Ford Fusion Front Bumper Cover Removal (2013+ ) Second Generation
Guide to removing the front bumper cover on the second generation Ford Fusions.
Жүктеу.....
Пікірлер: 283
@lwthowe2 жыл бұрын
Such a superior video. Most people do not show how they unscrew and unclip everything in detail, but you do. Very well done! One suggestion: Sometimes you start each segment with a closeup and it's so close it's hard to tell where on the car you're working on at that moment. You might start each segment explaining where on the car you're at and what you're going to do next, and then zoom in and show the close-ups as you've done. Other than that, this is so much better than anything else I've seen on how to do this. Thank you.
@kbaker20237 жыл бұрын
Jesus. No wonder whoever owed my car before me didn't fix the bumper clip under behind the wheel well/under the headlight. Great video sir. Thank you!
@MDiaz2
2 ай бұрын
Gs
@rellik187redrum8 жыл бұрын
future models will require engine removal for oil changes
@delorean117
8 жыл бұрын
This is when you ask Red Green to do it for you.
@raymondramirez9177
7 жыл бұрын
Buy an electric car. No more oil changes!
@jw9517
7 жыл бұрын
rellik187redrum hahah
@chauderskine9313
7 жыл бұрын
Lmao
@MarcosGarcia-xg1rf
3 жыл бұрын
Nah
@mintpatrol33195 жыл бұрын
Ford worker: you think that bumper is secure yet Ford engeneer: yea but let's add 20 more screws just in case
@squidproquo2241
4 жыл бұрын
@Reggie Got Projects _ And hide the head light access behind the bumper.
@rahhal83
4 жыл бұрын
😂😂😂
@bohemialite6371
4 жыл бұрын
That is so funny what you said but it is so true😆😆😆
@michaelmurray7199
3 жыл бұрын
If you think that’s bad, just wait til you have to remove the front fascia on a BMW, Mercedes-Benz or and Audi.
@gregorymaly1643
3 жыл бұрын
Let's bolt the headlights to the frame, that way the bulbs will be impossible to replace
@cruzruiz98676 жыл бұрын
god this is making me rethink about doing the front led upgrade by myself on my 16 fusion se.....
@Wechosworld
2 жыл бұрын
Try it it wont hurt as long as you give yourself a day to figure it out
@cameronj.8621
2 жыл бұрын
Dude I’m adding leds to my fusion now and it’s hell. By myself it’s already taken more than 4 hours.
@casheighty8
2 жыл бұрын
The high beams are impossible without pulling the headlight but I did my low beams with one hand.
@jackzhao6043 жыл бұрын
So many people complaining about how hard it is. I’m 20 a broke college student, can’t afford full insurance so hitting a deer ain’t covered. Damaged all the way back to the upper radiator support, I don’t have money to take it to the shop so I replaced everything myself off of diagrams cuz some of these don’t have KZread videos. I replaced from bumper side fender shutter fog light head light radiator support header mounted and everything that’s on it
@Xratos19917 ай бұрын
Using a 10 inch quick adjusting groove joint pliers with curved jaw from Home Depot I was able to twist and pull the light bulb without removing the bumper. This was on a 2016 fusion. I know have a 2018 Fusion hybrid and thankfully on these year models you don’t have to do any of this its right there in the open ez change.
@wantsanewvehicle9 жыл бұрын
I just bought a 2013 se on Friday. I wanted to my put hid lights into it, but first I wanted to see how the halogens looked. However, I was anxious..lol. So, Friday night I put my leds into the fogs. Saturday evening I decided it was time to put the hids into highs and lows. I already had the bottom piece and the thumb screws out of the wheel wells from what I put the fogs in (it got dark and I didn't have time to reinstall). After reading your comment that says you should be able to pull the bumper far enough away to get the headlight assembly out (impossible to change light bulb without doing so), it worked fine on one side. I went to do it on the otherside and the bumper..fell off. I did not touch the screws in the wheel well, or the bumper bracket (5:30-6:30). The whole bumper did come off though. I don't believe I broke anything and it fits back perfectly o.O..
@TomCook1993
6 жыл бұрын
wantsanewvehicle should’ve bought the titanium. SE sucks
@gjash4935 жыл бұрын
2019 September Bro you really know how to make good videos. I have Ford fusion and I need more videos like this...
@batsukamuro8 жыл бұрын
Dude! You're a freaking life saver. Thanks for this! Really.
@lawrencepunsalang86302 жыл бұрын
Thank you for creating this video on the removal and installation of the front bumper. It is very helpful.
@standlegweak9854 Жыл бұрын
Best video there is on this process. Excellent work!
@neilreid22982 жыл бұрын
Really, really good vid and explanation. Not that hard of a job but super to see this vid first. I tried replacing my low beam bulbs without removing the bumper- no can do. Many thanks for this vid!
