G90E budget dent puller and other dent repair tips!
Жүктеу.....
Пікірлер: 56
@kseries20-24only Жыл бұрын
This dude is the dent master! Least amount of mud used for sure 😎
@GarageNoise
Жыл бұрын
👍Thank's brother!
@nestormoran2812 Жыл бұрын
Chris, you do such a nice job massaging the metal that it looks good enough to fill with just filler primer! Your videos always motivate me to go out and work on my own projects. Thanks!
@GarageNoise
Жыл бұрын
Awesome! Honestly, the support I get inspires me to produce better more in depth content! So I really appreciate your comment!
@chriscoesbodyshop Жыл бұрын
Great video! I have the same machine and it works great. I have never used to shrink metal, I’ll try that out also, thanks. I added a magnet to my ground so it stays in the correct area.
@GarageNoise
Жыл бұрын
👍appreciate the support, I had a magnetic ground and it fell apart.I need to order another.
@jamesward5721 Жыл бұрын
Been working a lot on improving my skills at using heat to lift dents - I use glue-pulling (mechanical) & a spotter all the time, but last couple weeks I've been experimenting with using a map gas torch & an airline. With a little practice, the results you can get with just those 2 tools is pretty impressive. It's the absolute ideal technique for repairing oil-canning & even very deep dents you would never imagine would lift using heat. Gist - well my "Version" is you heat the periphery of the dent lightly, then focus the flame right in the middle for 4-5 seconds, then blast the center with the air blow-gun. You will see massive "lift" immediately as the steel shrinks. From there it's just dialling in your technique until you can approach even the bigger dents with confidence & get them back to a flat & taught panel using just this technique. I've repaired some pretty gnarly stuff using just the gas-torch & airline - once you get proficient at this technique, it can do some amazing stuff without having any access to the backside of the damage.
@GarageNoise
Жыл бұрын
Good stuff! I most used heat shrinking if I have a problem with stretched metal. I'm intrested in the skills you're developing sound worth investing! Appreciate the comment and support!
@jamesward5721
Жыл бұрын
@@GarageNoise Man, it never "Clicked" in my head till I had a customers car in last week with a deep dent I couldn't get to the back of - I started wondering "What if?" - and damn, it worked. Heat & air - I only tried it as heat & water were getting on my nerves wetting up my nice clean floor. Air works better.
@jamesward5721
Жыл бұрын
@@GarageNoise Love the Channel - always learning stuff from you. Happy to share some stuff I learnt to reciprocate. One hand washes the other. Bodywork pays our bills, so if i'm doing it, it works. :-)
@GarageNoise
Жыл бұрын
@@jamesward5721 👍
@GarageNoise
Жыл бұрын
@@jamesward5721 Now I have used heat for aluminum, the dent pops out even small ones you can even do it without damaging paint sometimes. Too hot and it will melt it tho.
@JohnWD40TC02 Жыл бұрын
Amazing work as always Chris, I love watching you do these repairs as you make it look so easy but I know it isn't as you see people replace a panel like this rather than fixing it which is such a waste👏👍John UK
@GarageNoise
Жыл бұрын
Wow, thank you! Appreciate the comment and support!
@DanielSan-ch7dr
3 ай бұрын
Get them cheap once thrown out or get one from a wrecker at substantial diacount and sell for full price after paint and repair then your profot on parts will increase making your labour bill look less. People seem to be happy to pay the parts cost but not the skill to paint and install it properly.
@shugg0517 Жыл бұрын
Chris i love your channel . Brought myself a 2012 Dodge Charger RT back in January with a blown engine . Needs a little bodywork , especially on both fenders. The repairs needed are in the same spot as the new video you just released. Thanks for all you do .
@GarageNoise
Жыл бұрын
Perfect timing! Appreciate the comment and your support of the channel!
@nelsonramos2218 Жыл бұрын
I love the channel, you have been a great help with my projects, awesome tool!! Thank you sir
@GarageNoise
Жыл бұрын
Appreciate the comment! Thank's for your support!
