I just bought a GX555X 14 inch saw and just about have it set up. I too bought the 6 inch riser to give me more depth. that has to be put on yet. I will say that they are well made, quiet, and very little vibration. They are heavy to lift, so you will definitely need help to do that. I also got the carriage for mine, and it is well made too. I am well pleased so far with mine and feel that I got my monies worth on this purchase.
@PatCrowe9 жыл бұрын
I got one of these couple if weeks ago. Love it but I had a hard time adjusting the table to make it square to the blade. There is not enough room between the trunion and the table to get an open end wrench to tighten some of the 6 nuts. A 3/8" socket will work on some but not all nuts. I ended up buying a quarter inch 10mm socket and a flexible extension. This helps b/c the walls on the quarter inch socket are thinner than the 3/8.
@rauchfamily411 жыл бұрын
Thanks for the review Drew! I'm getting mine in a few weeks and I can tell you seeing yours all tricked out has me even more excited to get mine up and going. Thanks!
@seniorchiefharris9 жыл бұрын
Thanks Drew for your excellent review of the Grizzly 14" BS! I'm seriously considering purchasing one especially since the Anniversary Model is on sale (the same BS w/upgrades...). Great to hear that you're pleased with the BS and your review definitely helped me decide to purchase my new BS! Safe BS'ing and turning to you!
@hydmonger2816
3 жыл бұрын
Boy that was sure alot of BS right there 😂😂😂
@hydmonger28163 жыл бұрын
Love mine. Your review helped me in my decision to buy one.
@1badkota11 жыл бұрын
Yes mine was a tight fit, a few hits with a rubber mallet seated it properly. I figured it is supposed to be a tight fit in order to keep the proper alignment of the wheels.
@snapjamwoodworks7108 жыл бұрын
Great review!!! Any chance you could elaborate on the dust collection port you made? Pictures? Measurements? Thanks
@rva113 жыл бұрын
Great setup. Very nice work Sir. And thank you for the review.
@whitmore19786 жыл бұрын
Great review and I like the dust collection port as well as the brush brush. Grizzly doesn't offer a factory wheel brush on this model, so can you elaborate on yours? Did you get one from Rockler and make a bracket?
@henrysscrollsawworks63673 жыл бұрын
i asked a question but think added wrong number in my can i put a 2 hp motor for go555lanv the reason i ask the motor on it is not sutiable for resawing with any blade at least i found that with my saw its powerful enough when i try resaw its like trying to cut a chunk of steel even when i try put on higher speed so what do i need to do ive had trouble with this saw from day one
@dessertman11819 жыл бұрын
Nide review I.m looking to purchase my first band saw. I am just a weekend DYI person this may be a bit mote than what I need. Again well done!!
@TheScottie1040
6 жыл бұрын
Look into a Porter Cable from Lowes if you aren't needing this much saw. Same basic size at half the cost.
@Lorddarthvader17014 жыл бұрын
Great info video, I am going to buy this same saw. If you still have it do you still have the same opinion?
@joecachia130610 жыл бұрын
Hey Drew I like your dust port under the table. Do you have a video on how you made it or additional pictures? Joe
@sacasticus6 жыл бұрын
What mobile base did you get? Looking at the dimensions of the saw base from the website, I couldn't find a base that would fit.
@jeffoldham34663 жыл бұрын
i boought the rikon 10-326 about 2 yrs ago and i hated it,,,,i sold it yesterday and was considering this saw,,,can you tell me if you still have it and how well it performs,,especially on resawing
@douglasthompson27408 жыл бұрын
Nice labs. One owns me (110# Yellow, Mr. Duke). Got the same saw a couple of months after you did. Packaged it with the Grizzly G4003G 12" lathe. i have not been able to find any hose adapter to fit the factory dust pick up. It is a bit too big for all the 4" adapters that I have bought to try. Got a box of them now. Even the multistep ones do not fit. I would like to hook it to my shop vac. Seems Jet also makes that size outlet that no one makes an adapter for. The Jet dealer couldn't get one and none of the catalogs nor amazon have one that fits. What did you use for your hook up? I know what you mean on installing the riser kit by yourself! Even with a chain fall attached to the ceiling it was a huge handful to balance. I mounted it on a plywood base with casters which made the working height even better for me and formed the bottom shelf for storage. Thanks. Doug.
