Problem will back in not long time. Check flow on the DPF additional fuel injector. I think so flow is low or no flow.

@LMAutoRepairs

4 жыл бұрын

As I already replied... this was done in May last year, and so far still going... if it come back, I will update... 👍 Thank you for watching!

@nashidkhan9831

4 жыл бұрын

Good sir

@stumo8681

4 жыл бұрын

No injector on a DPF, it regenerates by a post injection strategy in the ECU

@fabini14

4 жыл бұрын

@@stumo8681 some dpf have a injector, not all post injection

@LMAutoRepairs

4 жыл бұрын

Thanks! 👍👍👍

I advise anyone doubting this guys diagnostic ability to watch a few more of his videos. His skill is up there with the best!

@LMAutoRepairs

4 жыл бұрын

Appreciated! Thanks! 👍👍👍

@andrewyeo2353

4 жыл бұрын

Second that brilliant at finding the solutions love the channel

@LMAutoRepairs

4 жыл бұрын

@@andrewyeo2353 😊 Thank you so much! 👍👍👍

If you cannot clear the codes, disconnect the maf sensor, start engine, turn off engine and the connect the maf sensor. Clear codes will then let you start static regeneration

Job done nice to see the regeneration done with the Maxisys, warm jumper required 🥶 😊👍👍👍

@LMAutoRepairs

4 жыл бұрын

Lol Thank you for watching and for your comment Igor!

@neilmurphy845

4 жыл бұрын

Could you put the heating on whit the AC button pressed

@ukcitizen1158

4 жыл бұрын

@@neilmurphy845 Yes.

@neilmurphy845

4 жыл бұрын

@@ukcitizen1158 ya knew May's micra did that when you put the heating on wounder why he didn't do that then

Thank you for another great video!!! Comment section is very good too.

@LMAutoRepairs

4 жыл бұрын

Thanks! 👍👍👍

You did almost everything alright . I would have mentioned to check the oil ( fuel in the oil ) I understand you couldn't do a drive cycle this would have given you a clearer view in actual values . For those who thought about your neighbours I have only one thing to say . That's the price you pay for wanting a cleaner environment that turned out to be a big and expensive failure .

Schön das du da bist.. spannende Erklärung! Danke! ;) Hast du schon mal das wasserstoffreiche Wasser Wasser aus einem Wasserstoffanreicherer schon mal getrunken? Dieses Getränk ist einfach geil! 🌱 Wer kennt das schon? Hmm das kann ich dir jetzt nicht verraten.. Ein Beispiel von mindestens 15 positiven Wirkungen: Wasserstoff schützt alle Organe Kleiner Tipp: es schmeckt richtig gut .. ❤

ALWAYS PREFER STATIC AT LEAST AT VW AND AUDI..THAT IS WHAT I WORK ON....AMAZING IS THE FACT THAT IT LET U REGEN WITH NO FUEL.....WELL DONE....

@LMAutoRepairs

4 жыл бұрын

Lol... yes, fuel was a bit low... Thank you for watching and for your comment!

@tcifusion4497

4 жыл бұрын

@@LMAutoRepairs A VW WOULD NOT REGEN AT THIS LEVEL OF FUEL.U NEED 28LTRS AT LEAST...

@LMAutoRepairs

4 жыл бұрын

@@tcifusion4497 Yes... I know some cars will do that... 👍👍👍

@andrewbancroft6174

4 жыл бұрын

@@tcifusion4497 I know a place where people make sure they have plenty of fuel when they take their cars in, otherwise if they are low on fuel he fills fills them up with red.

@tcifusion4497

4 жыл бұрын

@@andrewbancroft6174 HOPE THAT PLACE IS AT GREECE !!!!!LET ME KNOW!!!!THANK U....

Nice video Luis thanks for sharing

@LMAutoRepairs

4 жыл бұрын

Thanks Ian! For watching and for your comment!

Nice job and good luck....