@TonysRefinishingTV Жыл бұрын
POPPED OVER AFTER YOUR COMMENT THE OTHER DAY FELLA GREAT CHANNEL AND VIDEOS BUD
@GarageNoise
Жыл бұрын
Appreciate that! I've seen your channel before haven't really had a good chance to check it out but I'm a subscriber . I just noticed that video on getting hacked, what a scary deal. Appreciate the kind words brother keep up the good work!
@dennissedillo4148 Жыл бұрын
Chris you do really good work. Good video to learn from
@GarageNoise
Жыл бұрын
Thank's Dennis appreciate the support!
@Snip59 Жыл бұрын
Excellent video from start to finish cheers.
@GarageNoise
Жыл бұрын
Thank's for the comment! Appreciate the support!
@Daidwei3 ай бұрын
Good machine and skilled master.
@GarageNoise
3 ай бұрын
Thanks 👍
@Daidwei
2 ай бұрын
@@GarageNoise U know what? I am the producer of this product (from the other half of the planet), I came across your video, I was very surprised, but you operate very well, because the machine is one thing, your operation skills are more critical.
@88Painterman Жыл бұрын
Great video as always!
@GarageNoise
Жыл бұрын
👊👍Thank you!
@guillaumel364011 сағат бұрын
Hey Chris, I ended up purchasing this a few months ago and I love it. I’ve done a few jobs with it and it’s worked like a charm, until I got asked to fix a hood that was made of aluminum lol. Any tips on how to make the G90e work properly on aluminum?
@josue62888 ай бұрын
Quick question, is there any precautionary steps to take before welding onto a vehicle such as disconnecting the battery? I’m afraid I might fry a module or pop some fuses. Thanks
@GarageNoise
8 ай бұрын
As a precaution, I like to disconnect battery.
@tedc9306 Жыл бұрын
Appreciate if u would demo a shrink video. Ty
@GarageNoise
Жыл бұрын
👍👊
@Bekind19803 ай бұрын
I have one cant get it to stick anuff to get a good pull
@AnDre-tq1xr Жыл бұрын
How do you pull out dents on aluminum panels?
@dustykamphuis5444 Жыл бұрын
Great video!! Do you think this machine would pull out dents in older vehicles with thicker guage steel?
@mohamedkasririfi84446 ай бұрын
بدون أزلت بطارية السيارة
@AliVapeReviews Жыл бұрын
Where do you buy more of the stubs the triangle ones and others for it just bought a g90e used but didn’t come with any but one
@mtuhro3 ай бұрын
I am considering the G90e for my home shop. In one of the original videos you had swapped out the ground provided with the tool with a magnetic ground. In this video it looks like you went back to the original ground. What made you decide to go back?
@GarageNoise
3 ай бұрын
The other one broke. I have a new one now I like very much.amzn.to/3ycJlTS
@mtuhro
3 ай бұрын
My g90 arrived. I am liking it for fine tuning, after using glue tabs for the bigger pulls. I think any of the negative reviews are people expecting too much out of it. Keep up the good work.
@afrikagreen6303 Жыл бұрын
will this machine do aluminum body?
@GarageNoise
Жыл бұрын
No it will not.
@afrikagreen6303
Жыл бұрын
@@GarageNoisethanks for reply,,,,
@jumpinjojo Жыл бұрын
Chris, would it have been faster and therefore less expensive to have obtained a used fender?
@GarageNoise
Жыл бұрын
It was close, but when replacing the fender you have the additional cost of blending into the door and hood plus removing all the trim associated with those panels.
@jumpinjojo
Жыл бұрын
@@GarageNoise That’s true. Now you only have to blend into the existing fender. Thanks, Chris!
@dardenvern Жыл бұрын
What is the cost of a repair like this typically?
@GarageNoise
Жыл бұрын
About a 4 hr dent . 180 to remove dent
@impalaman4546 Жыл бұрын
👍👍💯
@GarageNoise
Жыл бұрын
👍👊👊
@kirkwesterveltoutdoors Жыл бұрын
This weekend I painted a fender that I had repaired. I blocked out the high build primer to 600gr. The repair looked good. I decided to spray an epoxy sealer first before laying down the base coat. The sealer must have been not thinned down enough or the air pressure was wrong. The sealer came out thick and had orange peel. I only spray the repair area. I should have stopped, however I layer down the base and clear. Now I can see the orange peel under the base. What would you do to correct this issue. Thank you for your time Sir
@GarageNoise
Жыл бұрын
It's hard to say without seeing it. I would try to wet sand and buff if your not happy after that then scuff with 600 and base and clear it again. Hope this helps appreciate the support!