@SkaffOKP5 жыл бұрын
Great tutorial. very helpful ! Thanks! but ;) you dont need unscrew (left and right ) whole slide. example on 6:00 min. video. only unscrew main screw. ofcourse you must pull plastic pin ( 3 per side) example 1:50 on this video. wireds are long :-) you can unpluged it on top side
@kevinpohl2800 Жыл бұрын
Changing windshield for new wipers would be another good idea 👍🏻
@velvetpaws999 Жыл бұрын
Wow, Man! You are brave! Bravo! I lost all hope as you progressed taking off screw after screw after screw after.... help! another six! Oh no, more screws.... honestly, I gave up... plus all the connectors to unplug... I am sure I would never remember what screw goes where and in what order, lol. It would be painful to think I was finished when I have still 20 screws that I couldn't remember I took out, ha ha ha.... Yeah, this would raise my motivation to go the the Ford Dealership and let them deal with it. You did really excellent! Are you a pro car mechanic? Can I hire on as an apprentice with you? I'm sure I'd learn a lot! Thanks again for the great clip!
@omahasho46584 жыл бұрын
Dude I was installing a larger intercooler and nobody at all that did them for the 1.6 did a video about it so tanks so much for making this video showing how to take the bumper one
@bababoy117 жыл бұрын
Ford made this nearly impossible...
@69Pigman11 ай бұрын
Absolutely spectacular. You have given me a wealth of information with this video, that I have been searching for. 🍺🍺
@TheHopster64 жыл бұрын
Thank you for the video!! Had to do some bumper cover work and this was excellent!!
@ceem16853 жыл бұрын
Bumper pops off the mounting brackets so you don't have to take them off on the corners. One less thing to mess around with
@meg.k.jensen9 жыл бұрын
Thank you for making this video. I was able to remove the bumper and replace the grills!
@m2dc13
9 жыл бұрын
How did you take odd the slats?
@m2dc13
9 жыл бұрын
The grill how did you get it off?
@hermangavin2064
3 жыл бұрын
Insanity
@gameshot9115 жыл бұрын
Thanks for the video, helped me replace the grill on my car! All those push pins and screws, though.... will have nightmares for a while.
@mirandacollins393
4 жыл бұрын
Mike Goldberg about how long does it take to replace the grill ??
@nickrobin52352 жыл бұрын
On the driver side, to change the light bulb just remove the air intake box and your finger can fit to change the bulbs
@ppal19812
Жыл бұрын
And the passenger?
@chadkochmann79583 жыл бұрын
Very nice job with taking this apart and shooting the video. Thank you.
@asaelestrada3804 жыл бұрын
Bruhhh I don’t want to change my bumper no more 😭 just gonna live with the rip in between 😪
@SteveD3003 жыл бұрын
I'd rather just pay the ticket(s) for my headlight being out. Smh
@cindyjordan6734
13 күн бұрын
Waste of money it's not that hard, and you don't actually have to remove the entire bumper. Just the top half loosen it up enough to get head lamp out.
@ryanneidinger74575 жыл бұрын
Just finished up putting in my new grill. What a pain in the ass but totally worth it
@kevinyung17437 жыл бұрын
Great video man, i have a question though, im currently rebuilding my 2016 ford fusion and there is a cable that im confused on where it goes, its the one by the hood tab that you press to open it, its the only one by itself up there and it runs along the left headlight. -Thanks
@RandySForbes7 жыл бұрын
I saw a few comments about replacing the upper grill. One said they did have to take off the bumper, the others did not further comment. Do you have to take off the bumper to replace the upper grill?
@ryan_duffy8 жыл бұрын
Thanks for the help. I just took mine off and fixed a dent 👍
@khamis85310 жыл бұрын
Can you do a video on how to remove the headlights?
@happywrenching
10 жыл бұрын
I've been wanting to but unfortunately I don't know when I'm going to get my hands on the Fusion again.
@khamis853
10 жыл бұрын
Do you have to remove the bumper to get a new set of headlight assemblies installed? Thanks
@happywrenching
10 жыл бұрын
alex khamis Technically, no. You have to remove the 5 thumb screws - 3 inside the wheel well and two on the bottom of the bumper. You then have to remove all the screws and clips at the top of the bumper. This should allow you to swing out the side of the bumper far enough to remove the headlight.
@thebigdog11424 жыл бұрын
This video is helpful but something are a little different on the 19 like the thumb screws in the wheel wells are now 1 pull tab and 2 screws also the wiring harness goes from the right side of the car across the bumper to the other side so you can't fully take the bumper off because of it
@stanleyhenry37002 ай бұрын
I was looking at my granddaughter's 2017 fusion,where she had a collision that damages her driverside bumper and fender. I noticed that they are torn-out holes holes under the bottom that the bumper is secured. What is the name of that part, I would like to replace it. Is that you called the underbody cover?