@LMAutoRepairs

4 жыл бұрын

Thanks! 👍👍👍

Very helpful information

@LMAutoRepairs

4 жыл бұрын

Thanks! 👍👍👍

This would freak me out! I've never done work on a diesel with DPF (all have been without DPF). The fact that it has to peg at such a high RPM would make me nervous. Interesting process.... I have done light studying on these systems, but what I'm unfamiliar with, makes me nervous. Lol Excellent video Luis!

@LMAutoRepairs

4 жыл бұрын

Hi Yes, it can be scary... that's why I always prefer to do it while driving... safer and better for the engine... Unfortunately on this occasion was not possible... Thank you for watching and for your comment Cuba! 👍👍👍

@liamsbargains6129

3 жыл бұрын

I use Forscan and a bluetooth OBDII device while I'm driving and can see the DPF heat build up to 620'c during dynamic regen!!!! You soon start going meh after a few times LOL

@CubasAutomotive

2 жыл бұрын

@@markaskew since then, I've done tons of work on DPF and even recently took an ATG training class on the systems, along with how to more accurately diagnose issues throughout the system. Crazy how much I've learned since then, come to think of it.

Before doing the regeneration I would have done a physical inspection of the DPF pressure differential pipes as they crack and perish and collapse. This maybe the reason the readings post regeration were high for a few minutes.

@LMAutoRepairs

4 жыл бұрын

I actually did a visual inspection before start... There is a bit of background story with this car, which I decided not the go through on the video...😉 Thank you for watching!

@errol8000

2 жыл бұрын

My pipes were really bad they would literally crumble in your hands, I bought replacements and they were made of silicon so that should cure that problem.

Nice video , I did few " forced regeneration " on dpf ...but how you said it's pretty dangerous as the car gets very hot and if it's leaking oil from engine or it's not cleaned properly get start burning.

@LMAutoRepairs

3 жыл бұрын

👍👍👍

Thanks for video 👍

@LMAutoRepairs

4 жыл бұрын

Thanks! 👍👍👍

Just go on the highway and keep your car at about 3000 rpm 4-5 gear to match the rpm. I usually go once in a week or 2 weeks on highway and go about 140kmp for about 15 minits and then i can really feel the car having more power and going very well, because you can clough up the car in the city going slow speeds and low rpm.

*The engine is very happy to do this. This is just a momentary solution.*

@LMAutoRepairs

4 жыл бұрын

Well... been going for nearly a year... so, not too bad...😉 Thank you for watching and for your comment!

A lot of people have diesel cars and do not need them not doing the miles 😀😀

Super film. Pozdrawiam

@LMAutoRepairs

4 жыл бұрын

Thanks! 👍👍👍

@-xYz--nk1gm

4 жыл бұрын

Akurat o dpf to chyba grupa vag jest lepsza..mozesz na androidzie uzywac apki vagdpf zeby wiedziec kiedy sie chce wypalic.;)

Normaly preasure above 50mb are not ok.I think its full.Needs cleaning or some alterlative technics.

Top man

@LMAutoRepairs

3 жыл бұрын

😊 Thanks! 👍👍👍

I heard that dfp filter (on this engine) have a accept procent for working fine. Can you tell me who is that procent? More then 50% need regeneration?

my mrs had this engine in a mazda , nothing but problems with dpf light coming on , £50 quid to top up dpf fluid then £40 quid for garage to reset the dpf fluid code . Worked fine for a month then dpf codes come back on we took it up motorway in 4th gear and gave it blast out . light went out and everythink fine for few weeks and then happen again. She had a Ford cmax 1.8tdci before and all that had was same problems and costing her money because stupid dpf codes kept coming up . In the end i told her to get rid of the car and buy a petrol engine . Her dads having the same problem with the dpf on his car and he said he NEVER BUY A DIESEL CAR again . I told her now keep away from diesels with dpf on . Nothing but problems and too much and too expensive on them . She had a ford focus 1.6 petrol now for a year and had no problems whats so ever . Every diesel car she had as had nothing but problems with dpf, egr clogging injectors .

