Ford Fusion Rear Bumper Cover And Taillight Removal (2013+ ) Second Gen
Guide to removing the rear bumper cover and taillights on the new 2013+ Ford Fusions.
Жүктеу.....
Пікірлер: 39
@rccola44944 жыл бұрын
It don't get much better than this. I needed to remove rear bumper on 2014 Fusion because someone backed into the wife's driver side rear quarter panel. The impact hit the wiring for the rear parking sensors up against the steel bumper perfectly to cut them clean off. Took about 2 hours of removing … adding wire and soldering to the 6 sensor signal wires. Hooked things up before assembling everything back together and it works. Not very much damage to the bumper … like a 2 inch slit … hard to see so not going to worry about that. Thanks for taking the time to make this very helpful video.
@velasco330 Жыл бұрын
Hi Dude, nice going. As you are performing that task, it seems so easy to do. It helped me a lot. Thanks for sharing in such easy way. Best regards from Brazil...
@happywrenching
Жыл бұрын
Greetings! Glad it helped!
@Rick_Schott3 жыл бұрын
Got hit in the back, no real damage but one of the backup sensors popped in. Only way to fix it was remove the bumper cover. Saved this guy a bill from the collision shop! Great video, easy sub.
@mondeq19 жыл бұрын
Sir, I found this video very useful when installing a towbar on a 2015 Ford Mondeo, (EU version of Fusion). I thank you for your time and also the very high quality. At 1.21 where you removed the rear light, I use a cable tie. I fed it up from the bottom of the light in a 2 o'clock direction and the joined it together. This left me with a loop to pull the unit straight off. I feared using a pry tool in case I scratched the paint as I would not be as experienced as you. Again thank you for a wonderful video.
@happywrenching
9 жыл бұрын
+mondeq1 Glad it worked out for you :)
@madmaxhornuberdriver78377 жыл бұрын
Well, this was exactly what I needed. And great camera work and lighting!
@andrewproctor87813 жыл бұрын
It’s not boring with the clips and nut and bolts, it helps us procrastinators that don’t remember lol
@ForceTranq7 жыл бұрын
Thanks, I was looking for this kind of video
@bodyshop80084 жыл бұрын
Great video! How does Mom like you always taking her car apart to make these videos? lol Very helpful info.
@DCIROCK238 жыл бұрын
I'm very interest want to know how 2014 titanium Fusion led tail work on SE Hybrid?
@crisgarces038 жыл бұрын
Hi, what if the plastic part of the bumper with the red "reflectors" needs to be replaced, is that possible?
@joseph_b3194 жыл бұрын
I wish the front light replacement was that easy.
@asiajxO28 күн бұрын
is there a link to this car part
@crisgarces038 жыл бұрын
I believe it's called the "rear bumper center insert" with reflectors.
@mikew96733 жыл бұрын
thank you very much for the detailed video!
@peterandreadis48644 жыл бұрын
This was terrific and super helpful Thank you!
@johnlkeck5 жыл бұрын
Does anyone have a good recommendation on where to buy a new bumper?
@jigarbavishi130210 жыл бұрын
when putting back the tail lights should u hear a click to make sure the unseen screw is fully installed ?
@zabilbakhshaliyev17832 жыл бұрын
Hello guys ! Could be Ford Fusion 2015 rear left fender replaced ? I have damaged my car . Anyone have any video or references? Thanks guys .
@Relski4153 жыл бұрын
Will this work on 2006 fusion
@terrywarnett32708 жыл бұрын
Hi, There. Nice Video and this should help me out. Someone scraped the side of my 2016 Fusion and the side has come out at the top where the clips are that you show in the video that just push in? I tried pushing it back in but it will not go. any ideas?
@tomilheirobarbalho61174 ай бұрын
Good job 👍 thanks you
@batsukamuro8 жыл бұрын
Thanks for this. Very well done.
@AdmirCustovic3 жыл бұрын
Great video. Thank you.
@jasminecrawford53004 жыл бұрын
Link to where you ordered the bumper?
@luisarmenta80349 жыл бұрын
This is very helpful thanks guys
@victoriagkl21733 жыл бұрын
Very helpful thank you!