@kirkwesterveltoutdoors
Жыл бұрын
I think you are right, that is the answer. Block the clear flat then the base will lay flat, then clear again. I can see that now. It is going to get warmer starting next week. I will prep and get ready. Thank you, that helped.
Пікірлер: 56
This dude is the dent master! Least amount of mud used for sure 😎
@GarageNoise
Жыл бұрын
👍Thank's brother!
Chris, you do such a nice job massaging the metal that it looks good enough to fill with just filler primer! Your videos always motivate me to go out and work on my own projects. Thanks!
@GarageNoise
Жыл бұрын
Awesome! Honestly, the support I get inspires me to produce better more in depth content! So I really appreciate your comment!
Great video! I have the same machine and it works great. I have never used to shrink metal, I’ll try that out also, thanks. I added a magnet to my ground so it stays in the correct area.
@GarageNoise
Жыл бұрын
👍appreciate the support, I had a magnetic ground and it fell apart.I need to order another.
Been working a lot on improving my skills at using heat to lift dents - I use glue-pulling (mechanical) & a spotter all the time, but last couple weeks I've been experimenting with using a map gas torch & an airline. With a little practice, the results you can get with just those 2 tools is pretty impressive. It's the absolute ideal technique for repairing oil-canning & even very deep dents you would never imagine would lift using heat. Gist - well my "Version" is you heat the periphery of the dent lightly, then focus the flame right in the middle for 4-5 seconds, then blast the center with the air blow-gun. You will see massive "lift" immediately as the steel shrinks. From there it's just dialling in your technique until you can approach even the bigger dents with confidence & get them back to a flat & taught panel using just this technique. I've repaired some pretty gnarly stuff using just the gas-torch & airline - once you get proficient at this technique, it can do some amazing stuff without having any access to the backside of the damage.
@GarageNoise
Жыл бұрын
Good stuff! I most used heat shrinking if I have a problem with stretched metal. I'm intrested in the skills you're developing sound worth investing! Appreciate the comment and support!
@jamesward5721
Жыл бұрын
@@GarageNoise Man, it never "Clicked" in my head till I had a customers car in last week with a deep dent I couldn't get to the back of - I started wondering "What if?" - and damn, it worked. Heat & air - I only tried it as heat & water were getting on my nerves wetting up my nice clean floor. Air works better.
@jamesward5721
Жыл бұрын
@@GarageNoise Love the Channel - always learning stuff from you. Happy to share some stuff I learnt to reciprocate. One hand washes the other. Bodywork pays our bills, so if i'm doing it, it works. :-)
@GarageNoise
Жыл бұрын
@@jamesward5721 👍
@GarageNoise
Жыл бұрын
@@jamesward5721 Now I have used heat for aluminum, the dent pops out even small ones you can even do it without damaging paint sometimes. Too hot and it will melt it tho.
Amazing work as always Chris, I love watching you do these repairs as you make it look so easy but I know it isn't as you see people replace a panel like this rather than fixing it which is such a waste👏👍John UK
@GarageNoise
Жыл бұрын
Wow, thank you! Appreciate the comment and support!
@DanielSan-ch7dr
3 ай бұрын
Get them cheap once thrown out or get one from a wrecker at substantial diacount and sell for full price after paint and repair then your profot on parts will increase making your labour bill look less. People seem to be happy to pay the parts cost but not the skill to paint and install it properly.
Chris i love your channel . Brought myself a 2012 Dodge Charger RT back in January with a blown engine . Needs a little bodywork , especially on both fenders. The repairs needed are in the same spot as the new video you just released. Thanks for all you do .
@GarageNoise
Жыл бұрын
Perfect timing! Appreciate the comment and your support of the channel!