I think the health and safety message about hot exhaust gases, adequate ventilation and all of that should probably warn you that you will be subject to the sound of a diesel sitting at 4k possibly causing depression. If conducted outside of a workshop environment the forced regen may also piss off your neighbours quite badly😆

@LMAutoRepairs

Жыл бұрын

☺️ 👍👍👍

I did few static regen on ford by snap on tool and i can say is more gentle vs your tool,revs are only up to 3k and whole process take about 25-30min,you should also check oil level before and after,make sure fuel is at least 1/4,coolant level and alternator belt.Basic things to not allow any mistakes can cause engine failure.

@LMAutoRepairs

2 жыл бұрын

👍👍👍

@stevenlogie7654

2 жыл бұрын

I have been trying this but everytime I get to start it comes up saying procedure aborted it may not be necessary for this vehicle 🙈

@grzes134

2 жыл бұрын

@@stevenlogie7654 what did you use to do it?

Just an advice I was working in Ford service. When you regenerate do not start the air condition. By us there was a lot of air conditionig compress which had gone during regenerate

@LMAutoRepairs

4 жыл бұрын

That's a great piece of advice! Makes sense... Thank you very much! For watching and for your comment! 👍👍👍👍

Hi love your video , can you please do a video on dynamic regeneration thanks

@LMAutoRepairs

3 жыл бұрын

👍👍👍

I share your concerns - I've done several succesful static regens using maxi sys but the last one, on a 1.6 tdci Focus, resulted in terminal big ends knocking! Be warned people.

@ukcitizen1158

4 жыл бұрын

On Ford & Mazda, when the DPF is clogged and you have the Ash Accumulation codes, you have to do an Oil & Filter change prior to a Forced Regen. Big End Knock was due to excessive Diesel Saturation of the Engine Oil. You inadvertently caused the Knock to occur.

@darrellcook7837

4 жыл бұрын

@@ukcitizen1158 Yes, in hindsight that makes sense. Learned the hard way though!

@ukcitizen1158

4 жыл бұрын

@@darrellcook7837 In this game, you live and learn..... Technology and Special Functions are constantly updating and evolving, but, Technicians are failing to take Workshop classes and don't seem to have a tendency to keep abreast with manufacturers Bulletins, unless they are working in a Dealership or are passionate about what they do. These Bulletins are provided for a reason. They are essential! Technicians owe it to themselves and to the consumer to provide the consumer with a value for money, professional service, which then goes to show that said Technician is clued up and knows what he/she is taking about. Results speak for themselves. If you had access to Bulletins, you would have known about Diesel Saturation since 2007. Investing in Auto Data will go a long way.

@nemanjadzombic6101

4 жыл бұрын

@@ukcitizen1158 Well I'm passionate for this job and I do not take any classes. Internet and videos like this work fine for me.

We need to more videos on forscan please

@LMAutoRepairs

Жыл бұрын

I think I have more coming, where I used Froscan... 👍👍👍

Is it dosing the DPF fluid correctly? On my 1.6 TDCi I found an intermittent reed switch / sensor that detects magnet on the fuel filler flap so was not dosing on each fill up. I would also have added a DPF cleaner into the fuel tank before doing a static regen. My idling pressure is 0.3 and has only ever reached 1.6 on a run. Hopefully it will continue to go down now

@ludvigericson6930

2 жыл бұрын

There is no DPF fluid on these engines, as far as I know.

mine has been cleaned, also advise against supermarket fuel. shell esso, gulf are ok, tesco is really bad for them, many have mensioned it to my freind at the garage he works for

@LMAutoRepairs

4 жыл бұрын

Agree... that poor quality fuel does not help! Thank you for watching and for your comment!

@TheMcooper17

4 жыл бұрын

@@LMAutoRepairs people have thought, "take the restriction out, more torque and better fuel econmoy at the risk of a little black smoke

5 mph average speed. That is your DPF problem. Owner should sell this and buy a petrol. The rest of the codes are from a failing gauge cluster. Common on these cars.

@liamsbargains6129

3 жыл бұрын

My guess would be that the computer may have been reset recently and spent majority of time sat on driveway which is why the road tax has expired.