@edgarn57397 жыл бұрын
What are those two electrical connectors on the drivers side? I can't find front side marker lights on these fusions.
@AsheGyurik2 жыл бұрын
Is there a way to bend it open just enough to get a hand in there? I have a dead bird stuck in there and I really don’t wanna take 50 screws and clips out 🤦🏻♀️
@michaelwoods7458 Жыл бұрын
I going to install fog lights on a 2020 ford fusion, that never had them before. This will get me started. Do a video on that please
@ariass9345
Жыл бұрын
I wanna but led light bulbs in my 15 fusion and I’m to lazy to do all this stuff 😂. Why do car nowadays make it so difficult to work on
@NikolaGluvakov9 жыл бұрын
I wish we have channel like this for the European version - Mondeo.
@detailingdiaries6562
6 жыл бұрын
Nikola Gluvakov check out a channel by Alan Howatt 👍
@wiskipete9 жыл бұрын
Dam all this for just two lights!!
@PisaniProductions3 жыл бұрын
you think it's possible to do without wheel replacement or jack? Maybe turning the wheel would give enough clearance?
@TheCpot232 жыл бұрын
hello, I hope you read this. do you know where the horn is located at. in my car it is damge and i need to replace it. but i have no idea where it is.
@yemariamkebede1131 Жыл бұрын
May I please get information on where I can get the complete front bumper for a 2017 Ford Fusion?
@badplayer18454 жыл бұрын
The thumb screws on my car look different
@jmiles9836
4 жыл бұрын
Same here mine are different too. And no need to drop the cover on the bottom ( remove the 5 screws at the front attached to the bumper) or remove the bumper brackets.
@eb_reviews5 жыл бұрын
This is a nightmare!
@alanjm12346 ай бұрын
Crazy that you have to do this to replace a bulb! But at least it's easy enough.
@slavkocorluka48354 жыл бұрын
I have a 2016 Ford Mondeo Mk5 and I plan to put a front grill, so I wonder if it is the same in the last generation from 2013 to 2020? Tnx..
@caleb8864 Жыл бұрын
I cat ate my wires last night 🤦🏾♂️like it’s split so I need help plz
@braedonmetz97037 жыл бұрын
Thank you so much for this video great in depth and it helped me so much with replacing my grill ,good work
@robertsotela
6 жыл бұрын
Did you have to remove the whole bumper just to swap out the grille?
@Python1084
2 жыл бұрын
Yes
@shotakajaia30435 жыл бұрын
What is difference between Ford fusion's 2014 front bumper and Ford Mondeo MK5 2015 front bumper? Or both are same?
@ryankejr4315 жыл бұрын
Great video. Made the changing the bumper cover easy!
@187deserteagle2 жыл бұрын
Great video how do you change the light bulbs
@LPKizzle9 жыл бұрын
okay so you say you can remove the headlights without pulling the bumper? how would you go about doing this? do you have a video? im not talking about the bulbs i mean the whole housing
@leahsparks84366 жыл бұрын
The vent thing that’s on the front of the car that’s connected to the bumper
@kckrol855 жыл бұрын
If I need to get access to remove the fender. Do I need to remove that bumper bracket as you did. Or just the three clips in the liner and pull out the cover to get access to the fender bolt where it meets the front bumper cover?
@leahsparks84366 жыл бұрын
So I knocked the front air vent or whatever it’s called out of place,’. How do I pop it back in?
@kgore260111 ай бұрын
to change a light bulb tho?
@djlienhard382811 ай бұрын
Where could I buy a new one of these ?
@dennisschneider96707 жыл бұрын
how do you change the headlights without removing the bumper cover. everywhere I see says you do.
@ramivalencia
7 жыл бұрын
dennis schneider You may be able to change the high beam and side marker bulbs without removing the bumper, but you will need small hands. To remove the entire headlight assembly, you have no other choice but to remove the screws and clips holding the bumper and then pull it out just enough so that the bottom of the assembly can clear the bumper. Just FYI, the bottom of the headlight has a piece of plastic that is about 1.5 inches that you can't see. That's why you have to move the bumper.
@Matrixito2 жыл бұрын
Does anyone know if the Ford Fusion front bumper from a 2017 will fit on the 2015/16 Fusion? I'm thinkin on buying the 17 bumper so I can upgrade my 2015 front bumper (just for the look of the square fog lights)
@umaid1878 жыл бұрын
im trying to install opt7 6000k hids but when i poppedy bumper off a little i couldnt manage to take my lights or anuthing out
@j.omarjackso47186 жыл бұрын
What i have to do for change the front lights, i mean, to remove the faros
@MrG_Landscaping4 жыл бұрын
Been trying to locate the horn on my 2015 fusion energi. Seems like I have to take off font bumper. You know better,,, is that the case? If so thanks for the great video.
