Full Depth Asphalt Recycling Overview
Ғылым және технология
An overview of the Full Depth Asphalt Recycling process in the province of New Brunswick by Maritime road recycling (Northern Group). under contract to The New Brunswick Department of transportation and Infrastructure.
Rte # 630, 3 & 4, Contract # 16-0116, McAdam, New Brunswick, FDR, Base and Seal.
Locate the area on Google Earth and drive it with "Street View" before the project with the following Coords. Location: 45°39'21.74"N, 67° 7'53.21"W
Equipment:
Wirtgen WR2500 Pulverizer
Wirtgen WR3800 Mill
CAT 140H Grader
Emulsion Trailer
Water Trailer
International 10000 liter water truck
Live Bottom Trailer and Aztec Buggy
Vogel Paver 2100
Dynapac Breakdown Roller
CAT Rubber tire roller
CAT Finish Roller
Produced by Lindsay Carr, DTI
www.gnb.ca/0113/
Thanks to: Northern Construction Group: northerngroupco.com/
Пікірлер: 34
Ran milling machine 32 yrs and seeing this one run backwards is new to me
@Ober447
5 жыл бұрын
Its made to be run in both forward and reverse. When it runs this way it uses a down cut which provides finer material and less loss on the screening plant for recycling. Your machine is a up cut and much faster than this operation and is used for straight milling. Your machine tends to provide more loss at the screen than the down cut. The upper cut tends to pick-up alligator cracking and delaminations without breaking the material very fine so it becomes loss at the screen.
I really like that water truck that's in the very beginning of the video.
I saw a machine (German?) demonstrated online that shaves off the old asphalt, processes it and lays it down. All that is left is to use a roller and let it cure (in short time).
Damn, that black truck was hauling ass, came close to that worker. Only one roller used?
@Ober447
9 ай бұрын
No, three rollers. same as you would use for hotmix
who thought it was a good idea to hang a coat on your precision leveling bar... did it throw off the cross slope any, or did it compensate for it ?
That gold on the wirtgen is sweet
With Pulverizer do u repave after?
@Ober447
7 жыл бұрын
Yes, one lift of base asphalt and one lift of seal asphalt.
Interesting
What percent water are you typicallyy running on the train ?
@Ober447
7 жыл бұрын
The mix contains around 3% water. This % varies with the material but generally it runs around 3 %.
@raysabin1820
7 жыл бұрын
Thank you ! That"s about what I generally run 1-3 %
Just curious...why is the third roller used when there will be a final mat of asphalt covering everything? Does your rubber tire leave any waves along it’s finished surface or will there be a good stretch of time before final/top mat? In Northwestern Ontario on my job sites we had a 50 ton breakdown followed by a 20 ton rubber tire on both base mat and final. HL4 mix.(virgin base..no reclaim) Inspection was completely sufficient. Oh and that machine ‘propelling’ the trailer hopper, is that an old converted steel roller?..it’s hard to see in the phone picture.
@Ober447
5 жыл бұрын
We use three rollers for maximizing compaction because as you are aware your hotmix overlay compaction cannot exceed the base compaction values. The breakdown roller here is approximately a 25 ton (half the curb weight of your 50 tonner) so the last roller is required for compaction. The finish roller does also remove the rubber tire marks as you mentioned. The storage trailer is being hauled by an old Roadtec steel wheeled Aztec Paver (screed and hopper removed) converted to haul the trailer to save money
Accidentally got here by adding another zero to my search.
What's the fuel burn per hour operating the entire train?
over 2 years later hows it holding up?
@Ober447
9 ай бұрын
I got crack seal down the center joint last summer and has very little reflective cracking which is where this process shines.
Pulverizer rotfl its called a road/soil reclaimer
i want the second in line tanker truck drivers job
You really don’t need sound with this piece, just the narration, imho.
🤡dumb question. does the milling machine propel the whole outfit along?
@Ober447
7 жыл бұрын
The Milling machine pushes the two tankers only, the rest of the gear is self propelled.
A
Bom dia! Pra mim é uma honra viu prestigiar seu trabalho, vamos sempre juntos somar e fortalecer nossos objetivos, Conto com você, eu já estou por aqui.,,.
front right tyre needs air
Stop using the metric terms we don't use that in the USA.
@hawkboy000
3 жыл бұрын
Is it that hard to use both? Sheesh😬
@lilbender7408
2 жыл бұрын
Yall the only one not using it LEARN IT CLOWN
@joelhenderson5404
2 жыл бұрын
@@lilbender7408 yall are the clowns still driving on the wrong side.