👍

I had the same car, same engine but '06 made focus. I had never had a dpf problem till 200.000km and I sold the car, the engine performed like new. I have some recommendations to the owner; - always buy high quality diesel, like shell v-power - avoid going low revs on long times, use the engine on 1700-2500 rpms daily driving - from time to time, go on a highway and go up to between 3000-3500 rpm on third or fourth gear, drive like this for 10-15 minutes to clean up the exhaust and dpf system.

@LMAutoRepairs

4 жыл бұрын

Thanks! For watching and for your comment!

Hi i have the same problem P242F pressure at idle is about 0kpa and at 3000 rpm is 20kpa which means 200 hPa, according to my experience for 1.6L duratorque the pressure at 3000 RPM should be around 30 hPa which means I have to much pressure (200 hPa). I wanted to do a static regen. I’m not able to delete the fault code P242F so the PCM refusing to enter the regeneration mode how did you delete the fault? Thank for the help.

@LMAutoRepairs

3 жыл бұрын

Try a dynamic regeneration... See if it does it... If the pressure is too high, the car might refuse a regeneration due to safety reasons... In that case replace the DPF, or remove it and clean... 👍👍👍

I think you could do with some 'trade plates'

@LMAutoRepairs

4 жыл бұрын

I know...😉 Thanks!

You don't use the jlm dpf cleaner? In my ford focus with 100 000kms, the 20 000kms a 20 000kms i put 375ml of jlmdpfcleaner e saw far zero problems. Best regards from portugal. Nice e informative video. Post more for your focus.

@LMAutoRepairs

4 жыл бұрын

Hi... Personally I don't use those additives.... I do have more focus videos coming... Stay tuned! 😉 Thank you for watching and for your comment!

@pedroresolve

4 жыл бұрын

@@LMAutoRepairs ok. Your ford focus has the power botton to start? I want to instal the drl's but i don't no to start. Do you help me?

@LMAutoRepairs

4 жыл бұрын

@@pedroresolve This car was not mine... I don't own a focus...

@liamsbargains6129

3 жыл бұрын

Exactly the same stuff I used

And as with ALL China diagnostic machines, read how to regen using the proper VCI to get an idea what the procedure will be. Autel, Launch etc. etc. make you think you have to turn off the ignition when you have to leave it on. When doing anything on a Ford and a 600 second counter appears, leave it running. 600 seconds is 10 minutes which is Ford's favourite timer length. With the readings after you finished this one might be back.

@LMAutoRepairs

4 жыл бұрын

Next time I will use IDS... to see the difference then...😉 Thank you for watching and for your comment! 👍👍👍👍

@timmehlittleloud2251

4 жыл бұрын

@@LMAutoRepairs I'd just fire up KZread just to get a rough idea. Been caught out with Autel b4 👍

@LMAutoRepairs

4 жыл бұрын

@@timmehlittleloud2251 👍

I bet your neighbours love you 😂😂

@LMAutoRepairs

4 жыл бұрын

They do... I fix everything for them! 😛Lol 👍👍👍👍

I have done only one static on a 2.0 tdci kuga, but it only revved up to 2750 rpm not 4000 like this focus. It went well but it used the entire 10 min. Doesn't t the focus use the Eolys reservoir? Does the autel shows any information about that? All the best!

@ukcitizen1158

4 жыл бұрын

Some do use it. In those cases, there is an option to select the Module and read the data in regards to fluid levels and there are Actuation & Test Procedures in Special Functions. There is also an option to reset the Counters back to zero.

@LMAutoRepairs

4 жыл бұрын

Never checked... as was no faults for anything else... I don't think these ones have the additive... They use a small injector in the exhaust... Thank you for watching and for your comment!

Hi..Dynamic regeneration never herd of this...take it you drive car on motorway and force the same process as static

@LMAutoRepairs

3 жыл бұрын

Yes... that the one... Thank you for watching!

With the differentiel pressures this high after a static regen, the p242f will be back within a week. Its shouldn't be higher than 40 to 50 mbar at 3000 rpm. Does this car have the extra injector before the dpf? Most fords with a p242f have a failed 5th injector in the exhaust.