@Sean21795 жыл бұрын
I took the bumper off my 2013 Ford Fusion se 1.6l and there’s a plug for the active grill shutter but no unit to plug it into. Why?
@agustingonzalez4766
4 жыл бұрын
Same. I've been looking thinking something fell out something
@brochurst8318
4 жыл бұрын
Did you guys ever figure this out? Having the same problem right now myself
@cliffrhodenizerjr.13338 ай бұрын
This is the main reason why I sold mine and will never buy another Ford.
@mohammedhilabi4864
4 ай бұрын
Not easy 😢
@MrCaddillacMan3 жыл бұрын
Hey do u have a video changing the headlight bulb on a 2013 Ford Fusion
@jayramirez68129 жыл бұрын
Do you need to remove the bumper cover to just replace a grille ? I bought a new one to replace the boring factory grill
@mistadontplay277
8 жыл бұрын
+Jay Ra,irez were you able to put the grille on without removing the bumper?
@robertsotela
6 жыл бұрын
How was the install?
@patricksmith13619 жыл бұрын
I just want to replace my damn headlamp bulbs! Is there an "easy" way? All I've ever read is that I have to remove the bumper, which is downright depressing considering I had my old car's headlamp change time down to under 30 seconds...
@jchaney123 Жыл бұрын
What does that last electrical connection do? Is that for the "hood latch" dash warning light? I removed my bumper to add a tow bar base. Put the bumper back on and now my "Hood Latch Light" stay on all the time. Trying to figure out what went wrong. Hood latch works fine, just the warning light stays on.
@happywrenching
Жыл бұрын
Look at 7:08 - to the left of the driver headlight there is a gray connector (below the yellow lever). Thats the hood latch connection.
@dannyfernandez8700
Жыл бұрын
if the latch does not completely latch the light stays on. when you close hood make sure the latch clicks @@happywrenching
@flyboy83644 жыл бұрын
I had to remove my bumper to remove headlights there was no way around it especially when unhooking/ hooking in the light harness
@frankbonwith7945
4 жыл бұрын
It can be done with out removing bumper but, trying to line the lights up is another issue.
@SteelRhinoXpress7 жыл бұрын
i'm convinced they designed it this way so that you would have to take it to a ford dealership and pay a ford mechanic take it off. there is no need to have to do all this just to take off the bumper cover other than what i just mentioned. it's all a marketing ploy between the car companies and the dealerships.
@Elyeyi05
5 жыл бұрын
My 09 Honda accord is the same way
@billylaswisse13885 жыл бұрын
Can anyone tell me where the block heater cord for this exact model is can not seem to find it or do i have to have 1 installed
@neonbongo55823 жыл бұрын
You know what I think I’ll stick with oem headlights
@corybarth5 жыл бұрын
I could not load the video for some reason but does anyone know the name of or part number for the black plastic clips that hold the bottom most accent trim pieces to the bumper? There are 8mm hex screws but then there are black clips (look like a pin that pushes into and locks in the trim pieces). I tore part of the right side trim away but as I looked underneath it seems if I could get my hands on these clips I could re-attach it myself. Thanks!
@ScanMan19673 жыл бұрын
You say you don't need to do this to change the bulbs,.....can you elaborate on this, please? The Ford engineers that designed this should be publically shot in front of all Fusion owners.
@majas73 жыл бұрын
is the mondeo in Europe engineered the same way?
@rinogeorge45135 жыл бұрын
Hey are you sure they were T25 Torx screws? can't find them online anywhere.
@KillaCowboy10 жыл бұрын
Hey do you have any pictures of the clips up front and where they go to? Both left and right side
@abbasfadhil4877 жыл бұрын
HOW TO MAKE SERVICE TO THE DRIVER DOOR ON THE FORD FUSHEN 2014
@cesarrivera17794 жыл бұрын
How do you remove the radiator? Do you have a video for it ?
@Vlad7sokruta6 жыл бұрын
How to take put on active grille shutters??
@josephjimenez65926 жыл бұрын
What do you have the car on? 4 jack stands?
@joecandor61453 жыл бұрын
Good video. How did you get Robin William's hairy arms to appear in your video?
@larrywalden6264 жыл бұрын
And? You did this for what reason?
@mattlogan10096 жыл бұрын
did you come across the engine block heater cord?
@fusionsportdaily16503 жыл бұрын
2013 and up are the third generation Fusions.
@happywrenching
3 жыл бұрын
There is no third generation. 2006 to 2012 and 2013 to present. That's it
@Chris-go9ti4 жыл бұрын
Remove the 17 and newer. Mine is not in that spot. It's worse. Also none of the screws are the same and the things on the side are no longer there. You also had some spacer in front. All different.
@macster14577 жыл бұрын
great video.. .can you do a dashboard removal on a 2016 ford fusion?
