Top video, done in a real world environment like most of us have to. No fancy hoist, no press, you’ve inspired me to get on and do mine.

Thanks for the video, going to do my AU bearings in the next week or two, this video gives me the confidence to give it a go.

Thanks mate. That was a great help. I ended up popping down the road to a local (bush) garage to get that collar pressed back on, so it cost me a 6 pak, but that’s still pretty good value! Cheers.

Very good video, without workshop and press. I really liked and followed every step. Went fine thanks heaps.

Howdy bro. Thanks for your post effort. I would of loved to have seen you put that bearing collar on after heating up the collar on an old iron and freezing the axle . Love the freezer idea while no one is looking . Big thumbs up.

@TerryJonesPrinterRepairs

Жыл бұрын

If you have a big enough freezer for the axle 2 hours in the freezer the heated collar just slides on with fingers no effort with a hammer and a pipe needed.

@statewidefilms

Жыл бұрын

@@TerryJonesPrinterRepairs bloody brilliant. Sounds to easy . Cheers

One handed 10/10

luv the safety shoes pity about the hot an cold part

Torx lever definitely won't undo that hex bolt.Otherwise,good job.

good work thanks

Super helpful video! Wish mine was as easy as yours though 😂

@TerryJonesPrinterRepairs

Жыл бұрын

Australian Ford's built reliable and simple to repair so if you get stuck outback you can get yourself unstuck.

super helpful vid. dont need to do the bearings but last owner put the backing plate with the caliper bracket on the wrong way. caliper sits are the rear and not the front haha. looks like i just need to undo the 4 hex bolts and pull swing the plate around

Thanks

not bad , im doing one again two years later, the seal is weeping against the axle, amazed its that easy how you pushed the axle in, i always stress with any seals.

@TerryJonesPrinterRepairs

10 ай бұрын

The seals in the kit I used are crap quality as mine have a small weep. Clean the housing up with turps and apply a super thin smear of rtv on half the outer edge of the seal to make a good seal.

@closertothetruth9209

10 ай бұрын

@@TerryJonesPrinterRepairs mine was leaking against the rotating axle, my freind a mechanic and mechanical engineer said , yeh the seals used to last 20 years and what he does which i saw him do years ago is before he installs shaft seals is he removes the internal seal spring tensioner and shortens it about 3mm he said when he does that he never gets leaks, he also said to put a NON silicone sealant on the outer seal surface before you install it SO here i go again LOL.

I have also seen u can take the disc and calliper off as one mate

Hi mate am I able to just re pack this Bering in an emergency situation

When these go bad does it feel like the wheels are wobbling, because its not the wheels. And the wheels are not buckles

What brand bearings do u use mate? I have a 04 xr6 that needs rear bearings changed..pls let me know

@TerryJonesPrinterRepairs

Жыл бұрын

Timken are the best. But if you don't plan on rebuilding both sides and the diff carrier bearings all at once and changing the diff oil the iron from the inner race I show in the video is floating around inside the diff damaging everything it doesn't just magically dissolve or disappear. That's why I use those cheap shity Chinese bearings as I only want the car to work for another year or 2. Any bearing that fails leaves little bits of iron floating around in the oil.

@michaeljust2253

Жыл бұрын

@@TerryJonesPrinterRepairs thankyou mate mine is irs and am looking for the rear bearings to be replaced.i got told when I got tyres that mine are on the way out and not having much money I'm just trying to get it done for peace of mind..

@TerryJonesPrinterRepairs

Жыл бұрын

@@michaeljust2253 IRS is completely different to this, nothing in this video applies to your problem. You are better off watching a ford territory rear bearing replacement video .

When these fail will it cause a ting ting noise under acceleration and i changed my cat already ?

@TerryJonesPrinterRepairs

Жыл бұрын

these cause a rumble noise in the rear.

@TerryJonesPrinterRepairs

Жыл бұрын

You may have bad universal joints

do you know how many km those bearings had on them?

@TerryJonesPrinterRepairs

Жыл бұрын

Au falcon wagon rear wheel bearings typically fail 290-315k, the iron that breaks off the inner race then floats around in the diff oil and takes out the carrier and pinon bearings at 360-370k

@namenotshown9277

Жыл бұрын

@@TerryJonesPrinterRepairs thanks for that

My Au wagon is making a grinding noise from the Right rear wheel when I turn to the right only. Sounds like a metal on metal. Hope it's not a bearing or worst. Thanks for the video.

@TerryJonesPrinterRepairs

9 ай бұрын

Time for pads or your muffler is hitting the tailshaft

Always insist on timken bearings made in USA.

@TerryJonesPrinterRepairs

Ай бұрын

I prefer Timken Bearings from Birmingham, Great Britain. They last well long.