Flex Disk And Driveshaft Bearing Replacement BMW Z4 E85 M54 DIY
Автокөліктер мен көлік құралдары
Flex disc and driveshaft center support bearing replacement on E85 Z4 BMW with M54 engine.
0:00 Removing splash shields and reinforcements
5:32 Removing exhaust
6:47 Removing exhaust manifold flange stud bolts
11:36 Removing flex disc / guibo
17:50 Removing driveshaft center support bearing
21:30 Inspecting old flex disc and center support bearing
23:06 Installing center support bearing
28:48 Installing flex disc / guibo
32:25 Installing exhaust, splash shields and reinforcements
35:44 Conclusion
Part numbers:
- Flex disc Manual: 26111227410
- Flex disc Automatic: 26117511454
- Flex disc SMG: 26117511454
- Center bearing: 26121225071
- Center bearing mount: 26127501257
Always check for parts number for your specific model and year: www.realoem.com/bmw/enUS/
Read and follow the service manual for Z4 E85 before attempting this procedure: www.newtis.info/tisv2/a/en/e8...
www.newtis.info/tisv2/a/en/e8...
DISCLAIMER:
BimmerZen assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. BimmerZen recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of BimmerZen , no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not BimmerZen.
Пікірлер: 30
Perfect, drone when driving and sometimes strong vibrations. (past a certain speed) stops briefly when not under load until engine braking comes in. Related to wheel speed and not engine speed. so prop shaft to wheels. Heard about centre bearings going and this video is perfect. I salute you.
Glad to see we wear the same gloves😂
yes!! as always best description!! like a teacher!! happy cristmas from greece!
Very well done and explained as another commenter hope I don’t have to do this to my coupe for awhile🇨🇦
Nice job , hopefully I won’t have to do this for a while on my Z4 coupe
Alright!! I can do it best recover as your good video, Thank you !!
i have done this on my e46. pretty simple to do
Great job..!
Correct me if I'm wrong but I didn't see you set any preload on the centre support bearing before tightening the bolts.
Hey, great videos I think I might have to subscribe 😅. When you drove your Z4 before replacing the bearings what did you feel and hear? I think I might have to replace these bearings as when I’m in first gear and start to move off, I sometimes get a few lurches forward and when I’m driving around 45mph /70 km/h there’s a slight whining sound coming from the rear end. Just curious how the car handled before the bearing replacement. Keep the videos coming!
With my Z at almost 120k, would you recommend to get a new driveshaft because the U joint Can get damaged and would start to vibrate ?
Hi will this stop my shuddering , or do you think that’s my flywheel
Do you know where the fuel filter is located?
I have 316ti το. if you have an abs asc fault you can ask for my help
Nice vid. Please could you do a video about taking apart windbarier inside rollbar behind head? I have to replace them and cant find any proper video on youtube. Thank you ⭐
@BimmerZen
3 жыл бұрын
Take a look at the manual: www.newtis.info/tisv2/a/en/e85-z4-2.5i-roa/repair-manuals/54-slide-tilt-sunroof-soft-top/54-34-power-convertible-top/EOTdh4e Register for a free account to see the content.
Shouldnt the 2 parts slide easily by hand force back and forth?!
Dude, this Mini Press you got there for the Exhaust Studs is THE solution. I am scared as hell if I see the condition of my screws. If there is any chance you can sell this thing or build another one, please let me know, seriously! The risk of damage the average mech shops will do to catalytic converters and exhaust manifold while hammering onto those studs is too high. Greetings from Germany.
@BimmerZen
3 жыл бұрын
A ball joint separator should work as well. Try getting something like this: www.autodoc.de/hogert-technik/15778048 www.autodoc.de/werkzeuge/kugelgelenkabzieher
@anthonygillesse7242
2 жыл бұрын
Special thanks to your dad for the exhaust stud press genius
@arnoldtoth7926
6 ай бұрын
For me it didnt worked, everything bent except the bolt :D, I ended op with drilling the holes, with HSS-G Co and WD40.
Great video...question is: When I'm on the interstate and give it gas, I feel a huge vibration and when I take my foot off...it quits. Sitting still while moving from reverse to drive, I feel some abnormal clunking. Does this sound like a worn flex disc?
@BimmerZen
2 жыл бұрын
If you feel vibration on acceleration, then i would check the engine and transmission mounts first. Engine mounts are hydraulic so check for leaks and cracks. Also check for cracks on the rubber flex disc. The cracks should be pretty severe and apparent for this to be an issue. Then check for play in the central support bearing and drive shaft. Worn or damaged CV shafts can also be the culprit. Check for excesive play. Axial play is normal, but there should be little play in direction of rotation. The clunk on forward/reverse is "normal" for older cars. There is some play in all of the components and the clunk is the sound where all components align for reverse/forward driving. I also think that parking brake shoes have some play and can cause a bit of a clunk when going forward/reverse.
@lisawells4084
2 жыл бұрын
@@BimmerZen U-joints are shot! Going to replace Flex Disc, transmission mounts and entire driveshaft...thanks for your fantastic video.
@BimmerZen
2 жыл бұрын
@@lisawells4084 U-joints on driveshaft?
Is this a standard or automatic transmission? I have a standard trans 2014 435i x n55 F32 is this similar install?
@BimmerZen
3 жыл бұрын
Standard manual transmission, but procedure should be very similar as this is a standard setup on all RWD BMW's. You should be able to find additional information for your model online, for example www.newtis.info/tisv2/a/en/f32-435i-cou/repair-manuals/ (free registration required).
Hey I’m currently doing this right now but for some reason my drive shaft doesn’t spin , making it hard for me to reach some of the bolts .. do all 4 tires have to be up to get it to rotate ?
@BimmerZen
18 күн бұрын
@@brandonata5847 car in gear? Handbrake on?
@brandonata5847
18 күн бұрын
@@BimmerZen car was in gear , no ebrake since it doesn’t work. I put it in neutral though with no ebrake (as it doesn’t work) and it still wouldn’t spin freely. I can’t tell you how much i appreciate you replying so fast