and contract skin cancer if you do not provide them with eye and skin protection. I watched several workers suffer burns to their hands during the video! Get them welding gloves and aprons. I know they are expensiive, but you will have to train new workers when they go blind, are seriously burned, or die from skin cancer. It will cost you more to train new workers and slow your production than the cost of some personal protection equipment. Protecting your workers' health is cheaper than retraining workers to replace the dead or injured ones.

@harentrois

10 ай бұрын

It is not certain, the human is not taken into account in these countries, it is just a consumable that is replaced when it no longer works. It costs less to replace it than to equip it with protective equipment. and as for the training of new workers, seeing the quality of the work done, it's not super quality, but rather very basic, you just have to see the rust provided during construction, unthinkable in our factories or workshops.

@nathanscott7910

10 ай бұрын

@@harentroisthat's a sad reality in so many areas of the world. I watch alot of videos like this. You speak the truth about the lack of concern for human health and safety. It's crazy how many workers are barefoot or wearing sandals.

@sunny71169

10 ай бұрын

@@harentrois I agree with all except I wonder if your assesment that it costs less to replace a worker than to provide rudementary PPE is correct. In this setting It seems to me that it would cost more in lost production time to replace and train a worker than to provide him with a proper welding helment, welding gloves and leather apron and mandate long sleeved shirts. I understand work boots, or steel toed shoes and breathing apparatus are not happening. Those welders and helpers are blind men walking. One of them was staring into the arc as he was running the bead. The helpers were actually holding the work piece bare handed as it was being welded. Insane!

@horstmuller7512

10 ай бұрын

@@sunny71169 No wonder they have to curse their god minimum 10 times a day.

@raufjaleel8317

8 ай бұрын

​@@harentroisyou people have passed a very difficult time to reach present day status. Usually Western people hide their ugly faces. I saw old videos of their factories, people working in coal mines, chimney cleaning boys etc. Pathetic.

All the steel looks like ship super structure those people srap them make sense recycling

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj

I think the tail gate is the wrong side in. Wouldn't the smooth side go inside the box.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Always worries me when I see NO eye protection ie dark visors for the welders. some of them will be blind very soon!!

estos señores nos demuestran que la proteccion personal es solo un mito.. se encomiendan a su dios y eso es suficiente jajajaj

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Металева «тасьма» на цьому напівпричіпі це окремий вид мистецтва 😂😂 вага цього чуда певно 10 тон порожнім

@user-wx3mm8xy4v

6 ай бұрын

Да, без тесьмы не пройдет техосмотр

Parabéns..um trabalho muito bem feito

@24Dmitry

4 ай бұрын

Ни я йп

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

кто , среди этих уважаемых Господ , начальник ОТК ??

Мост приварили??)))) 😊

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

luar biasa dan terbaik saudara, salam dari indonesia 🇮🇩🇮🇳

@beatvario9570

9 ай бұрын

Pakistan itu bukan india

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

عماله شغاله بجهد في أعمال خطيرة بدون دسوس وأكثرهم بدون حماية لحام

Union workers like the highest quality product with osha approved methods.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

👏🏼👏🏼👏🏼👏🏼👏🏼👏🏼👏🏼👏🏼✨👊🏼🕶show!!!..Parabéns A EQUIPE!!..

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj

Солнцезащитные очки вместо сварочной маски?

It amazes me that this is speeded up but the workers look normal.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Маска,краги не нужны, , ботинки с защитой тоже.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj

Respekt für die Arbeit

@horstmuller7512

10 ай бұрын

Eine Mischung aus 12. und 19. Jahrhundert. Die meisten Arbeiter krepieren schon nach kurzer Zeit oder landen als blinde Bettler in der Gosse.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Wir sollten alle etwas Geld spenden und den Arbeitern ein Hallenkran spendieren

Там походу метал дешёвый)) 😂😊

@Bosjak63

10 ай бұрын

Сравни с Буханкой и удивись ...

@huseynrzayev9952

10 ай бұрын

Наверно из-за санкции Металлом Южный Порт продаёт им за клпейку 😀😀

@user-pk1nu6hh3n

9 ай бұрын

Пакистан из за дешёвой рабочей силы является основной мировой разборкой морских судов. Им ещё и деньги доплачивают за утилизацию. Оттуда и дешёвый б.у. металл.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj

Good work and good team.👍👍

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Fair play, made that with crude tools.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

the man in grey it's the 1st in india with semi DPI

Все с модными стрижками, и стильно выбритые, но сцк маски нормальной ни у кого нет..

@huseynrzayev9952

10 ай бұрын

Да.,тот молодой вообще без масок варит отворачивая голову в сторону, неужели все швы будут качественные или.он уже. по привычке варит --удивительно 😨

Good 👍

Все конечно хорошо но тежелая телега зазоры на заднем борту ,да и балка так неварется как минимум наискосок стык ,ещё бы им полуавтомат вообще было огонь а так уважение вашему труду

@aleksips2338

4 ай бұрын

Если им полуавтомат дать так они из и в Россию поставлять начнут 😂

نظارات حماية من اللحام جداً جدا جدا خطير

Прицеп без тормозов,но з красотой.

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

Esses caras vão dominar o mundo

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb

38:33 dude these tires look so flimsy😂😂

Nise😊

Kid welding with prescription glasses looking straight at the arc must not like his eyesight...

Супер 👍🔥

Смазки напихали красавчики, а что подшитник по сути снаружи остался, то похрену. И так сойдет. Уровень похуизма просто недостижимый.

Welding with sunglasses. The guy will be blind before long.

На 6.46 мастер йода нервно курит за углом

Tuti kényszerìtve vannak!

They dont even need to see if they are even welding the right part, they just burn the rod and hope for the best

اول مرة اشاهد عمال من الهند يعملون بالموسيقى ولا يرقصون 😂😂😂😂😂😂

@1MMMMM1

10 ай бұрын

یہ لوگ پاکستانی مزدور ہیں۔

@user-le4ec6ii7d

2 ай бұрын

I think that. 1. They should use better personal protective equipment: gloves, boots, welding helmet, leather apron and mask. 2. They should use stronger solder, type 7018, 9018, 11018. 3. They must make bevels for welding and leave space between the pieces (1/8) so that the pieces stick or adhere correctly. And even more so when it can only be welded on one side. 4. For very serious jobs like these, it is necessary to apply the welding vertically upwards. 5. For jobs as serious as these, it is necessary to apply the welding beads alternately: at one, at six 🕕, at nine 🕘, at three 🕒... At two 🕑, at seven 🕖.... 6. For jobs like these it is necessary to preheat the area where you are going to solder a little (60 degrees Celsius) 7. There is no need to bend the electrodes. 8. For jobs as delicate as these, it is better to apply the solder in letter (C) movements or in circles. 9. The entire piece should have some kind of tempering so that it does not bend so easily. 10. You can create a template or pattern to make the bevels with oxycut jjj hhjb jbjj

Almost went blind just to look at the video throu the screen