I just bought a Ford 641 and I was curious on how to get the pto shaft out. Good video thank you looking forward to see part 2

Great clip. I especially loved the part where you prepared us for the dropping of the shaft into the sand. I'll try to remember that when I remove mine for the first time lol.

Informative, quick and to the point. Great video. Thanks.

Chief, if you have a New Holland dealership near by, you can get parts for any of the old Ford tractors from them. New Holland bought the agriculture equipment division of Ford years ago and they still supply parts for them.

@billeaglerunner6844

7 жыл бұрын

Thanks I got the right part yesterday.

Hey Bill!I just today replaced my PTO seal and a word to the wise put a large tub under the PTO shaft to catch fluid. I elevated the rear of my Ford 3000 but it was not enough, guess what happened. You can not put the shaft back in quickly, no way. So once out disassembly was easy after removing the retaining clip. Long end up just drop the PTO shaft down on a piece of wood and the housing comes right off the bearing pretty easy. The replacement seal you got that looks different is good to go just looks different, same part number. The side with the seal spring goes to the inside. The seal removal and installation tools work great to remove and install the seal. Remove the seal from the inside out and install from the outside in. To reinstall the shaft I used a piece of PVC over the output end to get the leverage needed to fit the long end inside. With the PVC pipe over the output side it went in on the second try. Without the PVC pipe for leverage I bet it was a real pain in the rear to get the splines to line up. Easy peasy lemon squeeze Bill thanks for your video. :)

@billeaglerunner6844

7 жыл бұрын

Great! maybe I should have used a piece of PVC. But It wasn't too hard to slide it in. Thanks for the info "Easy peasy lemon squeeze". I like it. Thx for watching.

What yr is that tractor?? if u don’t mind.

Bill, you sound like John Wayne.....

I am not sure where you are in Florida. If you are near Ocala, you can try Ocala Tractor LLC. I think they are a New Holland dealership. I hope this helps.

@billeaglerunner6844

7 жыл бұрын

Thanks I got the right part yesterday.

We have an older model 160 Allis Chalmers, there apparently weren't too many of these around. The PTO shaft seal is leaking and we want to change it but don't want to start until we maybe can get some advice from someone who has done this before. My hubby is retired and spent his life in the mechanical field so will be able to follow the instructions okay. If you have any advice or ideas we would be glad to read them. Thanks in advance.

@billeaglerunner6844

6 жыл бұрын

I am new to old tractor repair. Don't take what I do as instruction it's meant to be entertainment.. I am not a professional. What I do is my best guess on how to do it. There is so little information on old tractor repair. I post these videos showing how I did the job. I am not sure if I am doing it wrong or Right? But someone might get something of value from the video. Thank you and thx for watching.

@norahcurl5004

6 жыл бұрын

Thanks, ours is a bit different than the Ford as it seems, according to the schematic, we will have to split the tractor to remove a nut and gear to allow us to pull the shaft out the rear. If you do hear of anything that might help with our Allis Chalmers Model 160 we will be glad to get your into. Norah

@phillipwilson3848

5 жыл бұрын

Ford 40000 clutch pto

@pardonmasvikeni7194

5 жыл бұрын

Ůyy

Eaglerunner, did you have to pull the PTO selector cover on the side of the tractor ,

@billeaglerunner6844

7 жыл бұрын

No. I did engage the PTO before I removed the PTO shaft, and tied the handle to make sure it stayed engaged. Thanks for watching.

Great video. Thanks

quiero saver sobre sistema hidrulico del ford 300p y 4000

great speaking voice

@SisterSmith420Peace

4 жыл бұрын

Sadly he has passed away

@N8Catona

4 жыл бұрын

@@SisterSmith420Peace dang.

I broke the PTO shaft on my tractor. Trying to figure out what year it is so I can order the right replacement. My tractor looks completely identical to yours. What year is your's? Can't seem to locate a SN on the thing. thanks

@SisterSmith420Peace

4 жыл бұрын

He passed away. Sadly

@douglascarkuff1969

4 жыл бұрын

@@SisterSmith420Peace So sorry to hear.

@ricktarded5943

4 жыл бұрын

I finally found someone to follow and lost them just as quick? I am so sorry for your loss. My condolences.

@SisterSmith420Peace

4 жыл бұрын

@@ricktarded5943 he was a friend that I play pool with he was a nice guy he made some good videos sad to see him gone thank you for your condolences

Como cambiar la flecha delgada que va en el tractor Ford 6610 que es para la toma de fuerza

You don't have to remove anything but the seal to replace it.

The first thing I would do is remove my Rolex befor working on the tractor.

@douglascarkuff1969

4 жыл бұрын

I'd sell the Rolex and buy a nice, new John Deere.

That's not a shim sir, it's a gasket and you need to get a new one or it will leak, they are cheap, just sayin.

I make that shaft....tell me if anybody want that....

needle nose to remove the retaining ring huh? Not as easy as you say. I would have loved to see on video you using needle nose pliers to remove that snap ring. I spent an hour fiddle farting trying to get that dang thing out. I ended up taking the shaft and new seal to a local implement dealer and had them change the seal for me. Folks its harder to remove that snap ring than you realize. Good luck

@krstoner53

Жыл бұрын

I have took a cheap HF extra large pair of needle nose with the 90 degree handle and ground down the tips just enough to be able to remove large 3 or 4” internal style snap rings