@pcnetworx12 жыл бұрын
Fantastic!
@m2aroz9 жыл бұрын
Thanks very nicely done!
@question7774 жыл бұрын
Nice video. Thanks !
@umairmohammed57024 жыл бұрын
Top video !!
@daeahn41610 жыл бұрын
If your rear bumper has a sensor, do you have to remove any wires?
@happywrenching
10 жыл бұрын
If you do have the rear parking assist sensors then there should be a single connector on the driver's side of the rear bumper that you will need to unplug.
@daeahn416
10 жыл бұрын
Huh? Where is that?
@Twinjeremy7 жыл бұрын
those nuts are indeed 10mm not 12 like he said... at least on my 2013 fusion energi it was
@7ALABEB9 жыл бұрын
Please l want tetinum bamber for se (l want 2 exsust) like tetinum
Пікірлер: 39
It don't get much better than this. I needed to remove rear bumper on 2014 Fusion because someone backed into the wife's driver side rear quarter panel. The impact hit the wiring for the rear parking sensors up against the steel bumper perfectly to cut them clean off. Took about 2 hours of removing … adding wire and soldering to the 6 sensor signal wires. Hooked things up before assembling everything back together and it works. Not very much damage to the bumper … like a 2 inch slit … hard to see so not going to worry about that. Thanks for taking the time to make this very helpful video.
Hi Dude, nice going. As you are performing that task, it seems so easy to do. It helped me a lot. Thanks for sharing in such easy way. Best regards from Brazil...
@happywrenching
Жыл бұрын
Greetings! Glad it helped!
Got hit in the back, no real damage but one of the backup sensors popped in. Only way to fix it was remove the bumper cover. Saved this guy a bill from the collision shop! Great video, easy sub.
Sir, I found this video very useful when installing a towbar on a 2015 Ford Mondeo, (EU version of Fusion). I thank you for your time and also the very high quality. At 1.21 where you removed the rear light, I use a cable tie. I fed it up from the bottom of the light in a 2 o'clock direction and the joined it together. This left me with a loop to pull the unit straight off. I feared using a pry tool in case I scratched the paint as I would not be as experienced as you. Again thank you for a wonderful video.
@happywrenching
9 жыл бұрын
+mondeq1 Glad it worked out for you :)
Well, this was exactly what I needed. And great camera work and lighting!
It’s not boring with the clips and nut and bolts, it helps us procrastinators that don’t remember lol
Thanks, I was looking for this kind of video
Great video! How does Mom like you always taking her car apart to make these videos? lol Very helpful info.
I'm very interest want to know how 2014 titanium Fusion led tail work on SE Hybrid?
Hi, what if the plastic part of the bumper with the red "reflectors" needs to be replaced, is that possible?
I wish the front light replacement was that easy.
is there a link to this car part
I believe it's called the "rear bumper center insert" with reflectors.
thank you very much for the detailed video!
This was terrific and super helpful Thank you!
Does anyone have a good recommendation on where to buy a new bumper?
when putting back the tail lights should u hear a click to make sure the unseen screw is fully installed ?
Hello guys ! Could be Ford Fusion 2015 rear left fender replaced ? I have damaged my car . Anyone have any video or references? Thanks guys .
Will this work on 2006 fusion
Hi, There. Nice Video and this should help me out. Someone scraped the side of my 2016 Fusion and the side has come out at the top where the clips are that you show in the video that just push in? I tried pushing it back in but it will not go. any ideas?
Good job 👍 thanks you
Thanks for this. Very well done.
Great video. Thank you.
Link to where you ordered the bumper?
This is very helpful thanks guys
Very helpful thank you!
Fantastic!
Thanks very nicely done!
Nice video. Thanks !
Top video !!
If your rear bumper has a sensor, do you have to remove any wires?
@happywrenching
10 жыл бұрын
If you do have the rear parking assist sensors then there should be a single connector on the driver's side of the rear bumper that you will need to unplug.
@daeahn416
10 жыл бұрын
Huh? Where is that?
those nuts are indeed 10mm not 12 like he said... at least on my 2013 fusion energi it was
Please l want tetinum bamber for se (l want 2 exsust) like tetinum
excellent demo