@lamarl9978
Жыл бұрын
Lowes or Home Depot has rubber plumbing adapters with a hose clamp. They work great have them on several of my tools.
@lyric.kayden4 жыл бұрын
Hi, do you have or experience any small vibration/shaking mainly in the top area when the saw is powering down?
@bnelson313braveheart8
3 жыл бұрын
I have on mine. I think it’s either due to my undeveloped floor and/or blade tension. Take a look at these areas to see if you can eliminate the noise.
@1956vern8 жыл бұрын
There very nice for the price!
@14wntr10 жыл бұрын
1/4" birch? are you sure you weren't over working it? :-)
@1badkota
10 жыл бұрын
yeah I need to upgrade so I can cut that mystical 1/2" ply haha
@smidefix81477 жыл бұрын
hello, are you still happy with the bandsaw?
@PhilReynolds9 жыл бұрын
Did you buy the Shop Fox mobile base? If so how did you get the lock nuts started on the bolts. I can only get 2 of the 16 started. Just doesn't seem like it should be that hard. Thanks for any advice.
@1badkota
9 жыл бұрын
I don't remember mine being very difficult to assemble. Is it possible the threads on yours were damaged?
@PatCrowe
9 жыл бұрын
Phil Reynolds I have an extension that chucks up in my drill. The end that fits in the drill is the hex like you have with a screwdriver bit, the other end is a 3/8" square socket drive (square fitting). I held the hex bolt head steady with a pair of vice grips and drove the lock nut onto the bolt with the drill. Wasn't easy, but it worked. Best wishes.
@PhilReynolds
9 жыл бұрын
Thanks. I ultimately got it but it was very difficult. All is good now though.
@BillyBlaze75 жыл бұрын
not quite moving the camera enough...
@brickskinner11 жыл бұрын
I think your dogs want out.
@chilldog123456789010 жыл бұрын
how heavy is it?
@TheScottie1040
6 жыл бұрын
About 250 pounds shipping weight more or less.
@Psyko10011 жыл бұрын
i see you have a shipping pallet leaning against the door. if you build things for me i can supply you with an endless supply of pallets.
@acemany11263 жыл бұрын
Nice and we'll oil made in China machine 👍
@BYYoseph4 жыл бұрын
6:04 damn if that piece he cut off doesn't look like a finger lol made me cringe just a bit.
Пікірлер: 36
I just bought a GX555X 14 inch saw and just about have it set up. I too bought the 6 inch riser to give me more depth. that has to be put on yet. I will say that they are well made, quiet, and very little vibration. They are heavy to lift, so you will definitely need help to do that. I also got the carriage for mine, and it is well made too. I am well pleased so far with mine and feel that I got my monies worth on this purchase.
I got one of these couple if weeks ago. Love it but I had a hard time adjusting the table to make it square to the blade. There is not enough room between the trunion and the table to get an open end wrench to tighten some of the 6 nuts. A 3/8" socket will work on some but not all nuts. I ended up buying a quarter inch 10mm socket and a flexible extension. This helps b/c the walls on the quarter inch socket are thinner than the 3/8.
Thanks for the review Drew! I'm getting mine in a few weeks and I can tell you seeing yours all tricked out has me even more excited to get mine up and going. Thanks!
Thanks Drew for your excellent review of the Grizzly 14" BS! I'm seriously considering purchasing one especially since the Anniversary Model is on sale (the same BS w/upgrades...). Great to hear that you're pleased with the BS and your review definitely helped me decide to purchase my new BS! Safe BS'ing and turning to you!
@hydmonger2816
3 жыл бұрын
Boy that was sure alot of BS right there 😂😂😂
Love mine. Your review helped me in my decision to buy one.
Yes mine was a tight fit, a few hits with a rubber mallet seated it properly. I figured it is supposed to be a tight fit in order to keep the proper alignment of the wheels.
