Replacing bearing and seal on a Ford tractor PTO Shaft Assembly
Жүктеу.....
Пікірлер: 11
@stephaniewilley2224 Жыл бұрын
There's something both startling and satisfying to me about that "bang" noise when the press first breaks the hold of the bearing or gear on a shaft. Back in the "old days" before the Montreal Protocol I would have warmed the new bearing and retainer ring on the shop's coffee maker heat pad and placed the end of the shaft in a small inexpensive Styrofoam cooler into which I emptied a small can of R-12 refrigerant. After just a few minutes the bearing and retainer would fall rather loosely into place on the shaft. No pressing, no hammering. The temperature of the heated bearing was well within the tolerance, even the normal operating range and the temp of the cooled shaft was only a few degrees colder than it might have experienced in one of our Michigan winters. This was also my preferred method in that time for setting timing gears onto crankshafts. Certainly that old method is unthinkable today.
@chickenhousemechanic
Жыл бұрын
Yeah that works for sure. Dont think the EPA would be happy about using R-12 like that though.
@stephaniewilley2224
Жыл бұрын
@@chickenhousemechanic most definitely a method NOT approved today.
@cjenkins95 Жыл бұрын
I replaced my pto after it broke on my 850 now the pto will not disengage any ideas
@chickenhousemechanic
Жыл бұрын
Depending on where it broke your pto shifter may be damaged. You can remove the side cover that the pto shifter is on and see how everything moves. You might find something broken as well.
@philliphall5198 Жыл бұрын
I’ve had great luck with Steiner seals for pto even if it is warn a little
@bubblesandbows1 Жыл бұрын
can you tell me where I could find parts for y 1910
@chickenhousemechanic
Жыл бұрын
Never looked for parts for one of those but I've heard they're hard to come by. Best place might be a new holland dealer. I've bought parts from New holland for my 4000 and 861 through Messick's Tractor Parts. Yesterdays tractors also has a few parts for those models.
@MegaPs3killer7 ай бұрын
Would you consider selling your old SOS PTO shaft? Mine is scored due to the bushing going out.
@chickenhousemechanic
7 ай бұрын
Sorry I no longer have the pto shaft from the sos.
Пікірлер: 11
There's something both startling and satisfying to me about that "bang" noise when the press first breaks the hold of the bearing or gear on a shaft. Back in the "old days" before the Montreal Protocol I would have warmed the new bearing and retainer ring on the shop's coffee maker heat pad and placed the end of the shaft in a small inexpensive Styrofoam cooler into which I emptied a small can of R-12 refrigerant. After just a few minutes the bearing and retainer would fall rather loosely into place on the shaft. No pressing, no hammering. The temperature of the heated bearing was well within the tolerance, even the normal operating range and the temp of the cooled shaft was only a few degrees colder than it might have experienced in one of our Michigan winters. This was also my preferred method in that time for setting timing gears onto crankshafts. Certainly that old method is unthinkable today.
@chickenhousemechanic
Жыл бұрын
Yeah that works for sure. Dont think the EPA would be happy about using R-12 like that though.
@stephaniewilley2224
Жыл бұрын
@@chickenhousemechanic most definitely a method NOT approved today.
I replaced my pto after it broke on my 850 now the pto will not disengage any ideas
@chickenhousemechanic
Жыл бұрын
Depending on where it broke your pto shifter may be damaged. You can remove the side cover that the pto shifter is on and see how everything moves. You might find something broken as well.
I’ve had great luck with Steiner seals for pto even if it is warn a little
can you tell me where I could find parts for y 1910
@chickenhousemechanic
Жыл бұрын
Never looked for parts for one of those but I've heard they're hard to come by. Best place might be a new holland dealer. I've bought parts from New holland for my 4000 and 861 through Messick's Tractor Parts. Yesterdays tractors also has a few parts for those models.
Would you consider selling your old SOS PTO shaft? Mine is scored due to the bushing going out.
@chickenhousemechanic
7 ай бұрын
Sorry I no longer have the pto shaft from the sos.
@MegaPs3killer
6 ай бұрын
dang, thanks tho!@@chickenhousemechanic