@ARM_19866 жыл бұрын
i just want know that Ford fiesta 2009 till 2015 model same way remove and install.
@leandrosena48256 жыл бұрын
Hi, where the external temperature sensor is located?
@jacobmoreno63394 жыл бұрын
Very helpful. Thanks!
@clutch28277 жыл бұрын
What does removing the two brackets on either side buy you? Seems unnecessary unless I'm missing something.
@happywrenching
7 жыл бұрын
Valid question - you are right, technically the brackets should not have to be removed. Notice that those brackets have plastic hooks that clip into the end of the bumper cover. I removed the brackets as a precaution. Those plastic hooks become brittle as the car ages and you run the chance of breaking them as you remove the bumper cover. Removing the bracket first ensures that nothing breaks.
@SilentPaul5 ай бұрын
Just a heads up for 2017+ sport owners extra bolts and clips and remove driver wheel. And good luck lol.
@enigmarocker7 жыл бұрын
Thank you SO MUCH for making this video! :)
@smurf13w175 жыл бұрын
can you send a pic of the hood latch sensor. i replaced my bulbs and im getting that warning on my dash that its open when its completely closed
@smurf13w17
5 жыл бұрын
my email is marcus.wilson413@gmail.com
@xanderdashredder10 жыл бұрын
Is there any chance you could make a video demonstrating how to remove the seats and rear deck?
@happywrenching
10 жыл бұрын
Wish I could but unfortunately it looks like I won't be making any Fusion videos for a while.
@jakewinburn30443 жыл бұрын
Do you have a video for how to change the headlights without removing the bumper cover?
@only1pedro
3 жыл бұрын
Impossible
@delorean1178 жыл бұрын
Nice clear concise video, thanks.
@MotopediaAe9 жыл бұрын
I really loved your video.
@davidprice6462 Жыл бұрын
You forgot to mention the wiring harness attached to the bumper that will snap and break if you don't know it's there and one side of the bumper comes off when you take the 37th bolt out. I learned this the hard way and now my outside air temp reading defaults to 50 degrees at all times when driving my 2014 Fusion. I hate this car with a passion. Plastic bumpers should never require 16 bolts, screws, and clips/brackets.
Пікірлер: 283
Such a superior video. Most people do not show how they unscrew and unclip everything in detail, but you do. Very well done! One suggestion: Sometimes you start each segment with a closeup and it's so close it's hard to tell where on the car you're working on at that moment. You might start each segment explaining where on the car you're at and what you're going to do next, and then zoom in and show the close-ups as you've done. Other than that, this is so much better than anything else I've seen on how to do this. Thank you.
Jesus. No wonder whoever owed my car before me didn't fix the bumper clip under behind the wheel well/under the headlight. Great video sir. Thank you!
@MDiaz2
2 ай бұрын
Gs
future models will require engine removal for oil changes
@delorean117
8 жыл бұрын
This is when you ask Red Green to do it for you.
@raymondramirez9177
7 жыл бұрын
Buy an electric car. No more oil changes!
@jw9517
7 жыл бұрын
rellik187redrum hahah
@chauderskine9313
7 жыл бұрын
Lmao
@MarcosGarcia-xg1rf
3 жыл бұрын
Nah
Ford worker: you think that bumper is secure yet Ford engeneer: yea but let's add 20 more screws just in case
@squidproquo2241
4 жыл бұрын
@Reggie Got Projects _ And hide the head light access behind the bumper.
@rahhal83
4 жыл бұрын
😂😂😂
@bohemialite6371
4 жыл бұрын
That is so funny what you said but it is so true😆😆😆
@michaelmurray7199
3 жыл бұрын
If you think that’s bad, just wait til you have to remove the front fascia on a BMW, Mercedes-Benz or and Audi.
@gregorymaly1643
3 жыл бұрын
Let's bolt the headlights to the frame, that way the bulbs will be impossible to replace
god this is making me rethink about doing the front led upgrade by myself on my 16 fusion se.....
@Wechosworld
2 жыл бұрын
Try it it wont hurt as long as you give yourself a day to figure it out
@cameronj.8621
2 жыл бұрын
Dude I’m adding leds to my fusion now and it’s hell. By myself it’s already taken more than 4 hours.
@casheighty8
2 жыл бұрын
The high beams are impossible without pulling the headlight but I did my low beams with one hand.
So many people complaining about how hard it is. I’m 20 a broke college student, can’t afford full insurance so hitting a deer ain’t covered. Damaged all the way back to the upper radiator support, I don’t have money to take it to the shop so I replaced everything myself off of diagrams cuz some of these don’t have KZread videos. I replaced from bumper side fender shutter fog light head light radiator support header mounted and everything that’s on it
Using a 10 inch quick adjusting groove joint pliers with curved jaw from Home Depot I was able to twist and pull the light bulb without removing the bumper. This was on a 2016 fusion. I know have a 2018 Fusion hybrid and thankfully on these year models you don’t have to do any of this its right there in the open ez change.