Great review!!! Any chance you could elaborate on the dust collection port you made? Pictures? Measurements? Thanks
Great setup. Very nice work Sir. And thank you for the review.
Great review and I like the dust collection port as well as the brush brush. Grizzly doesn't offer a factory wheel brush on this model, so can you elaborate on yours? Did you get one from Rockler and make a bracket?
i asked a question but think added wrong number in my can i put a 2 hp motor for go555lanv the reason i ask the motor on it is not sutiable for resawing with any blade at least i found that with my saw its powerful enough when i try resaw its like trying to cut a chunk of steel even when i try put on higher speed so what do i need to do ive had trouble with this saw from day one
Nide review I.m looking to purchase my first band saw. I am just a weekend DYI person this may be a bit mote than what I need. Again well done!!
@TheScottie1040
6 жыл бұрын
Look into a Porter Cable from Lowes if you aren't needing this much saw. Same basic size at half the cost.
Great info video, I am going to buy this same saw. If you still have it do you still have the same opinion?
Hey Drew I like your dust port under the table. Do you have a video on how you made it or additional pictures? Joe
What mobile base did you get? Looking at the dimensions of the saw base from the website, I couldn't find a base that would fit.
i boought the rikon 10-326 about 2 yrs ago and i hated it,,,,i sold it yesterday and was considering this saw,,,can you tell me if you still have it and how well it performs,,especially on resawing
Nice labs. One owns me (110# Yellow, Mr. Duke). Got the same saw a couple of months after you did. Packaged it with the Grizzly G4003G 12" lathe. i have not been able to find any hose adapter to fit the factory dust pick up. It is a bit too big for all the 4" adapters that I have bought to try. Got a box of them now. Even the multistep ones do not fit. I would like to hook it to my shop vac. Seems Jet also makes that size outlet that no one makes an adapter for. The Jet dealer couldn't get one and none of the catalogs nor amazon have one that fits. What did you use for your hook up? I know what you mean on installing the riser kit by yourself! Even with a chain fall attached to the ceiling it was a huge handful to balance. I mounted it on a plywood base with casters which made the working height even better for me and formed the bottom shelf for storage. Thanks. Doug.
@lamarl9978
Жыл бұрын
Lowes or Home Depot has rubber plumbing adapters with a hose clamp. They work great have them on several of my tools.
Hi, do you have or experience any small vibration/shaking mainly in the top area when the saw is powering down?
@bnelson313braveheart8
3 жыл бұрын
I have on mine. I think it’s either due to my undeveloped floor and/or blade tension. Take a look at these areas to see if you can eliminate the noise.
There very nice for the price!
1/4" birch? are you sure you weren't over working it? :-)
@1badkota
10 жыл бұрын
yeah I need to upgrade so I can cut that mystical 1/2" ply haha
hello, are you still happy with the bandsaw?
Did you buy the Shop Fox mobile base? If so how did you get the lock nuts started on the bolts. I can only get 2 of the 16 started. Just doesn't seem like it should be that hard. Thanks for any advice.
@1badkota
9 жыл бұрын
I don't remember mine being very difficult to assemble. Is it possible the threads on yours were damaged?
@PatCrowe
9 жыл бұрын
Phil Reynolds I have an extension that chucks up in my drill. The end that fits in the drill is the hex like you have with a screwdriver bit, the other end is a 3/8" square socket drive (square fitting). I held the hex bolt head steady with a pair of vice grips and drove the lock nut onto the bolt with the drill. Wasn't easy, but it worked. Best wishes.
@PhilReynolds
9 жыл бұрын
Thanks. I ultimately got it but it was very difficult. All is good now though.
not quite moving the camera enough...
I think your dogs want out.
how heavy is it?
@TheScottie1040
6 жыл бұрын
About 250 pounds shipping weight more or less.
i see you have a shipping pallet leaning against the door. if you build things for me i can supply you with an endless supply of pallets.
Nice and we'll oil made in China machine 👍
6:04 damn if that piece he cut off doesn't look like a finger lol made me cringe just a bit.