Continued work on 1977 Wanderlodge FC with 3208 Naturally Aspirated engine.
Жүктеу.....
Пікірлер: 21
@fernandomeneses4412 жыл бұрын
Hey Man, Thats great, a good job. I'm from Brazil, today I worked in a CAT 3208 apply in a waterpump of supermarket . thanks for share your experience.
@0505abab4 ай бұрын
Great video I have one of those tubes leaking I have a new pump now I need to find someone to install it in a motorhome
@0505abab
4 ай бұрын
I've been reading my book on it I think you make it look easier than it is but still well done
@Dominolittle11 ай бұрын
Great share. 😊
@henrygerrets8199 Жыл бұрын
Great video, thanks
@bryandailey4174 Жыл бұрын
Thanks for the video - working through this on my bird.
@GinosGarageUSA
Жыл бұрын
Thanks, I am following along on the WOG.
@hydromakers Жыл бұрын
Got to pull one off nest week Just taking a refresher coarse.Thanks
@timeparmenter48163 жыл бұрын
Another fine video and fix.
@GinosGarageUSA
3 жыл бұрын
Thanks for watching Tim. Hope things are good for you and the family!
@chrishuelskoetter6475Ай бұрын
I need help please with finding the puller and bolts needed to pull that front timing gear off, with the 2 little bolts.
@GinosGarageUSA
Ай бұрын
There are a couple different tools that can be used for this. This is a possible option, but cannot say for sure it will work but it’s not too expensive: a.co/d/9jVef4e You may need to get bolts but they are standard 1/4”x20tpi bolts that you can get from any hardware store. I would recommend grade 5 or better. This is the tool that I have: www.apexinds.com/tools/M10070.html?gclid=CjwKCAjwgdayBhBQEiwAXhMxtkzytxrjqQRx8xHBU_vEnn2DxPZEqf7DMdpuQ7TeMiUYuE21a0K7cBoCJFUQAvD_BwE
@jeremiahcarney93912 күн бұрын
Is the pump timing pin anything special or did you just find something that fit
@GinosGarageUSA
11 күн бұрын
There is a special tool for the job but you can use a 1/4” drill bit or any 1/4” round stock for the pin.
@CanadianPenguin_ Жыл бұрын
that pump manages to look massive and tiny at the same time. how long and wide is that pump?
@GinosGarageUSA
Жыл бұрын
I can tell you they are quite heavy. I would say they are approximately 12" x 12"
@hrios802 жыл бұрын
Where did you find that gear pulled to separate the pump ?
@GinosGarageUSA
2 жыл бұрын
Check out eBay: rover.ebay.com/rover/0/0/99?loc=https%3A%2F%2Fwww.ebay.com%2Fp%2F1133979573
Пікірлер: 21
Hey Man, Thats great, a good job. I'm from Brazil, today I worked in a CAT 3208 apply in a waterpump of supermarket . thanks for share your experience.
Great video I have one of those tubes leaking I have a new pump now I need to find someone to install it in a motorhome
@0505abab
4 ай бұрын
I've been reading my book on it I think you make it look easier than it is but still well done
Great share. 😊
Great video, thanks
Thanks for the video - working through this on my bird.
@GinosGarageUSA
Жыл бұрын
Thanks, I am following along on the WOG.
Got to pull one off nest week Just taking a refresher coarse.Thanks
Another fine video and fix.
@GinosGarageUSA
3 жыл бұрын
Thanks for watching Tim. Hope things are good for you and the family!
I need help please with finding the puller and bolts needed to pull that front timing gear off, with the 2 little bolts.
@GinosGarageUSA
Ай бұрын
There are a couple different tools that can be used for this. This is a possible option, but cannot say for sure it will work but it’s not too expensive: a.co/d/9jVef4e You may need to get bolts but they are standard 1/4”x20tpi bolts that you can get from any hardware store. I would recommend grade 5 or better. This is the tool that I have: www.apexinds.com/tools/M10070.html?gclid=CjwKCAjwgdayBhBQEiwAXhMxtkzytxrjqQRx8xHBU_vEnn2DxPZEqf7DMdpuQ7TeMiUYuE21a0K7cBoCJFUQAvD_BwE
Is the pump timing pin anything special or did you just find something that fit
@GinosGarageUSA
11 күн бұрын
There is a special tool for the job but you can use a 1/4” drill bit or any 1/4” round stock for the pin.
that pump manages to look massive and tiny at the same time. how long and wide is that pump?
@GinosGarageUSA
Жыл бұрын
I can tell you they are quite heavy. I would say they are approximately 12" x 12"
Where did you find that gear pulled to separate the pump ?
@GinosGarageUSA
2 жыл бұрын
Check out eBay: rover.ebay.com/rover/0/0/99?loc=https%3A%2F%2Fwww.ebay.com%2Fp%2F1133979573
What is the valve clearance in millimeters?
@GinosGarageUSA
2 жыл бұрын
Intake is 0.38mm and exhaust is 0.64mm.
@micko7927
2 жыл бұрын
Thanks mate👍