I just bought a 2013 se on Friday. I wanted to my put hid lights into it, but first I wanted to see how the halogens looked. However, I was anxious..lol. So, Friday night I put my leds into the fogs. Saturday evening I decided it was time to put the hids into highs and lows. I already had the bottom piece and the thumb screws out of the wheel wells from what I put the fogs in (it got dark and I didn't have time to reinstall). After reading your comment that says you should be able to pull the bumper far enough away to get the headlight assembly out (impossible to change light bulb without doing so), it worked fine on one side. I went to do it on the otherside and the bumper..fell off. I did not touch the screws in the wheel well, or the bumper bracket (5:30-6:30). The whole bumper did come off though. I don't believe I broke anything and it fits back perfectly o.O..
@TomCook1993
6 жыл бұрын
wantsanewvehicle should’ve bought the titanium. SE sucks
2019 September Bro you really know how to make good videos. I have Ford fusion and I need more videos like this...
Dude! You're a freaking life saver. Thanks for this! Really.
Thank you for creating this video on the removal and installation of the front bumper. It is very helpful.
Best video there is on this process. Excellent work!
Really, really good vid and explanation. Not that hard of a job but super to see this vid first. I tried replacing my low beam bulbs without removing the bumper- no can do. Many thanks for this vid!
Great tutorial. very helpful ! Thanks! but ;) you dont need unscrew (left and right ) whole slide. example on 6:00 min. video. only unscrew main screw. ofcourse you must pull plastic pin ( 3 per side) example 1:50 on this video. wireds are long :-) you can unpluged it on top side
Changing windshield for new wipers would be another good idea 👍🏻
Wow, Man! You are brave! Bravo! I lost all hope as you progressed taking off screw after screw after screw after.... help! another six! Oh no, more screws.... honestly, I gave up... plus all the connectors to unplug... I am sure I would never remember what screw goes where and in what order, lol. It would be painful to think I was finished when I have still 20 screws that I couldn't remember I took out, ha ha ha.... Yeah, this would raise my motivation to go the the Ford Dealership and let them deal with it. You did really excellent! Are you a pro car mechanic? Can I hire on as an apprentice with you? I'm sure I'd learn a lot! Thanks again for the great clip!
Dude I was installing a larger intercooler and nobody at all that did them for the 1.6 did a video about it so tanks so much for making this video showing how to take the bumper one
Ford made this nearly impossible...
Absolutely spectacular. You have given me a wealth of information with this video, that I have been searching for. 🍺🍺
Thank you for the video!! Had to do some bumper cover work and this was excellent!!
Bumper pops off the mounting brackets so you don't have to take them off on the corners. One less thing to mess around with
Thank you for making this video. I was able to remove the bumper and replace the grills!
@m2dc13
9 жыл бұрын
How did you take odd the slats?
@m2dc13
9 жыл бұрын
The grill how did you get it off?
@hermangavin2064
3 жыл бұрын
Insanity
Thanks for the video, helped me replace the grill on my car! All those push pins and screws, though.... will have nightmares for a while.
@mirandacollins393
4 жыл бұрын
Mike Goldberg about how long does it take to replace the grill ??
On the driver side, to change the light bulb just remove the air intake box and your finger can fit to change the bulbs
@ppal19812
Жыл бұрын
And the passenger?
Very nice job with taking this apart and shooting the video. Thank you.
Bruhhh I don’t want to change my bumper no more 😭 just gonna live with the rip in between 😪
I'd rather just pay the ticket(s) for my headlight being out. Smh
@cindyjordan6734
13 күн бұрын
Waste of money it's not that hard, and you don't actually have to remove the entire bumper. Just the top half loosen it up enough to get head lamp out.
Just finished up putting in my new grill. What a pain in the ass but totally worth it
Great video man, i have a question though, im currently rebuilding my 2016 ford fusion and there is a cable that im confused on where it goes, its the one by the hood tab that you press to open it, its the only one by itself up there and it runs along the left headlight. -Thanks
I saw a few comments about replacing the upper grill. One said they did have to take off the bumper, the others did not further comment. Do you have to take off the bumper to replace the upper grill?
Thanks for the help. I just took mine off and fixed a dent 👍
Can you do a video on how to remove the headlights?
@happywrenching
10 жыл бұрын
I've been wanting to but unfortunately I don't know when I'm going to get my hands on the Fusion again.
@khamis853
10 жыл бұрын
Do you have to remove the bumper to get a new set of headlight assemblies installed? Thanks
@happywrenching
10 жыл бұрын
alex khamis Technically, no. You have to remove the 5 thumb screws - 3 inside the wheel well and two on the bottom of the bumper. You then have to remove all the screws and clips at the top of the bumper. This should allow you to swing out the side of the bumper far enough to remove the headlight.