@LMAutoRepairs

4 жыл бұрын

Possibly... this was done in May last year... and car still going... at least lasted more than a week....😛 If comes back, will have to check... Thank you for watching and for your comment!

@YarmouthMark

Жыл бұрын

What you are referring to is a vapourizer. Not sure this year make would have that.

Reving a cold engine to over 3000 rpms, perfect 👍🏻 also the computer said engine must be warm...

@LMAutoRepairs

4 жыл бұрын

👍

@lronMan88

2 жыл бұрын

@@markaskew yeah I know, so a forced regen needs at first a hard forced heating on cold engine like in the video to regen with damaged piston rings and valve seals 👍🏻

bet the neighbourhood loves to hear agricultural engines run flat out for 20 minutes at a time

@LMAutoRepairs

4 жыл бұрын

LOL A bit exaggerated... and as I already answered a few times, this is was the second regen I did on my drive way in about 10 years... For all matters, it could be my own car... Thank you for watching!

@matteightytwo

4 жыл бұрын

@@LMAutoRepairs I did a Liqui Moly diesel purge on my TT, I felt very cringy holding the revs at various levels for 10 minutes, but it did work. Noticed you had an Autel, you have the model I wanted but couldn't quite justify the cost for as a home gamer Nice channel though, love the content 👍

@LMAutoRepairs

4 жыл бұрын

@@matteightytwo That's great, that you got it sorted... Agree that this Autel is a bit too much for the home user... but there is more suitable models out there! 👍👍

@liamsbargains6129

3 жыл бұрын

Round here I'd rather hear that than the current trend of young dweeby drivers over fuelling so their exhausts go bang bang bang

Hi there I have same problem. How u rest code From ecu. I have 3 scanner not let me do it

@LMAutoRepairs

3 жыл бұрын

Just as per the video... If you can't do it, either there is still a problem with the car, or your tools can't do it... Thank you for watching!

you should get some trade plates if you get a car with no mot or tax or what ever as it covers you to drive the car on the road it is a lot of paperwork to recive but its alright paperwork it really depends as i am a driveway mechanic and i have trade plates as i get a lot of cars to repair and need to road test

@elliottpeters2996

4 жыл бұрын

What is the "whatever"? As far as I am aware, trade plates are a portable tax disc and nothing more.

@s3bby513

4 жыл бұрын

Elliott Peters tax and insurance as you have to provide a motor trade insurance. It’s really used by garages and car trade if they moving it to one place.

@elliottpeters2996

4 жыл бұрын

@@s3bby513 I am aware of the requirements to qualify for trade plates.I am just saying that they absolutely do not provide blanket coverage to drive any vehicle, in any condition, on the roads. Their sole purpose is to negate the need to register and tax a roadworthy vehicle whilst it is being moved from place to place, test driven by a potential buyer, or following a repair.. Provided you have valid insurance, it is not necessary to use trade plates to drive to and from a pre-booked MOT test. Nothing can prevent you falling foul of the law if you are driving an unroadworthy vehicle.

Can DPF Regen cause Car Fire? I was doing the Regen for my Vauxhall insignia 2009 & after 15 min smoke appear from the Aircon vent, I was scared and stopped the Regen. It did it job, Reduce sooth from 255% down to 68%

@LMAutoRepairs

Жыл бұрын

It can... that's why I usually try to do a dynamic regeneration, or force it while driving... Stationary regenerations are more risky, and even though I did it on this video, when possible I do it while driving... 👍👍👍

Can the dpf codes be reset automatically if a manual dpf clean is done by taking it up the motorway for an hour in 4th?

@LMAutoRepairs

2 жыл бұрын

Depends how blocked it is... It worth a try... 👍👍👍

Why do you have to have lights on air con to do dpf cheers.

@liamsbargains6129

3 жыл бұрын

To add a little load to the alternator to warm up engine quicker and then to use the power given off from the alternator giving max while the car needs to be revved hard during the static regen process.

