Big thanks to you from Thailand! I really love the internet

was starting to get frustrated with binding😂 thankyou, you are very informative🙌🏻

Such a great tutorial!

You need to start a merch store with all your crazy sayings….”No dirty tips - Mazz Designs”. 😂😂

@mazzdesigns6929

Жыл бұрын

I have been told I have my own kind of vocabulary lol hope to have some merch soon!

Yea boi!

You’re the man thank you for the badass video dude just got a handful of these receivers!

@mazzdesigns6929

3 ай бұрын

Thank you for the support!

And make sure and plug it up correctly when you’re done! 😂😂😂😂 - Word Mazz!

@mazzdesigns6929

Жыл бұрын

Yes sir. Don’t worry I tried driving it without hooking motor up lmao

You can put a bit of heat shrink on your clips to cushion them.

Nice tutorial on soldering up those micro receivers.

@mazzdesigns6929

Жыл бұрын

Thanks dirk I really appreciate it!

Saved me a ton of time looking for a solution. Thanks 🙏

@mazzdesigns6929

8 ай бұрын

Great to hear! Happy Thanksgiving to you and your fam!

Hey Mazz, another great video! The “power cycle” tip is gold! I had to search the dark web to find that tip about a month ago. Thanks again for dropping the knowledge. Looking forward to the Furitek lizard pro / bec wire tutorial!

@mazzdesigns6929

Жыл бұрын

Always my man I appreciate all your support as always. Dig seeing everyone’s comments

Thanks for these great videos always appreciated

@mazzdesigns6929

Жыл бұрын

Thanks for watching and taking your time to comment I really appreciate the support!

Thanks man

@mazzdesigns6929

Жыл бұрын

Yes sir anytime thank you for watching!

Great video. You can put some shrink tubing on the alligator clips so they won’t scratch anything

@mazzdesigns6929

Жыл бұрын

Thanks Kurt! I like living on the edge tho! 😂

Have you tried these with the RadioMaster MT12 4in1 by chance?

Great vid! Also good to do the connect and wiggle test, before you install the heat shrink. Testing is the function of each plug is working while powdered up. That way you catch any solder joint that didn't stick before you shrink wrap it. :) Any thoughts on if that power switch could be moved? Unsoldering it and add a couple wires to get it off the board. Might need a new mirco switch. But it be nice to get it outta the way to make it easier having the wire posts facing inboard. Yes/no?

@mazzdesigns6929

3 ай бұрын

Thanks for watching. We don’t recommend removing the binding switch as the button is not used but one time in most situations. The juice is not worth the squeeze for me. Definitely not a bad idea to check your work before heat shrink!

great video, thanks for sharing ... will a Flysky GT3 (AFHDS2A) 2CH transmitter work with this receiver? thanks :)

Man my receiver just shuts off whenever it gets a little hot 🤷🏼‍♂️ took heat shrink off and still shuts off

Would be nice to have the wires go back over the top of the receiver. Thanks for sharing

@mazzdesigns6929

8 ай бұрын

🤘

I used the bind plug on mine have same steps though. Have you seen the 5 channel or tried it

@mazzdesigns6929

Жыл бұрын

I have but I never use more than 3 channels myself so the 4 is adequate. Thank you so much for watching as well!

I’m planning on running this with a Losi Mini B RC Car - anyone have any range issues?

@mazzdesigns6929

3 ай бұрын

You will not have range issues for running on a track

Hi there I have this same receiver can I use it for a drone build ?

@mazzdesigns6929

7 ай бұрын

I’m not sure my man I am not familiar with drone products

Is anyone having a problem with their servo lagging with this reviever?

@mazzdesigns6929

Жыл бұрын

No sir never encountered that problem. Hopefully someone can shed some light for you! I would swap parts and transmitters out first

You said bored

@mazzdesigns6929

Жыл бұрын

Did I?

Great video man! Im going to be switching all of my 24's over to these receivers! 🦾🦾🦾

@mazzdesigns6929

Жыл бұрын

Thanks Shane its definitely the way to go!