This video is helpful but something are a little different on the 19 like the thumb screws in the wheel wells are now 1 pull tab and 2 screws also the wiring harness goes from the right side of the car across the bumper to the other side so you can't fully take the bumper off because of it
I was looking at my granddaughter's 2017 fusion,where she had a collision that damages her driverside bumper and fender. I noticed that they are torn-out holes holes under the bottom that the bumper is secured. What is the name of that part, I would like to replace it. Is that you called the underbody cover?
What are those two electrical connectors on the drivers side? I can't find front side marker lights on these fusions.
Is there a way to bend it open just enough to get a hand in there? I have a dead bird stuck in there and I really don’t wanna take 50 screws and clips out 🤦🏻♀️
I going to install fog lights on a 2020 ford fusion, that never had them before. This will get me started. Do a video on that please
@ariass9345
Жыл бұрын
I wanna but led light bulbs in my 15 fusion and I’m to lazy to do all this stuff 😂. Why do car nowadays make it so difficult to work on
I wish we have channel like this for the European version - Mondeo.
@detailingdiaries6562
6 жыл бұрын
Nikola Gluvakov check out a channel by Alan Howatt 👍
Dam all this for just two lights!!
you think it's possible to do without wheel replacement or jack? Maybe turning the wheel would give enough clearance?
hello, I hope you read this. do you know where the horn is located at. in my car it is damge and i need to replace it. but i have no idea where it is.
May I please get information on where I can get the complete front bumper for a 2017 Ford Fusion?
The thumb screws on my car look different
@jmiles9836
4 жыл бұрын
Same here mine are different too. And no need to drop the cover on the bottom ( remove the 5 screws at the front attached to the bumper) or remove the bumper brackets.
This is a nightmare!
Crazy that you have to do this to replace a bulb! But at least it's easy enough.
I have a 2016 Ford Mondeo Mk5 and I plan to put a front grill, so I wonder if it is the same in the last generation from 2013 to 2020? Tnx..
I cat ate my wires last night 🤦🏾♂️like it’s split so I need help plz
Thank you so much for this video great in depth and it helped me so much with replacing my grill ,good work
@robertsotela
6 жыл бұрын
Did you have to remove the whole bumper just to swap out the grille?
@Python1084
2 жыл бұрын
Yes
What is difference between Ford fusion's 2014 front bumper and Ford Mondeo MK5 2015 front bumper? Or both are same?
Great video. Made the changing the bumper cover easy!
Great video how do you change the light bulbs
okay so you say you can remove the headlights without pulling the bumper? how would you go about doing this? do you have a video? im not talking about the bulbs i mean the whole housing
The vent thing that’s on the front of the car that’s connected to the bumper
If I need to get access to remove the fender. Do I need to remove that bumper bracket as you did. Or just the three clips in the liner and pull out the cover to get access to the fender bolt where it meets the front bumper cover?
So I knocked the front air vent or whatever it’s called out of place,’. How do I pop it back in?
to change a light bulb tho?
Where could I buy a new one of these ?
how do you change the headlights without removing the bumper cover. everywhere I see says you do.
@ramivalencia
7 жыл бұрын
dennis schneider You may be able to change the high beam and side marker bulbs without removing the bumper, but you will need small hands. To remove the entire headlight assembly, you have no other choice but to remove the screws and clips holding the bumper and then pull it out just enough so that the bottom of the assembly can clear the bumper. Just FYI, the bottom of the headlight has a piece of plastic that is about 1.5 inches that you can't see. That's why you have to move the bumper.
Does anyone know if the Ford Fusion front bumper from a 2017 will fit on the 2015/16 Fusion? I'm thinkin on buying the 17 bumper so I can upgrade my 2015 front bumper (just for the look of the square fog lights)
im trying to install opt7 6000k hids but when i poppedy bumper off a little i couldnt manage to take my lights or anuthing out
What i have to do for change the front lights, i mean, to remove the faros
Been trying to locate the horn on my 2015 fusion energi. Seems like I have to take off font bumper. You know better,,, is that the case? If so thanks for the great video.
I took the bumper off my 2013 Ford Fusion se 1.6l and there’s a plug for the active grill shutter but no unit to plug it into. Why?
@agustingonzalez4766
4 жыл бұрын
Same. I've been looking thinking something fell out something
@brochurst8318
4 жыл бұрын
Did you guys ever figure this out? Having the same problem right now myself
This is the main reason why I sold mine and will never buy another Ford.
@mohammedhilabi4864
4 ай бұрын
Not easy 😢
Hey do u have a video changing the headlight bulb on a 2013 Ford Fusion
Do you need to remove the bumper cover to just replace a grille ? I bought a new one to replace the boring factory grill
@mistadontplay277
8 жыл бұрын
+Jay Ra,irez were you able to put the grille on without removing the bumper?
