Great video for independence day. %99 of guys I know that drive truck couldn't run a lathe to save their life. You're at the top of your industry.

@rearspeaker6364

2 күн бұрын

60% are steering wheel holders!

@garymessina1609

2 күн бұрын

Well it turned out great just a lot of under truck work great video thanks Sam

@Watchyn_Yarwood

Күн бұрын

He's a machinist that drives a truck on the side.

@dennisreed3382

7 сағат бұрын

I drove for 25 years. I can use a lathe, weld, and any other machine shop tools. Guess I'm the 1 percent, huh?

Yelling at Seri, I was die’n ova here.😂 Funny how she’s always listening when you don’t want her to then when you’re stuck under a truck she’s rock’n out not paying attention. 😂

@professorfalken4600

2 күн бұрын

Seri I a spy tool, shut it off

@gullreefclub

2 күн бұрын

I hate that spying bitch just like any other AI utility they all act like spyware to me

Firstly, happy Independence Day, to friends and family. Sam, my buddy, back in the 80's turned the cooler sideways, and made up a set of louvers, for one side. The fin side, was towards the transmission about 2 inches below, with the louver openings towards the rear. With a gear pump, run by a modified wiper motor, to circulate the gear oil. Air flow, due to the venturi effect, was all that was needed. This system worked wonderfully in the Canadian Rockies, fully loaded on the long 6 and 7% grades. The temps would stay roughly 10°F above normal.

Your Grandpa would be so PROUD!!!

Back in the 80’s and early 90’s I worked at a shop that specializes all things tow trucks and as a result I installed lots of PTO’s and Hydraulic pumps. One of the things we did was I make our own mounting bracket/tab instead of that two piece weld together setup was we would tack the two pieces together and then use that as a template to trace our our 1 piece bracket/tab. Additionally we fabbed up a cutout for the PTO that was based off rpm of the engine and a pump cutoff switch based on hydraulic pressure

Love to see a man actually finish a good job unlike some other sites .,Pride is alive in you and it wont die ever. Thank you for this work story

Got an 89 LTL in Australia. Still working. Great old trucks.

Good to watch someone who really knows what he's about.

I liked this video. Thanks for taking us along.🏁🏁🏁

Great job Sam keeping your equipment maintained and up to code takes a tremendous effort and you take it a step further by keeping it clean and looking good Shows you take pride in what you’ve done and own

It's always a pleasure to watch someone else doing the work! I learned that lesson the hard way too -- as soon as you're finished draining the oil, the drain pan gets removed and emptied. Most of our trailers work off the truck hydraulics. On the quad axle float the ramps and lift axles work off the truck hydraulics, but the massive winch (30T from memory) needs an auxiliary power pack. Originally it was all plumbed to work off the little onboard Honda power pack (now removed), but the winch barely moved and the truck hydraulics weren't much faster! The big trailer mounted unit powers it in/out at a decent rate, although we hardly ever use the winch. Better to have it and not need it, than vice versa!

One of my favorite channels.

Nice work. Really nice work. The truck looks spectacular. Happy hauling. 👍👍👍

Great job on the additions and the maintenance. The old Ford is looking all shiny again!

Scrappy Sam, it's good to see you have a video out today.

Damn i hate using dump pumps for wet kit application. I do agree on the hate for "scotch locks", those should be illegal. Ford is looking amazing, and your tank mount spacer idea is perfect! Old trucks always need work! Reminds me of the adage of how girlfriends and go-karts are alike. You ride them for a half hour on the weekend and work on them the whole next week.

Good morning Sam! Happy 4th of July to everybody. 🎉🎊🎇🎆

Happy Independence Day Sam. Thanks for the update 😊

I have used the field replaceable fittings on many hydraulic lines, and I have never had one fail. You are the first person I have heard with failures. I use a double wire hose, and the fittings that match. Thanks for sharing your experience.

Love these old Ford trucks. I remember when they were a real competitor in the market. We had an old 850 that was bulletproof! Thanks for the video! 👍

Thanks Sam, was really looking forward to this update. Really enjoy watching your videos. Can't wait to see the next Mini-Mack video!

Great job Sam keeping your equipment maintained 😀

My gf loves it when I watch your videos when we are getting busy. 🎉

The polish job looked fantastic 🦘

The only USA channel who I watch that uses a 5 inch grinder with the guard on. You only need 1 cut off disc to disintergrate and cut you up before thinking, YES a guard IS a good idea..

@ScrappyIndustries

2 күн бұрын

I agree 100%. Sometimes you have to take it off but I try to avoid it

Absolutely love the channel and the content two of my favorite trucks please don’t stop or change what yer doing especially when you and Matt are each others channels it’s great awsome videos thank you happy 4th

Awesome and outstanding as always.Thanks for sharing and taking us along

My favorite truck I ever owned or drove. Was totaled on job site by a 350 cat excavator. Was a great truck!

@ScrappyIndustries

Күн бұрын

Jeez poor girl!

Man , that’s what I want to do on my Mack! Thanks for showing me how to do it 👏🏽👏🏽👏🏽👏🏽👏🏽👏🏽👏🏽👏🏽

That is a really nice lathe, no bearing noise, and looks like the runout is good.

Great job the truck looks great, we had a 1986 9000 brings back memories. Have a happy 4th of July

Great job and best of all: you always finish the project - congratulations

One of the best that I have seen. Well done. Very entertaining first thing in the morning in NZ.

Excellent outcome!!!

Give Loctite 545 a try on your fluid fittings. I had a leaky 3000 lb hydraulic fitting on a John Deere tractor 6 years ago that I could not get to stop leaking. I tried Teflon no go. Someone told me about 545, used it and to this very day, it has not leaked one drop. I use it on every fluid fitting on the farm except residential plumbing. Not one single leak on anything ever.Try it you'll like it!