❤🎉😊

@LMAutoRepairs

Жыл бұрын

☺️ 👍👍👍

Done this on a 2014 Focus and the problem just comes back again and again after a couple of months. Just a temp fix. Patch it up, knock the lights off, and get rid.

@LMAutoRepairs

3 жыл бұрын

This one still going... Obviously make sure everything else is good so the car then continues to do the regenerations etc... Thank you for watching and for your comment!

@sbrader97

Жыл бұрын

Yeah you could have other issues thats preventing the car from doing regens like low fuel level, bad thermostat etc or the dpf is full of ash which u cant burn off with regens in which case u should get the dpf manually cleaned out or buy a new one cleaning will be cheaper but sometimes they can be melted and damaged beyond cleaning

Are these fitted with Eloys the same as the Peugeot’s ?

@LMAutoRepairs

4 жыл бұрын

No... Don't think they are... Thank you for watching!

I can't remove the fault code so I can't strat regeneration process

@kp-qr6hy

3 жыл бұрын

Matyas if u disconnect the maf sensor a couple of times and clear the maf codes it will let u clear the dpf codes

What do you think about the additives to clean the dpf that reduce the melting point of the particles?. Or perform a decarbonization with machine and hydrogen?.

@LMAutoRepairs

4 жыл бұрын

Personally, I never used those additives, nor have used those machines or that service.... Thank you for watching!

@cransaftvalve734

4 жыл бұрын

@@LMAutoRepairs thanks

@jothain

4 жыл бұрын

Imo additives are generally speaking the best snake oil's sold.

@LMAutoRepairs

4 жыл бұрын

@@jothain Agree! 👍

@tommycunnion5295

3 жыл бұрын

What macias r u use I

The ash accumulation not solved with a regeneration, must remove the dpf and clean it....

@LMAutoRepairs

4 жыл бұрын

Yes... that's correct! Thank you for watching and for your comment!

Can I ask what Autel do you use ?

@LMAutoRepairs

3 жыл бұрын

MS908P... Thank you for watching!

What think your neighborhood about DPF cleaning process :)

@LMAutoRepairs

4 жыл бұрын

Lol I always do it on the road.... I think this is second time I did a static here in 10 years.... Thank you for watching!

@MrFluorescentify

4 жыл бұрын

I think all vote for Brexit.:)))

@LMAutoRepairs

4 жыл бұрын

@@MrFluorescentify 🤣🤣🤣🤣👍

Thanks for sharing Bro👍 very valuable information, especially for me, what are the ideal pressure readings on a known good dpf & You're awesome😎

Hey buddy, does your autel go into Mercedes braking systems? I use Delphi ds150e (Chinese clone) And it doesn’t get into the braking system on Mercedes vehicles. I’m looking at getting a proper system and spending some good money on a system. Which would you recommend?

@LMAutoRepairs

4 жыл бұрын

Yes... the Autel does... Thank you for watching!

@luketuttiett

4 жыл бұрын

LM Auto Repairs thank you for the reply! What model is it? Cheers for the videos! Helps us tinkerers out!

@buildstoys

4 жыл бұрын

@@luketuttiett Maxisys 908P

@LMAutoRepairs

4 жыл бұрын

@@luketuttiett My one is the MS908P 👍

You should really make sure to preheat the engine up to operating temperature. Do not do as he did in the video as the engine temp was clearly to low. This could very easily create engine damage

@LMAutoRepairs

4 жыл бұрын

Again, that's why the regen never started until the engine was up to the necessary temp... Thank you for watching and for your comment!

You are turning on the front heater instead of the back windshield.

@LMAutoRepairs

4 жыл бұрын

Either is an electric load...😉 Thank you for watching!

What was that about the codes 9:30 ??

@LMAutoRepairs

4 жыл бұрын

The codes in the ecu that tou see at the start of the video... you need to clear them before starting the regen... Thank you for watching! 👍👍👍

In my citi, 30 workshop never is regeneration finished. Ford 80 kw. 1 is burning. This is video.

hello good afternoon, what is your diagnostic machine ??? Autel? model ?? thank you !