@robertsotela
6 жыл бұрын
How was the install?
I just want to replace my damn headlamp bulbs! Is there an "easy" way? All I've ever read is that I have to remove the bumper, which is downright depressing considering I had my old car's headlamp change time down to under 30 seconds...
What does that last electrical connection do? Is that for the "hood latch" dash warning light? I removed my bumper to add a tow bar base. Put the bumper back on and now my "Hood Latch Light" stay on all the time. Trying to figure out what went wrong. Hood latch works fine, just the warning light stays on.
@happywrenching
Жыл бұрын
Look at 7:08 - to the left of the driver headlight there is a gray connector (below the yellow lever). Thats the hood latch connection.
@dannyfernandez8700
Жыл бұрын
if the latch does not completely latch the light stays on. when you close hood make sure the latch clicks @@happywrenching
I had to remove my bumper to remove headlights there was no way around it especially when unhooking/ hooking in the light harness
@frankbonwith7945
4 жыл бұрын
It can be done with out removing bumper but, trying to line the lights up is another issue.
i'm convinced they designed it this way so that you would have to take it to a ford dealership and pay a ford mechanic take it off. there is no need to have to do all this just to take off the bumper cover other than what i just mentioned. it's all a marketing ploy between the car companies and the dealerships.
@Elyeyi05
5 жыл бұрын
My 09 Honda accord is the same way
Can anyone tell me where the block heater cord for this exact model is can not seem to find it or do i have to have 1 installed
You know what I think I’ll stick with oem headlights
I could not load the video for some reason but does anyone know the name of or part number for the black plastic clips that hold the bottom most accent trim pieces to the bumper? There are 8mm hex screws but then there are black clips (look like a pin that pushes into and locks in the trim pieces). I tore part of the right side trim away but as I looked underneath it seems if I could get my hands on these clips I could re-attach it myself. Thanks!
You say you don't need to do this to change the bulbs,.....can you elaborate on this, please? The Ford engineers that designed this should be publically shot in front of all Fusion owners.
is the mondeo in Europe engineered the same way?
Hey are you sure they were T25 Torx screws? can't find them online anywhere.
Hey do you have any pictures of the clips up front and where they go to? Both left and right side
HOW TO MAKE SERVICE TO THE DRIVER DOOR ON THE FORD FUSHEN 2014
How do you remove the radiator? Do you have a video for it ?
How to take put on active grille shutters??
What do you have the car on? 4 jack stands?
Good video. How did you get Robin William's hairy arms to appear in your video?
And? You did this for what reason?
did you come across the engine block heater cord?
2013 and up are the third generation Fusions.
@happywrenching
3 жыл бұрын
There is no third generation. 2006 to 2012 and 2013 to present. That's it
Remove the 17 and newer. Mine is not in that spot. It's worse. Also none of the screws are the same and the things on the side are no longer there. You also had some spacer in front. All different.
great video.. .can you do a dashboard removal on a 2016 ford fusion?
i just want know that Ford fiesta 2009 till 2015 model same way remove and install.
Hi, where the external temperature sensor is located?
Very helpful. Thanks!
What does removing the two brackets on either side buy you? Seems unnecessary unless I'm missing something.
@happywrenching
7 жыл бұрын
Valid question - you are right, technically the brackets should not have to be removed. Notice that those brackets have plastic hooks that clip into the end of the bumper cover. I removed the brackets as a precaution. Those plastic hooks become brittle as the car ages and you run the chance of breaking them as you remove the bumper cover. Removing the bracket first ensures that nothing breaks.
Just a heads up for 2017+ sport owners extra bolts and clips and remove driver wheel. And good luck lol.
Thank you SO MUCH for making this video! :)
can you send a pic of the hood latch sensor. i replaced my bulbs and im getting that warning on my dash that its open when its completely closed
@smurf13w17
5 жыл бұрын
my email is marcus.wilson413@gmail.com
Is there any chance you could make a video demonstrating how to remove the seats and rear deck?
@happywrenching
10 жыл бұрын
Wish I could but unfortunately it looks like I won't be making any Fusion videos for a while.
Do you have a video for how to change the headlights without removing the bumper cover?
@only1pedro
3 жыл бұрын
Impossible
Nice clear concise video, thanks.
I really loved your video.
You forgot to mention the wiring harness attached to the bumper that will snap and break if you don't know it's there and one side of the bumper comes off when you take the 37th bolt out. I learned this the hard way and now my outside air temp reading defaults to 50 degrees at all times when driving my 2014 Fusion. I hate this car with a passion. Plastic bumpers should never require 16 bolts, screws, and clips/brackets.
OMG !!! Nice job (from France)