I love the channel, you have been a great help with my projects, awesome tool!! Thank you sir
@GarageNoise
Жыл бұрын
Appreciate the comment! Thank's for your support!
POPPED OVER AFTER YOUR COMMENT THE OTHER DAY FELLA GREAT CHANNEL AND VIDEOS BUD
@GarageNoise
Жыл бұрын
Appreciate that! I've seen your channel before haven't really had a good chance to check it out but I'm a subscriber . I just noticed that video on getting hacked, what a scary deal. Appreciate the kind words brother keep up the good work!
Chris you do really good work. Good video to learn from
@GarageNoise
Жыл бұрын
Thank's Dennis appreciate the support!
Excellent video from start to finish cheers.
@GarageNoise
Жыл бұрын
Thank's for the comment! Appreciate the support!
Good machine and skilled master.
@GarageNoise
3 ай бұрын
Thanks 👍
@Daidwei
2 ай бұрын
@@GarageNoise U know what? I am the producer of this product (from the other half of the planet), I came across your video, I was very surprised, but you operate very well, because the machine is one thing, your operation skills are more critical.
Great video as always!
@GarageNoise
Жыл бұрын
👊👍Thank you!
Hey Chris, I ended up purchasing this a few months ago and I love it. I’ve done a few jobs with it and it’s worked like a charm, until I got asked to fix a hood that was made of aluminum lol. Any tips on how to make the G90e work properly on aluminum?
Quick question, is there any precautionary steps to take before welding onto a vehicle such as disconnecting the battery? I’m afraid I might fry a module or pop some fuses. Thanks
@GarageNoise
8 ай бұрын
As a precaution, I like to disconnect battery.
Appreciate if u would demo a shrink video. Ty
@GarageNoise
Жыл бұрын
👍👊
I have one cant get it to stick anuff to get a good pull
How do you pull out dents on aluminum panels?
Great video!! Do you think this machine would pull out dents in older vehicles with thicker guage steel?
بدون أزلت بطارية السيارة
Where do you buy more of the stubs the triangle ones and others for it just bought a g90e used but didn’t come with any but one
I am considering the G90e for my home shop. In one of the original videos you had swapped out the ground provided with the tool with a magnetic ground. In this video it looks like you went back to the original ground. What made you decide to go back?
@GarageNoise
3 ай бұрын
The other one broke. I have a new one now I like very much.amzn.to/3ycJlTS
@mtuhro
3 ай бұрын
My g90 arrived. I am liking it for fine tuning, after using glue tabs for the bigger pulls. I think any of the negative reviews are people expecting too much out of it. Keep up the good work.
will this machine do aluminum body?
@GarageNoise
Жыл бұрын
No it will not.
@afrikagreen6303
Жыл бұрын
@@GarageNoisethanks for reply,,,,
Chris, would it have been faster and therefore less expensive to have obtained a used fender?
@GarageNoise
Жыл бұрын
It was close, but when replacing the fender you have the additional cost of blending into the door and hood plus removing all the trim associated with those panels.
@jumpinjojo
Жыл бұрын
@@GarageNoise That’s true. Now you only have to blend into the existing fender. Thanks, Chris!
What is the cost of a repair like this typically?
@GarageNoise
Жыл бұрын
About a 4 hr dent . 180 to remove dent
👍👍💯
@GarageNoise
Жыл бұрын
👍👊👊
This weekend I painted a fender that I had repaired. I blocked out the high build primer to 600gr. The repair looked good. I decided to spray an epoxy sealer first before laying down the base coat. The sealer must have been not thinned down enough or the air pressure was wrong. The sealer came out thick and had orange peel. I only spray the repair area. I should have stopped, however I layer down the base and clear. Now I can see the orange peel under the base. What would you do to correct this issue. Thank you for your time Sir
@GarageNoise
Жыл бұрын
It's hard to say without seeing it. I would try to wet sand and buff if your not happy after that then scuff with 600 and base and clear it again. Hope this helps appreciate the support!
@kirkwesterveltoutdoors
Жыл бұрын
I think you are right, that is the answer. Block the clear flat then the base will lay flat, then clear again. I can see that now. It is going to get warmer starting next week. I will prep and get ready. Thank you, that helped.