@LMAutoRepairs

3 жыл бұрын

Hi Autel MS908P... Thank you for watching!

@nccarvalho7887

3 жыл бұрын

Hello friend, are you an Autel representative? I am looking for a diagnostic machine which model do you advise? Autel MK808BT is a good choice? thank you very much

@LMAutoRepairs

3 жыл бұрын

@@nccarvalho7887 Depends what you want it for... But is a good choice. Check their website, and compare the different models... Will help you making a decision... No, I am not an Autel representative.

Did you just use a generic scan tool to run the regen?

@LMAutoRepairs

3 жыл бұрын

Autel MS908P... Thank you for watching!

@gurauoctavian4047

3 жыл бұрын

You can buy Autel Ap 200 , it's a little obd tool from autel that have nearly everything and it's free for 1 make.

Is the regeneration needed even if you always run clean engine oil?

@LMAutoRepairs

4 жыл бұрын

Yes... Thank you for watching!

Just put the fluid for dpf it's under the car and it's all done

@LMAutoRepairs

Жыл бұрын

It is slightly more complicated than that... But thank you for watching and for your comment! 👍👍👍

Seriously dont try this if your DPF is blocked. It can damage engine or one of many other things

@LMAutoRepairs

5 ай бұрын

If it is heavily clogged yes, it is risky... 👍👍👍

I don't understand why people even bother with those silly diagnostics all in 1 tools :D when you have Forscan that is Ford specific and all features just work ;)

@LMAutoRepairs

2 жыл бұрын

If you only work on ford's yes... make sense... Try to scan a BMW with the forscan tool...🙄 Thank you for watching and for your comment!

DONT TRY THIS. If DPF is blocked, it can severely damage something under the hood. It happened to me and it will happen to you

@LMAutoRepairs

5 ай бұрын

If it is severely blocked yes... 👍👍👍

Dpf off and flush it with water and dpf cleaner. Takes 2h all together

@LMAutoRepairs

4 жыл бұрын

You can only do what the owner of the car is willing to pay for.. 😉 If that makes sense.. Thank you for watching and for your comment! 👍👍👍

@MartinTeerly

4 жыл бұрын

@@LMAutoRepairs fair enough 👌🏻

@liamsbargains6129

3 жыл бұрын

@@MartinTeerly Plus that is an awful lot of crap on the customers driveway! ha ha

I'm glad I don't live near you having people's cars revving like that in the street....

@LMAutoRepairs

4 жыл бұрын

Lol Was this one in many years... I usually do it while driving... Was this one that had no road tax... Thank you for watching!

@liamsbargains6129

3 жыл бұрын

Once in a blue moon won't hurt

What is a DPF? (sorry if stupid question)

@LMAutoRepairs

4 жыл бұрын

Diesel Particulate Filter en.m.wikipedia.org/wiki/Diesel_particulate_filter Thank you for watching and for your comment!

@konradc12

4 жыл бұрын

Diesel Particulate Filter (DPF) is what it says. Diesel engines have particulates which are harmful to the lungs. The filter is designed to capture these particulates and burn them off during a normal regen cycle. The regen cycle tends to happen when the car is driving at a constant, like fast road or motorway. Depending on the car, regen uses either a fifth injector. As corrected by Ian U, ad-blue is used to reduce other emissions! This why modern diesels are not suitable for town driving. If they are not given the time to regen, the DPF will get full causing the issues shown in the video. Here is a Wiki on the subject - en.wikipedia.org/wiki/Diesel_particulate_filter Some petrol direct injection cars are starting to have particulate filters too - www.autocar.co.uk/car-news/industry/volkswagen-equips-petrol-cars-particulate-filter-technology

@markbuckley5109

4 жыл бұрын

Thanks, I had a message engine systems fault on a focus and this appeared, so thought there might be a connection.

@supernoodle48

4 жыл бұрын

@@konradc12 Adblue has nothing to do with DPFs. Adblue is the reagent used with a Selective Catalytic Reduction system for reducing NOx emissions.

