G35 Coupe HALO tail lights part 1
Автокөліктер мен көлік құралдары
Follow along with this tutorial and learn how to install halo LED's in your G35 tail lights. This method works with '03-'05 coupe tail lights. It has not been tested with '06-'07, however it should work the same in theory. There is a lot of risk involved in this DIY, and I highly recommend finding
an extra pair of tail lights to try this on before cutting open your only pair.
If you have any tips on how to improve this method be sure to drop a comment.
Part 2 available here: • G35 Coupe HALO tail li...
Below is a list of tools and materials you'll need to get started. Additional tools may be necessary.
Tools, parts and materials:
Gloves (Mechanix and latex)
G35 coupe tail lights
LED halo rings, 90mm and 110mm (bit.ly/qasimhalo)
Flat tip screwdriver
Phillips head screwdriver
Ratcheting wrench with 8mm deep socket
Wrench, 8mm
Acrylic knife (bit.ly/acrylicknife)
Hot knife OR dremel with plastic cutting disk
Drill with 7/64 bit
Alcohol wipes
Surface to paint on (ie cardboard)
Clear storage container
Primer
Spray paint
Fishing line
Super glue
Butyl headlight sealer (amzn.to/33eDOY8)
Soldering iron kit (amzn.to/2no47vs)
Rosin core solder
Wire strippers
Heat shrink
Various clamps
Diode Dynamics Tail-as-Turn (optional)
----------------------------------------------------------
All Music by LAKEY INSPIRED.
Track 1 - Better Days
Track 2 - I Found Me
Track 3 - The Process
Track 4 - Good Morning
Track 5 - Warm Nights
Official Soundcloud: / lakeyinspired
License for commercial use: Creative Commons Attribution 3.0 Unported "Share Alike" (CC BY-SA 3.0) License.
creativecommons.org/licenses/...
Пікірлер: 38
I will try this, thanks brother
Love that you mentioned not to mess with the ridge on the lens when you remove it. I saw a guy pick at it and when he resealed it, he didn’t have a a nice perimeter line. It was all choppy with black spots
Молодец, хорошоя работа 👍
Wish you made more videos
You made this look super easy, ever done anyone else’s taillights? And how much would you charge?
@calynhutto6424
3 жыл бұрын
Hello mate, just read your message -
@calynhutto6424
3 жыл бұрын
I do offer this as a service, prices start at 275 for send in tail lights and 600 for a brand new set with halos.
@hudcu
3 жыл бұрын
@@calynhutto6424 how do i contact you about this?
@calynhutto6424
3 жыл бұрын
@@hudcu I no longer offer this service. My apologies.
Can't you use the oven method for the tail lights as you do on the headlights??
@SV6SPD
2 жыл бұрын
No they are plastic welded so you have to use a dremel to cut the housings
Great vid.What size was the halos?
@calynhutto6424
3 жыл бұрын
90mm on the small, 110mm on the large. I would do 85mm on the small if you can find it.
What hot knife is that
How close to the lense did you get? Some parts of the housing have thinner areas than others. Thanks
So what if I don't paint it in black? And leave chrome?
U think I can do this to a g37
@calynhutto6424
3 жыл бұрын
More than likely, I've never tried though. I think it's a similar method, probably just different size rings
Quick question but what kinda of paint did you use to paint the bezel ?
@calynhutto6424
4 жыл бұрын
13:48 I went with Rustoleum engine enamel. It left a really glossy finish, looking back I would have went with something a bit more satin. Really any paint should work fine, I would avoid cheaper stuff as it might chip later down the line
@vq_suaaa4378
4 жыл бұрын
Thanks bro and what’s your @ bro
@calynhutto6424
4 жыл бұрын
@@vq_suaaa4378 @fcasn_hutto
Hey guys, I didn't mention this at the time of upload but depending on the LED rings you purchase you may have issues seeing the brakes or turn signals in the day time or direct sunlight, which is a safety issue. To remedy this, I recommend either purchasing higher quality LED's than I did (Diode Dynamics and Profile by Morimoto both make LED's that are visible in sunlight) OR leaving the turn signal and OEM brake light LED's intact when performing this mod.
@matthewsanmiguel8599
4 жыл бұрын
Calyn Hutto did you get red or white halos ?
@calynhutto6424
4 жыл бұрын
@@matthewsanmiguel8599 I used white halos, however I recommend getting the red ones. They will be brighter in the tail light housing.
@sapboi104
4 жыл бұрын
Either way great video,you was very precise,I would love to have you do mine
@sapboi104
4 жыл бұрын
And I'll pay you
@calynhutto6424
4 жыл бұрын
@@sapboi104 Hey there much appreciated! I just saw your comment, if you're serious about getting your tail lights done you can message me over on insta, @fcasn_hutto. Thanks!
Where can I get the aperture
@calynhutto6424
3 жыл бұрын
If you are referring to the halo rings, I purchased the ones on video from Amazon however I now use Diode Dynamics halos for all of my installations
@carlossaravia9201
3 жыл бұрын
@@calynhutto6424 halo sizes from diode dynamics?
@calynhutto6424
3 жыл бұрын
@@carlossaravia9201 110mm for the large circle, 85mm or 90mm for the small circle. 90mm provides a very tight fit.
@carlossaravia9201
3 жыл бұрын
@@calynhutto6424 thank you
Did you use a white halo or red halo?
@calynhutto6424
3 жыл бұрын
I used white but I highly recommend using Diode Dynamics red halos in 90mm and 110mm. You can use an 85mm as well for the smaller circle, I've found 90mm fits tight and requires some force to get into place.
@carlossaravia9201
3 жыл бұрын
@@calynhutto6424 thanks alot bro
whats your insta?