That is a great looking truck young man. Nice set up on the wet line kit, I like your attention to detail and your thinking on repairs and upgrades, thanks for the update, enjoyed watching, appreciate your time.

Well Sam you are getting an education on this install, and we just had to put our 7 year old Beagle down, she had a tumor on her spleen, if they took her spleen out, she'd only have about another 8-9 months of life, so we decided to put her out of pain and discomfort I'm still missing her. Dave D.

We can see better with new lights you put in..them small projects do add up...but we get some good to watch...with the inspector. 🐾🐕🐾

Great work this will be a dry work shop or ur planning to put some heat for the equipment u will be storage in . Thank you for all the hard work and blessings to u and senior plus fam 🙏

What a beautiful truck ❤

Good morning, Nice work. What a beautiful truck, bravo!

FORD (Found On Road Dead) you are keeping your Ford on the road for another day. Great job Sam!

Really like your giving that beast of a Ford the attention it deserves. Ford's best that body style in particular.

@ScrappyIndustries

Күн бұрын

Thanks!

Really enjoyed this one! 👍

Great job, well done.

Great video Sam!!!!

Great project

Great job Sam😊😊😊

Thanks Sam love the videos and Happy 4th of July and I Enjoy the video .

Great video Sam, thanks for sharing the process!!

@ScrappyIndustries

Күн бұрын

Any time!

looking good

The Big Louie is looking great there, Sam 🤟🏼 Kudos for the wet kit install too 🙂

We had reusable fittings at the shop I worked at loved em.

Sam, i really really love that ford. What a beauty.

Nice job!

Beautiful!!

As always bro it made for great viewing and the truck looks right purdy too. Safe travels. Ken.

Sammie, If it was easy, anyone could do it. You and ole Diesel Creek take on some real interesting projects, thanks for the details.

Brilliant video Sam watching from Edinburgh Scotland UK 🇬🇧 , happy independence day Sam

Geat video. thanks Sam.

Looks good from Michigan 🤠 Nice job Sam

I've made hydrolic hoses with those ends myself. Nice!

Wow is a beauty you did a great job Sam 👍 👍

You do great work! 100k very soon.

52:52 Love the reference!! Eric Idle is amazing.

@afberglund2764

18 сағат бұрын

Eric Idle is not dead

@arcanewyrm6295

17 сағат бұрын

@afberglund2764 I stand corrected. Could've sworn I saw an obit for him a couple years back. I was probably just wrong. 🤷‍♂️🤦‍♂️

Man thats a nice ole truck!

😂I just took a break from putting new straps on my fuel tank and found you doing all this😂 I know your pain Sam 😂😂 awesome videos

@scottmoodysr9449

2 күн бұрын

I drive through pa all the time and always look for you or Matt 😂 I'd love to meet you sometime.

Happy canada day and happy 4th dude thx for sharing. Keep up good work

well done

Love the old trucks, the new one's are nothing but Chineseum Krap

Good one Sam

I run an old truck as well. My low air buzzer doesn’t work either. Worried I’d get popped for it I did a little research and found that: as long as you have a pressure gauge and either a buzzer OR indicator lamp, mucho bueno! Good to go

@johnsweet8410

2 күн бұрын

Also, back up warning buzzer works as a stand-in for the light and (IMHO) better.

Sam you two beautiful trucks

Great video Happy 4th of July

Nice!

Well done 👏

Happy Independence Day Sam. Looks great !!

Loved the video! Would love for you to do a video on how the lowboy trailer works, is attached together.

WILL do

Sam, that was a fun watch. That Ford is almost too purtty to put it to work. Love how well adjusted to shop noises your dogs are, obviously you trained them well. Reminds me of when my Lab was a puppy, I would bring her into the garage and showed her the noisy equipment and while petting her I would place one of her paws on the running machine, she leaned and never was afraid. Thanks for sharing 👍 - HAPPY 4TH OF JULY TO ALL 🇺🇸

👌👌👍👍 Nice! Thanks for the video.

Old truck that is newer boy it sure looks and sounds awesome well done Sam now to see a big load on looking forward to that video you have a gem there enjoy 👍👋🇨🇦

That's a nice truck Sam! Greetings from the Netherlands

good job sam, that job is a bear

Happy 4th July everyone regards Andy from Australia

That was great! 🤣🤣 I was laughing out loud!! NO! NO!

@ScrappyIndustries

2 күн бұрын

😂😂

Happy 4th, Sam.

Happy Independence Day! Ten thousand thumbs up!!!!!

Love your vid. I came from letsdig,and Diesel Creek.

Funny that both you and Yogi are tappin you feet to the music @24:30 😆

Awesome Job Sam Happy 4th July

Now what you need to get is a high-idle for the ford

I have a PTO on my ten speed freightliner .Run a vacuum pump with right angle gear box and a Lovejoy coupling. When I engage my PTO. I put clutch down to engage the clutch brake.Also put transmission in gear while flipping the PTO switch put transmission in neutral while letting the clutch out. It seems to grind less that way

Happy 4th ofJuly . Greetings from Germany

Happy 4 th. Looks like your dripping liquid gold out of the 5-gal pump. HAVE A GREAT DAY!

Love The old Ford

Hi Sam & it's is Randy and i like yours video is Cool & Thanks Sam & Friends Randy

The looser side of the tolerance than the tighter side 😂 said no man ever! Lol 😆

"SEMIE" as well Sam. I watch Highway Through Hell & HR 401. Both are Canadian wreck/recovery shows done by Discovery.

Yogi approved❤