@konradc12

4 жыл бұрын

@@supernoodle48 Thanks for correcting me. I will amend my reply. 👍

Definatly almost full of ash - needs clean out or replacement.

@LMAutoRepairs

4 жыл бұрын

When it fails again... 👍

@jothain

4 жыл бұрын

@@LMAutoRepairs it depends heavily on usage I guess. I have 2.0tdci that has almost 600 000km's on clock and to my knowledge has original dpf installed. I got error once, but rubber hoses for sensors where fried. But yeah. I most definitely wouldn't buy dpf diesel engined car if I was driving constantly less than 20km rides. I noticed that I usually run car for about 25km's or more when regeneration has triggered automatically. It's really easy to dismiss required stats for it to trigger. If I recall correctly there's engine temp, running time for engine, required speed for specific time and exhaust temperature requirements.

how weird is to see the steering wheel in the right :)

@LMAutoRepairs

3 жыл бұрын

You get used to it...🤪😉 👍👍👍

@antibolsevism9814

3 жыл бұрын

@@LMAutoRepairs I'm going to have my first car a ford focus exactly like this, these videos gonna help me to not kill the Turbo and the DFP

@LMAutoRepairs

3 жыл бұрын

@@antibolsevism9814 👍👍👍

Reving a cold diesel engine (at 3:32)... What a good idea...

@LMAutoRepairs

4 жыл бұрын

Again... the engine was warmed by the time the regen started... Thank you for watching!

diesel cars are more problematic. Good job

@LMAutoRepairs

4 жыл бұрын

They are all problematic... in one way or another... lol Thank you for watching and for your comment!

Can this be completely removed from the system and just use a normal exhaust system? I'm aware of the legal requirements, but lm sick of technology and want to get back to basics. Air pollution is caused by volcanoes and Chinese and Indian factories America is the worst. Cars play a roll too but for the amount l drive (120 klm per month) I want to bypass this system.

@LMAutoRepairs

2 жыл бұрын

LOL I agree to a degree... Governments are focused on the small stones, and ignoring the big ones... That said, yes, it is possible... 👍👍👍

@Jim.Thunda

2 жыл бұрын

@@LMAutoRepairs How? I have a Ford focus 2009 South Africa build, the engine warning symbol came on then awhile later the engine malfunction light. Called a tow truck ,mechanic said his code reader couldn't communicate with the car, told me to take it to Ford dealership ($240 per hour) Possibly $3000 to fix it, the car is not worth it. Now l just want to get rid of the system and not have a sensor show up a code. So please help if you can I'm an aged disabled pensioner and can't afford the scammers at the dealership. I need my car to get groceries and doctor appointments.

@Jim.Thunda

2 жыл бұрын

@@LMAutoRepairs Please read my last post, I'm getting desperate. Regards.

@LMAutoRepairs

2 жыл бұрын

There is nothing I can do remotely... Tools are needed, look for someone near you that has the necessary equipment to do it...

@Jim.Thunda

2 жыл бұрын

@@LMAutoRepairs If l know what to do l can do it myself, I'm sick of paying out $145 per hour to workshops that take their time and do nothing other than tell you that it needs parts that are more than the car.

rather spiffing video-choreography old chum, good show what what

@LMAutoRepairs

4 жыл бұрын

😛 Lol Thanks!

this proses make me nerves,,,, 😬😬😬

@LMAutoRepairs

Жыл бұрын

It is a bit unsettling... I do prefer 100% to do them dynamically, while driving... 👍👍👍

Stop skipping and read the screen FGS

@LMAutoRepairs

3 жыл бұрын

👍

Cold engine? Its joke? 4rpm?

@LMAutoRepairs

4 жыл бұрын

Whatever...🤦‍♂️ Have answered that same question many times... Thank you for stopping by...

@liamsbargains6129

3 жыл бұрын

The software waited until the car had warmed up before doing the regen or were you watching a different video?

Dobt buy ford nothing problém

@liamsbargains6129

3 жыл бұрын

This engine is used by many manufacturers!